Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1434  Steering Angle Sensor Output Malfunction  


DESCRIPTION

Steering angle sensor signals are input to the skid control ECU (brake actuator assembly) via the CAN communication system.

HINT:

When a malfunction occurs in the communication line to the steering angle sensor, U0126 is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


DTCs may be stored if one of the following occurs:

·

Steering angle sensor zero point malfunction

·

Steering angle sensor signal malfunction


DTC No. Detection Item DTC Detection Condition Trouble Area
C1434 Steering Angle Sensor Output Malfunction Normal communication between the skid control ECU and the steering angle sensor and abnormal steering angle sensor zero point.
·

DOME fuse

·

IG1 NO. 2 fuse

·

Steering angle sensor (Spiral cable sub-assembly)*1

·

Steering angle sensor*2

·

Skid control ECU (Brake actuator assembly)

·

Wire harness or connector



*1: for TMMIN Made

*2: for TMT Made


CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering angle sensor from the spiral cable sub-assembly*1.

·

When replacing the steering angle sensor (spiral cable sub-assembly), confirm that the replacement part is of the correct specification*1.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

*1: for TMMIN Made




HINT:
·

When U0073, U0124 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073

·

When the speed sensor or the yaw rate and acceleration sensor (airbag ECU assembly) has trouble, DTCs for the steering angle sensor (spiral cable sub-assembly)*1 or steering angle sensor*2 may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag ECU assembly) are output together with DTCs for the steering angle sensor (spiral cable sub-assembly)*1 or steering angle sensor*2, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) first, and then inspect and repair the steering angle sensor (spiral cable sub-assembly)*1 or steering angle sensor*2.

*1: for TMMIN Made

*2: for TMT Made




PROCEDURE

1.CHECK DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left to check that no speed sensor or yaw rate and acceleration sensor DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR


Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:
·

If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (airbag ECU assembly), an abnormal value may be output although the steering angle sensor (spiral cable sub-assembly)*1 or steering angle sensor*2 is normal.

·

If speed sensor and yaw rate and acceleration sensor (airbag ECU assembly) DTCs are output simultaneously, repair these two sensors first and inspect the steering angle sensor (spiral cable sub-assembly)*1 or steering angle sensor*2.

*1: for TMMIN Made

*2: for TMT Made




Result:
Result Proceed to
No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output (for TMMIN Made) A
No CAN communication system, speed sensor, or yaw rate and acceleration sensor DTCs are output (for TMT Made) B
CAN communication system DTC is output C
Speed sensor or yaw rate and acceleration sensor DTC is output D



A

2.CHECK TERMINAL VOLTAGE (BAT TERMINAL)

B

5.CHECK STEERING ANGLE SENSOR INSTALLATION

C

D

2.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
a.

Turn the ignition switch off.


b.
C239999C14
0.167,1 0.667,1.25 0.5,0.25 2.417,1.375 2.833,1.406 true 0.021,0.021 0.188,0.188 0.167,0.167 10 false *a 0.26,1.042 0.802,1.26 0.542,0.219 10 false F116 2.906,1.344 3.198,1.49 0.292,0.146 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the steering angle sensor (spiral cable sub-assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F116-6 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Turn the ignition switch to ON.


b.
C239999C15
0.167,1 0.667,1.25 0.5,0.25 2.094,1.448 1.969,1.896 true 0.021,0.021 0.188,0.188 0.167,0.167 10 false *a 0.26,1.042 0.813,1.25 0.552,0.208 10 false F116 1.875,1.917 2.198,2.125 0.323,0.208 10 false IG1
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))


Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F116-5 (IG1) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Turn the ignition switch off.


b.
C239999C16
0.167,1 0.667,1.25 0.5,0.25 1.333,1.448 1.219,1.896 true 0.021,0.021 0.188,0.188 0.167,0.167 10 false *a 0.25,1.042 0.75,1.271 0.5,0.229 10 false F116 1.073,1.927 1.615,2.135 0.542,0.208 10 false ESS
*a Front view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F116-2 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)

5.CHECK STEERING ANGLE SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the steering angle sensor has been installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>INSTALLATION

OK:

The steering angle sensor installation is normal.



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (BAT TERMINAL)

NG

6.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
a.

Turn the ignition switch off.


b.
C375644C14
0.323,1.031 0.74,1.323 0.417,0.292 2.438,1.854 2.167,1.385 true 0.125,0.052 0.438,0.208 0.313,0.156 10 false *a 0.375,1.094 0.99,1.292 0.615,0.198 10 false F147 2.5,1.813 2.958,2.01 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the steering angle sensor connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F147-5 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.

Turn the ignition switch to ON.


b.
C375644C15
0.323,1.031 0.74,1.323 0.417,0.292 2.24,1.865 1.969,1.396 true 0.125,0.052 0.438,0.208 0.313,0.156 10 false *a 0.375,1.094 0.99,1.292 0.615,0.198 10 false F147 2.302,1.833 2.76,2.031 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Steering Angle Sensor)


Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
F147-4 (IG1) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Turn the ignition switch off.


b.
C375644C16
0.323,1.031 0.74,1.323 0.417,0.292 1.635,1.927 1.313,1.406 true 0.125,0.052 0.438,0.208 0.313,0.156 10 false *a 0.375,1.094 0.99,1.292 0.615,0.198 10 false F147 1.688,1.885 2.146,2.083 0.458,0.198 10 false ESS
*a Front view of wire harness connector
(to Steering Angle Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F147-1 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)