Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1500 Fuel Sender Open Detected When IG voltage is 9.5 V or more and the following condition is detected:
·

Average input signal of fuel sender gauge assembly is 550 Ω or more 3 times consecutively


·

Harness or connector

·

Fuel sender gauge assembly

·

Fuel suction tube with pump and gauge assembly

·

Combination meter assembly


- -

WIRING DIAGRAM

for TMMIN Made


E270884E08
2.052,0.917 2.667,1.115 0.615,0.198 10 false FS 2.302,0.917 2.469,1.188 0.167,0.271 10 false 2 2.052,2.25 2.667,2.448 0.615,0.198 10 false FE 2.323,2.25 2.49,2.521 0.167,0.271 10 false 3 5.49,0.917 6.104,1.115 0.615,0.198 10 false 37 5.479,2.25 6.094,2.448 0.615,0.198 10 false 36 5.719,0.917 6.333,1.115 0.615,0.198 10 false L 5.719,2.26 6.333,2.458 0.615,0.198 10 false E 0.417,3 1.031,3.198 0.615,0.198 10 false F28 0.417,3.156 3.917,3.354 3.5,0.198 10 false Fuel Suction Tube with Pump and Gauge Assembly 5.156,3.125 7.156,3.292 2,0.167 10 false Combination Meter Assembly 5.167,3 5.781,3.198 0.615,0.198 10 false F38 0.74,1.438 1.385,2.219 0.646,0.781 10 false Fuel Sender Gauge Assembly


for TMT Made


E270884E20
2.021,0.896 2.635,1.094 0.615,0.198 10 false FS 2.323,0.896 2.49,1.167 0.167,0.271 10 false 2 2.031,2.229 2.646,2.427 0.615,0.198 10 false FE 2.333,2.229 2.5,2.5 0.167,0.271 10 false 3 5.49,0.885 6.104,1.083 0.615,0.198 10 false 40 5.479,2.25 6.094,2.448 0.615,0.198 10 false 39 5.719,0.969 6.333,1.167 0.615,0.198 10 false FR 5.719,2.323 6.333,2.521 0.615,0.198 10 false FE&B 0.417,3 1.031,3.198 0.615,0.198 10 false F28 0.417,3.156 3.917,3.354 3.5,0.198 10 false Fuel Suction Tube with Pump and Gauge Assembly 5.156,3.125 7.156,3.292 2,0.167 10 false Combination Meter Assembly 5.167,3 5.781,3.198 0.615,0.198 10 false F38 0.74,1.438 1.385,2.219 0.646,0.781 10 false Fuel Sender Gauge Assembly


CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMMIN Made A
for TMT Made B



A

2.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

6.INSPECT FUEL SENDER GAUGE ASSEMBLY
2.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
E219772C03
1.5,0.167 1.99,0.458 0.49,0.292 2.531,1.24 2.667,1.667 true 2.406,1.24 2.25,1.667 true 1.615,0.229 1.896,0.385 0.281,0.156 10 false F38 2.667,1.677 2.833,1.833 0.167,0.156 10 false L 2.208,1.677 2.5,1.833 0.292,0.156 10 false E 0.198,0.094 0.406,0.25 0.208,0.156 10 false *a
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-37 (L) - F38-36 (E) Always 13.5 to 414.5 Ω



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-37 (L) - F28-2 (FS) Always Below 1 Ω
F38-37 (L) or F28-2 (FS) - Body ground Always 10 kΩ or higher
F38-36 (E) - F28-3 (FE) Always Below 1 Ω
F38-36 (E) or F28-3 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.


Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

5.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

5.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.
E158805C04
1.292,1.313 0.688,1.313 true 1.833,1.219 2.427,0.625 true 0.219,0.104 0.979,0.292 0.76,0.188 10 false *a 2.51,0.542 2.76,0.708 0.25,0.167 10 false FS 0.458,1.229 0.708,1.396 0.25,0.167 10 false FE 0.615,0.656 1.406,0.823 0.792,0.167 10 false *b 0.615,3.094 1.406,3.26 0.792,0.167 10 false *c
*a Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly)
*b Connector A
*c Connector B


Remove the fuel suction tube with pump and gauge assembly.



b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 Always Below 1 Ω
A-3 (FE) - B-1 Always Below 1 Ω


Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

B

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

C

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

6.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.
E219772C28
1.427,0.125 1.917,0.417 0.49,0.292 2.906,1.229 3.083,1.667 true 2.771,1.229 2.583,1.667 true 1.563,0.177 1.844,0.333 0.281,0.156 10 false F38 3.042,1.698 3.313,1.885 0.271,0.188 10 false FR 2.354,1.698 2.802,1.896 0.448,0.198 10 false FE&B 0.198,0.094 0.406,0.25 0.208,0.156 10 false *a
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-40 (FR) - F38-39 (FE&B) Always 13.5 to 414.5 Ω



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY)
a.

Disconnect the F28 fuel suction tube with pump and gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-40 (FR) - F28-2 (FS) Always Below 1 Ω
F38-40 (FR) or F28-2 (FS) - Body ground Always 10 kΩ or higher
F38-39 (FE&B) - F28-3 (FE) Always Below 1 Ω
F38-39 (FE&B) or F28-3 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.


Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

9.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

B

REPLACE FUEL SENDER GAUGE ASSEMBLY

C

REPLACE FUEL SENDER GAUGE ASSEMBLY

9.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
a.
E158805C04
1.292,1.313 0.688,1.313 true 1.833,1.219 2.427,0.625 true 0.219,0.104 0.979,0.292 0.76,0.188 10 false *a 2.51,0.542 2.76,0.708 0.25,0.167 10 false FS 0.458,1.229 0.708,1.396 0.25,0.167 10 false FE 0.615,0.656 1.406,0.823 0.792,0.167 10 false *b 0.615,3.094 1.406,3.26 0.792,0.167 10 false *c
*a Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly)
*b Connector A
*c Connector B


Remove the fuel suction tube with pump and gauge assembly.



b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A-2 (FS) - B-2 Always Below 1 Ω
A-3 (FE) - B-1 Always Below 1 Ω


Result:
Result Proceed to
OK A
NG (for 1NR-FE) B
NG (for 2NR-FE) C



A

B

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

C

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY