The meter CPU receives vehicle speed signals from the brake actuator assembly (skid control ECU) via the CAN communication system (CAN V Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (skid control ECU). The brake actuator assembly (skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (skid control ECU) detects vehicle speed signals based on the pulses of the voltage.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (skid control ECU) stores the DTCs. Troubleshoot the Anti-lock Brake System.*1
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1275
If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (skid control ECU) stores the DTCs. Troubleshoot the Vehicle Stability Control System.*2
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1275
*1: w/o VSC
*2: w/ VSC
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before starting the following inspection, check tire size and tire air pressure.
Check if CAN communication DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication DTCs are output. | A |
| CAN communication DTCs are not output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body / Combination Meter / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Speed Meter Operation | Speedometer | OFF, 0, 40, 80, 120, 160, 200 | - |
| Tester Display |
|---|
| Speed Meter Operation |
Speedometer indication is normal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMMIN Made) | B |
| NG (for TMT Made) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed | Min.: 0 km/h
(0 mph) Max.: 255 km/h (158 mph) |
Almost the same as actual vehicle speed | - |
| Tester Display |
|---|
| Vehicle Speed Meter |
Vehicle speed displayed on the GTS is almost the same as the speedometer indication.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for TMMIN Made) | B |
| NG (for TMT Made) | C |
A
B
C
Check if vehicle stability control system or anti-lock brake system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output. (for TMMIN Made) | A |
| DTCs are not output. (for TMT Made) | B |
| DTCs are output. (w/o VSC) | C |
| DTCs are output. (w/ VSC) | D |
A
B
C
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
D