Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2017.10–2018.01
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0084737 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

When a either door is opened and closed (the either door courtesy light switch turns on and off) with the ignition switch ON, or when the ignition switch is turned from off to ON, the rear seat belt warning light in the heater control and accessory assembly*1 or air conditioning control assembly*2 turns on to inform the driver of the rear seat belt condition. If a rear seat belt is fastened or unfastened, the warning light changes to indicate the current rear seat belt condition.

*1: for Manual Air Conditioning System

*2: for Automatic Air Conditioning System


WIRING DIAGRAM

E376644E01
0.865,0.104 2.74,0.573 1.875,0.469 10 false from IG2 Relay*1 or Ignition or Starter Switch Assembly*2 0.906,1.896 1.979,2.281 1.073,0.385 10 false ECU-IG NO.1 2.188,2.146 4.75,2.698 2.563,0.552 10 false Heater Control and Accesory Assembly*3 or Air Conditioning Control Assembly*4 2.563,1.885 2.792,2.146 0.229,0.26 10 false *4 2.563,1.177 2.792,1.438 0.229,0.26 10 false *3 4.125,0.646 4.354,0.906 0.229,0.26 10 false *3 4.146,1.281 4.375,1.542 0.229,0.26 10 false *3 4.135,1.875 4.365,2.135 0.229,0.26 10 false *3 4.552,1.865 4.781,2.125 0.229,0.26 10 false *4 4.552,1.271 4.781,1.531 0.229,0.26 10 false *4 4.552,0.656 4.781,0.917 0.229,0.26 10 false *4 2.885,0.99 3.115,1.25 0.229,0.26 10 false B 2.865,1.708 3.271,1.917 0.406,0.208 10 false IG+ 2.583,0.813 2.813,1.073 0.229,0.26 10 false 8 2.479,0.99 2.969,1.188 0.49,0.198 10 false F154 4.052,0.458 4.542,0.656 0.49,0.198 10 false F154 4.052,1.083 4.542,1.281 0.49,0.198 10 false F154 4.052,1.688 4.542,1.885 0.49,0.198 10 false F154 0.135,8.188 3.125,8.5 2.99,0.313 10 false *1: w/ Smart Entry and Start System 0.135,8.49 3.125,8.802 2.99,0.313 10 false *2: w/o Smart Entry and Start System 2.708,8.188 5.698,8.5 2.99,0.313 10 false *3: for Manual Air Conditioning System 2.708,8.479 5.698,8.792 2.99,0.313 10 false *4: for Automatic Air Conditioning System 5.542,7.823 6.76,8.208 1.219,0.385 10 false Combination Meter Assembly 1.063,4.76 4.063,5.021 3,0.26 10 false Rear Door Courtesy Light Switch Assembly RH 1.083,3.708 4.083,4.042 3,0.333 10 false Rear Door Courtesy Light Switch Assembly LH 1.042,5.844 4.135,6.125 3.094,0.281 10 false Rear Seat Inner with Center Belt Assembly LH 4.458,1.688 4.948,1.885 0.49,0.198 10 false F171 4.458,1.073 4.948,1.271 0.49,0.198 10 false F171 4.448,0.458 4.938,0.656 0.49,0.198 10 false F171 2.469,1.677 2.958,1.875 0.49,0.198 10 false F171 2.583,1.51 2.99,1.719 0.406,0.208 10 false 1 4.583,0.271 4.99,0.479 0.406,0.208 10 false 7 3.646,1.688 4.052,1.896 0.406,0.208 10 false RRID 3.656,0.458 4.063,0.667 0.406,0.208 10 false RLID 3.646,1.083 4.052,1.292 0.406,0.208 10 false RCID 4.583,0.917 4.99,1.125 0.406,0.208 10 false 5 4.594,1.521 5,1.729 0.406,0.208 10 false 4 4.167,0.281 4.573,0.49 0.406,0.208 10 false 4 4.177,0.917 4.583,1.125 0.406,0.208 10 false 3 4.135,1.521 4.542,1.729 0.406,0.208 10 false 12 5.604,0.458 6.01,0.667 0.406,0.208 10 false RLMT 5.604,1.094 6.01,1.302 0.406,0.208 10 false RCMT 5.604,1.688 6.031,1.896 0.427,0.208 10 false RRMT 5.323,0.365 5.729,0.573 0.406,0.208 10 false 12 5.323,1.01 5.729,1.219 0.406,0.208 10 false 11 5.323,1.604 5.729,1.813 0.406,0.208 10 false 10 1.083,3.542 1.573,3.74 0.49,0.198 10 false F33 1.073,4.583 1.563,4.781 0.49,0.198 10 false F34 0.99,7.51 4.083,7.792 3.094,0.281 10 false Rear Seat Inner with Center Belt Assembly RH 1.042,5.677 1.531,5.875 0.49,0.198 10 false F182 1,7.354 1.49,7.552 0.49,0.198 10 false F181 1.729,6.844 2.219,7.042 0.49,0.198 10 false RBR- 2.823,6.844 3.313,7.042 0.49,0.198 10 false RBR+ 2.823,6.344 3.313,6.542 0.49,0.198 10 false CBR+ 1.719,6.344 2.208,6.542 0.49,0.198 10 false CBR- 1.729,5.292 2.219,5.49 0.49,0.198 10 false LBR- 2.844,5.281 3.333,5.479 0.49,0.198 10 false LBR+ 5.615,3.271 6.042,3.479 0.427,0.208 10 false RLCY 5.615,4.344 6.042,4.552 0.427,0.208 10 false RRCY 5.625,5.375 6.031,5.583 0.406,0.208 10 false RLBT 5.615,6.427 6.021,6.635 0.406,0.208 10 false RCSB 5.615,6.906 6.021,7.115 0.406,0.208 10 false RRBT 5.615,7.25 6.021,7.458 0.406,0.208 10 false EP 3.302,3.167 3.729,3.375 0.427,0.208 10 false 1 3.313,4.25 3.74,4.458 0.427,0.208 10 false 1 5.344,3.177 5.833,3.375 0.49,0.198 10 false 32 5.354,4.271 5.844,4.469 0.49,0.198 10 false 33 5.385,6.844 5.875,7.042 0.49,0.198 10 false 7 5.385,6.333 5.875,6.531 0.49,0.198 10 false 8 5.385,5.302 5.875,5.5 0.49,0.198 10 false 9 3.302,6.333 3.792,6.531 0.49,0.198 10 false 3 3.302,6.844 3.792,7.042 0.49,0.198 10 false 5 1.552,6.344 2.042,6.542 0.49,0.198 10 false 2 1.542,6.844 2.031,7.042 0.49,0.198 10 false 4 1.542,5.292 2.031,5.49 0.49,0.198 10 false 2 3.302,5.281 3.729,5.49 0.427,0.208 10 false 1 5.344,7.156 5.75,7.365 0.406,0.208 10 false 21 5.542,7.677 5.948,7.885 0.406,0.208 10 false F38

E386988E02
5.406,3.146 6.604,3.583 1.198,0.438 10 false Combination Meter Assembly 1.156,1.573 3.938,1.833 2.781,0.26 10 false Front Door Courtesy Switch Assembly LH 1.156,2.771 3.938,3.031 2.781,0.26 10 false Front Door Courtesy Switch Assembly RH 5.458,1.094 6.208,1.323 0.75,0.229 10 false PCTY 5.458,2.271 6.208,2.5 0.75,0.229 10 false DCTY 5.417,3 5.854,3.281 0.438,0.281 10 false F38 5.167,2.167 5.917,2.396 0.75,0.229 10 false 30 5.177,1 5.927,1.229 0.75,0.229 10 false 31 3.281,0.99 4.031,1.219 0.75,0.229 10 false 1 3.302,2.146 4.052,2.375 0.75,0.229 10 false 1 1.156,1.417 1.594,1.698 0.438,0.281 10 false F31 1.156,2.594 1.594,2.875 0.438,0.281 10 false F32

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS (REAR LEFT SIDE DOOR AND REAR RIGHT SIDE DOOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Door Driver side door courtesy light switch LH signal OFF or ON ON: Driver side door opened
OFF: Driver side door closed
-
Passenger Side Door Front passenger side door courtesy light switch LH signal OFF or ON ON: Front passenger side opened
OFF: Front passenger side closed
-
Rear Left Side Door Rear door courtesy light switch LH signal OFF or ON ON: Rear door LH opened
OFF: Rear door LH closed
-
Rear Right Side Door Rear door courtesy light switch RH signal OFF or ON ON: Rear door RH opened
OFF: Rear door RH closed
-
Body Electrical > Combination Meter > Data List
Tester Display
Driver Side Door
Passenger Side Door
Rear Left Side Door
Rear Right Side Door
50003 122 121,156,157,158
OK:

The GTS display changes correctly in response to the rear door condition.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (2ND ROW SEAT BELT BUCKLE (R), 2ND ROW SEAT BELT BUCKLE (L) AND 2ND ROW SEAT BELT BUCKLE (C))

NG

12.CHECK HARNESS AND CONNECTOR (DOOR COURTESY LIGHT SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
2.READ VALUE USING GTS (2ND ROW SEAT BELT BUCKLE (R), 2ND ROW SEAT BELT BUCKLE (L) AND 2ND ROW SEAT BELT BUCKLE (C))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear seat belt buckle switch RH OFF or ON OFF: Rear RH seat belt not fastened
ON: Rear RH seat belt fastened
-
2nd-Row Seatbelt Buckle (L) Rear seat belt buckle switch LH OFF or ON OFF: Rear LH seat belt not fastened
ON: Rear LH seat belt fastened
-
2nd-Row Seatbelt Buckle (C) Rear seat center belt buckle switch OFF or ON OFF: Rear seat center belt not fastened
ON: Rear seat center belt fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (R)
2nd-Row Seatbelt Buckle (L)
2nd-Row Seatbelt Buckle (C)
50003 122 74,75,76
OK:

The GTS display changes correctly in response to the rear seat belt condition.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT)

NG

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)
3.PERFORM ACTIVE TEST USING GTS (REAR SEAT BELT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Seat Belt Rear seat belt warning light OFF or ON Confirm that the vehicle is stopped with the engine idling
Body Electrical > Combination Meter > Active Test
Tester Display
Rear Seat Belt
50004 122 100
OK:

Value selected during Active Test is displayed.



Result:
Proceed to
OK
NG



OK

NG

4.SYSTEM CHECK
4.SYSTEM CHECK
a.

Check vehicle type.


Result:
Result Proceed to
for Automatic Air Conditioning System A
for Manual Air Conditioning System B



A

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEATER CONTROL AND ACCESORY ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F171 air conditioning control assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F171-7 (RLID) - F38-12 (RLMT) Always Below 1 Ω
F171-7 (RLID) or F38-12 (RLMT) - Body ground Always 10 kΩ or higher
F171-5 (RCID) - F38-11 (RCMT) Always Below 1 Ω
F171-5 (RCID) or F38-11 (RCMT) - Body ground Always 10 kΩ or higher
F171-4 (RRID) - F38-10 (RRMT) Always Below 1 Ω
F171-4 (RRID) or F38-10 (RRMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK AIR CONDITIONING CONTROL ASSEMBLY (POWER SOURCE)
a.
E376654C01
1.417,0.177 1.885,0.438 0.469,0.26 0.719,0.948 1.125,1.135 true 0.469,0.802 0.927,1 0.458,0.198 10 false IG+ 0.188,0.198 0.646,0.396 0.458,0.198 10 false *a 1.49,0.219 1.948,0.417 0.458,0.198 10 false F171
*a Front view of wire harness connector
(to air conditioning control assembly)


Disconnect the F171 air conditioning control assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F171-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for Sedan) A
OK (for Hatchback) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - HEATER CONTROL AND ACCESORY ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F154 Heater control and accesory assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F154-4 (RLID) - F38-12 (RLMT) Always Below 1 Ω
F154-4 (RLID) or F38-12 (RLMT) - Body ground Always 10 kΩ or higher
F154-3 (RCID) - F38-11 (RCMT) Always Below 1 Ω
F154-3 (RCID) or F38-11 (RCMT) - Body ground Always 10 kΩ or higher
F154-12 (RRID) - F38-10 (RRMT) Always Below 1 Ω
F154-12 (RRID) or F38-10 (RRMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HEATER CONTROL AND ACCESSORY ASSEMBLY (POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HEATER CONTROL AND ACCESSORY ASSEMBLY (POWER SOURCE)
a.
E376654C02
1.427,0.198 1.917,0.458 0.49,0.26 2.646,0.781 2.198,1.125 true 0.146,0.073 0.458,0.271 0.313,0.198 10 false *a 2.688,0.635 3,0.833 0.313,0.198 10 false B 1.51,0.24 1.958,0.469 0.448,0.229 10 false F154
*a Front view of wire harness connector
(to air conditioning control assembly)


Disconnect the F154 air conditioning control assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F154-8 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for Sedan) A
OK (for Hatchback) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F181 rear seat inner with center belt assembly RH connector.


c.

Disconnect the F182 rear seat inner with center belt assembly LH connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Rear seat inner with center belt assembly RH
Tester Connection Condition Specified Condition
F181-3 (CBR+) - F38-8 (RCSB) Always Below 1 Ω
F181-2 (CBR-) - Body ground Always Below 1 Ω
F181-3 (CBR+) or F38-8 (RCSB) - Body ground Always 10 kΩ or higher
F181-5 (RBR+) - F38-7 (RRBT) Always Below 1 Ω
F181-4 (RBR-) - Body ground Always Below 1 Ω
F181-5 (RBR+) or F38-7 (RRBT) - Body ground Always 10 kΩ or higher

Rear seat inner with center belt assembly LH
Tester Connection Condition Specified Condition
F182-1 (LBR+) - F38-9 (RLBT) Always Below 1 Ω
F182-2 (LBR-) - Body ground Always Below 1 Ω
F182-1 (LBR+) or F38-9 (RLBT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH
a.

Remove the rear seat inner with center belt assembly RH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for RH Side)>REMOVAL


b.

Inspect the rear seat inner with center belt assembly RH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for RH Side)>INSPECTION


Result:
Proceed to
OK
NG



OK

11.REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH

11.REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


Result:
Proceed to
OK
NG



OK

NG

12.CHECK HARNESS AND CONNECTOR (DOOR COURTESY LIGHT SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F31 front door courtesy light switch assembly LH connector.


c.

Disconnect the F32 front door courtesy light switch assembly RH connector.


d.

Disconnect the F33 rear door courtesy light switch assembly LH connector.


e.

Disconnect the F34 rear door courtesy light switch assembly RH connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Front door courtesy light switch assembly LH
Tester Connection Condition Specified Condition
F31-1 - F38-31 (PCTY) Always Below 1 Ω
F31-1 or F38-31 (PCTY) - Body ground Always 10 kΩ or higher

Front door courtesy light switch assembly RH
Tester Connection Condition Specified Condition
F32-1 - F38-30 (DCTY) Always Below 1 Ω
F32-1 or F38-30 (DCTY) - Body ground Always 10 kΩ or higher

Rear door courtesy light switch assembly LH
Tester Connection Condition Specified Condition
F33-1 - F38-32 (RLCY) Always Below 1 Ω
F33-1 or F38-32 (RLCY) - Body ground Always 10 kΩ or higher

Rear door courtesy light switch assembly RH
Tester Connection Condition Specified Condition
F34-1 - F38-33 (RRCY) Always Below 1 Ω
F34-1 or F38-33 (RRCY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY
a.

Remove the front door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY

NG

REPLACE FRONT DOOR COURTESY LAMP SWITCH ASSEMBLY

14.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY
a.

Remove the rear door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY