Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
3.PLACE FRONT WHEELS FACING STRAIGHT AHEAD
4.SECURE STEERING WHEEL
55606
5.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55480D
6.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
55432B
7.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)
73900
8.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
45882
9.REMOVE STEERING COLUMN PROTECTOR BRACKET
Remove the 2 nuts and steering column protector bracket from the steering column assembly.
45259A
10.REMOVE COLUMN HOLE COVER SILENCER SHEET
45209
11.DISCONNECT STEERING SLIDING YOKE SUB-ASSEMBLY
31301A
12.REMOVE CLUTCH PEDAL SPRING
Remove the clutch pedal spring from the clutch pedal support sub-assembly and clutch pedal sub-assembly.
31453
13.DISCONNECT CLUTCH MASTER CYLINDER PUSH ROD CLEVIS
Remove the clip from the push rod clevis pin.
Remove the push rod clevis pin and disconnect the clutch master cylinder push rod clevis from the clutch pedal sub-assembly.
55107A
14.REMOVE CLUTCH PEDAL SUPPORT SUB-ASSEMBLY
Disconnect the connector from the clutch start switch assembly.
Disengage the clamp from the clutch pedal support sub-assembly.
Remove the 2 bolts, 2 nuts and clutch pedal support sub-assembly from the body and clutch master cylinder assembly.
84520
15.REMOVE CLUTCH START SWITCH ASSEMBLY
Remove the nut and clutch start switch assembly from the clutch pedal support sub-assembly.
To prevent damage to the clutch start switch assembly, make sure not to rotate it during removal.
31301F
16.REMOVE CLUTCH PEDAL STOPPER BOLT
Loosen the lock nut and remove the clutch pedal stopper bolt from the clutch pedal support sub-assembly.
31301
17.REMOVE CLUTCH PEDAL SUB-ASSEMBLY
Remove the bolt, nut and clutch pedal sub-assembly from the clutch pedal support sub-assembly.
Turn the nut while holding the bolt.
31324A
18.REMOVE CLUTCH PEDAL SHAFT COLLAR
| *1 | Clutch Pedal Spring Bush |
| *2 | Clutch Pedal Shaft Collar |
Remove the 2 clutch pedal spring bushes and clutch pedal shaft collar from the clutch pedal sub-assembly.
31301B
19.REMOVE NO. 1 CLUTCH PEDAL CUSHION
Remove the No. 1 clutch pedal cushion from the clutch pedal sub-assembly.
31301C
20.REMOVE CLUTCH PEDAL BUSH
Secure the clutch pedal sub-assembly in a vise between aluminum plates.
Do not overtighten the vise.
Using an 8 mm hexagon socket wrench and hammer, remove the clutch pedal bush from the clutch pedal sub-assembly.
31322
21.REMOVE CLUTCH PEDAL STOPPER
Remove the clutch pedal stopper from the clutch pedal sub-assembly.
31321
22.REMOVE CLUTCH PEDAL PAD
Remove the clutch pedal pad from the clutch pedal sub-assembly.