Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1830/57  Short in Curtain Shield Squib RH Circuit  B1831/57  Open in Curtain Shield Squib RH Circuit  B1832/57  Short to GND in Curtain Shield Squib RH Circuit  B1833/57  Short to B+ in Curtain Shield Squib RH Circuit  


DESCRIPTION

The curtain shield squib RH circuit consists of the airbag ECU assembly and curtain shield airbag assembly RH.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1830/57 Short in Curtain Shield Squib RH Circuit
·

The airbag ECU assembly detects a line short in the curtain shield squib RH circuit during primary check.

·

Curtain shield squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Airbag ECU assembly


Applies to check mode
B1831/57 Open in Curtain Shield Squib RH Circuit
·

The airbag ECU assembly detects an open in the curtain shield squib RH circuit.

·

Curtain shield squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Airbag ECU assembly


Applies to check mode
B1832/57 Short to GND in Curtain Shield Squib RH Circuit
·

The airbag ECU assembly detects a short to ground in the curtain shield squib RH circuit.

·

Curtain shield squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Airbag ECU assembly


Applies to check mode
B1833/57 Short to B+ in Curtain Shield Squib RH Circuit
·

The airbag ECU assembly detects a short to B+ in the curtain shield squib RH circuit.

·

Curtain shield squib RH malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

No. 2 instrument panel wire

·

Curtain shield airbag assembly RH (Curtain shield squib RH)

·

Airbag ECU assembly


Applies to check mode

WIRING DIAGRAM

C391299E01
1.979,1.771 2.594,1.969 0.615,0.198 10 false ICR+ 2.031,2.542 2.646,2.74 0.615,0.198 10 false ICR- 2.396,1.781 2.552,1.979 0.156,0.198 10 false 1 2.406,2.573 2.563,2.771 0.156,0.198 10 false 2 0.51,3.24 0.823,3.438 0.313,0.198 10 false T1 0.51,3.417 2.698,3.865 2.188,0.448 10 false Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH) 4.75,1.875 5.365,2.073 0.615,0.198 10 false ICR+ 4.74,2.688 5.354,2.885 0.615,0.198 10 false ICR- 4.531,1.75 4.688,1.948 0.156,0.198 10 false 9 4.479,2.573 4.823,2.729 0.344,0.156 10 false 10 3.385,1.896 3.844,2.094 0.458,0.198 10 false FT1 3.396,2.688 3.854,2.885 0.458,0.198 10 false FT1 3.417,1.677 3.573,1.875 0.156,0.198 10 false 1 3.438,2.479 3.594,2.677 0.156,0.198 10 false 2 4.708,3.896 5.323,4.094 0.615,0.198 10 false F120 4.729,4.083 6.167,4.417 1.438,0.333 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK CONNECTORS
a.
C391287C01
0.354,1.313 0.656,0.813 false 1.073,1.323 1.302,0.844 false 1.719,1.323 1.906,0.854 false 0.615,0.635 0.927,0.833 0.313,0.198 10 false *1 2.615,1.031 2.927,1.229 0.313,0.198 10 false *2 2.24,1.323 2.396,1.521 0.156,0.198 10 false A 1.927,1.323 2.083,1.521 0.156,0.198 10 false B 1.458,1.323 1.615,1.521 0.156,0.198 10 false C 1.302,1.323 1.458,1.521 0.156,0.198 10 false D 0.854,1.313 1.01,1.51 0.156,0.198 10 false E 0.552,1.313 0.833,1.521 0.281,0.208 10 false F 1.24,0.646 1.552,0.844 0.313,0.198 10 false *3 1.875,0.656 2.188,0.854 0.313,0.198 10 false *4
*1 Curtain Shield Airbag Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the curtain shield airbag assembly RH and airbag ECU assembly. Also check that the connectors that link the instrument panel wire and No. 2 instrument panel wire are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the curtain shield airbag assembly RH and airbag ECU assembly. Also disconnect the instrument panel wire from the No. 2 instrument panel wire.


e.

Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the No. 2 instrument panel wire connector (on the curtain shield airbag assembly RH side) is not damaged.

OK:

The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.



g.

Check that the short spring for the instrument panel wire and No. 2 instrument panel wire with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)

NG

REPLACE INSTRUMENT PANEL WIRE

2.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)
a.
C391288C01
0.323,2.354 0.75,2.594 0.427,0.24 0.521,0.927 0.75,0.448 false 1.813,2.323 2.094,2.219 false 0.708,0.208 1.021,0.406 0.313,0.198 10 false *1 2.604,0.625 2.917,0.823 0.313,0.198 10 false *2 2.24,0.927 2.396,1.125 0.156,0.198 10 false A 2.083,0.938 2.24,1.135 0.156,0.198 10 false B 1.625,0.938 1.781,1.135 0.156,0.198 10 false C 1.469,0.938 1.625,1.135 0.156,0.198 10 false D 1.01,0.938 1.219,1.104 0.208,0.167 10 false E 0.688,0.948 0.844,1.146 0.156,0.198 10 false F 0.323,1.813 0.635,2.01 0.313,0.198 10 false *a 0.458,2.385 0.771,2.583 0.313,0.198 10 false T1 2.125,2.115 2.583,2.313 0.458,0.198 10 false SST
*1 Curtain Shield Airbag Assembly RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Curtain Shield Airbag Assembly RH)


Connect the instrument panel wire to the No. 2 instrument panel wire and airbag ECU assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E.

CAUTION:

Never connect a tester to the curtain shield airbag assembly RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output.


HINT:

Codes other than DTCs B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.



h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.


Result:
Result Proceed to
OK (for Sedan) A
OK (for Hatchback) B
NG C



A

B

C

3.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY CIRCUIT
3.CHECK CURTAIN SHIELD AIRBAG ASSEMBLY CIRCUIT
a.
C391290C01
0.417,2.51 0.823,2.719 0.406,0.208 0.448,0.927 0.625,0.479 false 1.188,2.052 1.573,2.208 true 1.729,2.208 2.104,2.052 true 0.583,0.281 0.896,0.479 0.313,0.198 10 false *1 2.74,0.594 3.052,0.792 0.313,0.198 10 false *2 0.365,1.813 0.677,2.01 0.313,0.198 10 false *a 0.542,2.542 0.854,2.74 0.313,0.198 10 false T1 0.927,1.885 1.542,2.083 0.615,0.198 10 false ICR+ 2.083,1.854 2.698,2.052 0.615,0.198 10 false ICR- 2.354,0.938 2.51,1.135 0.156,0.198 10 false A 2.021,0.938 2.177,1.135 0.156,0.198 10 false B 1.552,0.938 1.708,1.135 0.156,0.198 10 false C 1.396,0.938 1.552,1.135 0.156,0.198 10 false D 0.938,0.938 1.094,1.135 0.156,0.198 10 false E 0.635,0.927 0.792,1.125 0.156,0.198 10 false F
*1 Curtain Shield Airbag Assembly RH
*2 Airbag ECU Assembly
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly )


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect SST from connector E.


d.

Disconnect the instrument panel wire from the airbag ECU assembly.


e.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T1-2 (ICR-) - Body ground Ignition switch ON Below 1 V
T1-1 (ICR+) - Body ground Ignition switch ON Below 1 V




f.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 (ICR-) - T1-1 (ICR+) Always Below 1 Ω




g.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 (ICR-) - Body ground Always 1 MΩ or higher
T1-1 (ICR+) - Body ground Always 1 MΩ or higher




h.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 (ICR-) - T1-1 (ICR+) Always 1 MΩ or higher




Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

4.CHECK INSTRUMENT PANEL WIRE
4.CHECK INSTRUMENT PANEL WIRE
a.
C391298C01
0.469,2.271 0.875,2.479 0.406,0.208 0.396,0.927 0.583,0.479 false 1.115,0.927 1.25,0.49 false 1.875,0.938 2.021,0.531 false 1.25,2.823 1.604,2.531 true 1.802,2.531 2.146,2.833 true 0.531,0.302 0.844,0.5 0.313,0.198 10 false *1 2.771,0.635 3.083,0.833 0.313,0.198 10 false *2 1.188,0.333 1.5,0.531 0.313,0.198 10 false *3 1.979,0.313 2.292,0.51 0.313,0.198 10 false *4 0.365,1.792 0.677,1.99 0.313,0.198 10 false *a 0.563,2.281 1.021,2.479 0.458,0.198 10 false FT1 1.031,2.844 1.646,3.042 0.615,0.198 10 false ICR+ 2.063,2.854 2.677,3.052 0.615,0.198 10 false ICR- 2.427,0.938 2.583,1.135 0.156,0.198 10 false A 2.083,0.927 2.354,1.198 0.271,0.271 10 false B 1.635,0.938 1.792,1.135 0.156,0.198 10 false C 1.313,0.948 1.469,1.146 0.156,0.198 10 false D 0.854,0.948 1.01,1.146 0.156,0.198 10 false E 0.531,0.948 0.688,1.146 0.156,0.198 10 false F
*1 Curtain Shield Airbag Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


Restore the released activation prevention mechanism of connector B to the original condition.


b.

Disconnect the No. 2 instrument panel wire from the instrument panel wire.


c.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
FT1-1 (ICR+) - Body ground Ignition switch ON Below 1 V
FT1-2 (ICR-) - Body ground Ignition switch ON Below 1 V




d.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FT1-1 (ICR+) - FT1-2 (ICR-) Always Below 1 Ω




e.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FT1-1 (ICR+) - Body ground Always 1 MΩ or higher
FT1-2 (ICR-) - Body ground Always 1 MΩ or higher




f.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
FT1-1 (ICR+) - FT1-2 (ICR-) Always 1 MΩ or higher




g.

Restore the released activation prevention mechanism of connector B to the original condition.


Result:
Proceed to
OK
NG



OK

5.CHECK NO. 2 INSTRUMENT PANEL WIRE

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK NO. 2 INSTRUMENT PANEL WIRE
a.
C391291C01
0.427,2.552 0.844,2.75 0.417,0.198 0.365,0.927 0.521,0.51 false 1.125,0.927 1.271,0.51 false 1.875,0.938 2.031,0.542 false 1.26,2.073 1.573,2.198 true 1.719,2.198 2.073,2.083 true 2.427,0.938 2.583,1.135 0.156,0.198 10 false A 2.083,0.938 2.24,1.135 0.156,0.198 10 false B 1.635,0.938 1.792,1.135 0.156,0.198 10 false C 1.313,0.948 1.469,1.146 0.156,0.198 10 false D 0.854,0.938 1.01,1.135 0.156,0.198 10 false E 0.542,0.938 0.698,1.135 0.156,0.198 10 false F 0.51,0.323 0.823,0.521 0.313,0.198 10 false *1 2.813,0.615 3.125,0.813 0.313,0.198 10 false *2 1.24,0.302 1.552,0.5 0.313,0.198 10 false *3 1.979,0.323 2.292,0.521 0.313,0.198 10 false *4 0.375,1.844 0.688,2.042 0.313,0.198 10 false *a 0.563,2.573 0.875,2.771 0.313,0.198 10 false T1 1.01,1.865 1.625,2.063 0.615,0.198 10 false ICR+ 2,1.865 2.615,2.063 0.615,0.198 10 false ICR-
*1 Curtain Shield Airbag Assembly RH
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly )


Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) battery terminal.


ii.

Turn the ignition switch to ON.


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
T1-2 (ICR-) - Body ground Ignition switch ON Below 1 V
T1-1 (ICR+) - Body ground Ignition switch ON Below 1 V




b.

Check for an open in the circuit.

i.

Turn the ignition switch off.


ii.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 (ICR-) - T1-1 (ICR+) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 (ICR-) - Body ground Always 1 MΩ or higher
T1-1 (ICR+) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T1-2 (ICR-) - T1-1 (ICR+) Always 1 MΩ or higher




e.

Restore the released activation prevention mechanism of connector D to the armed condition.


Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

REPLACE NO. 2 INSTRUMENT PANEL WIRE

6.CHECK DTC
a.

Restore the released activation prevention mechanism of connector B to the original condition.


b.
C391289C01
0.552,1.313 0.813,0.844 false 0.813,0.646 1.125,0.844 0.313,0.198 10 false *1 2.458,1.031 2.771,1.229 0.313,0.198 10 false *2 2.083,1.313 2.24,1.51 0.156,0.198 10 false A 1.927,1.313 2.083,1.51 0.156,0.198 10 false B 1.469,1.323 1.625,1.521 0.156,0.198 10 false C 1.313,1.323 1.469,1.521 0.156,0.198 10 false D 0.854,1.313 1.01,1.51 0.156,0.198 10 false E 0.698,1.323 0.854,1.521 0.156,0.198 10 false F
*1 Curtain Shield Airbag Assembly RH
*2 Airbag ECU Assembly


Connect the connectors to the curtain shield airbag assembly RH and airbag ECU assembly.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output.


HINT:

Codes other than DTCs B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG