When the wireless operation can be used to lock and unlock the doors, communication between the door control receiver and certification ECU (smart key ECU assembly) is normal. If the entry lock and unlock functions do not operate, the entry cancel function may be set through the customize function, there may be communication problems between the electrical key transmitter sub-assembly and vehicle, or there may be wave interference.
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output.
Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
When the door control switch on the power window regulator master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Auto Entry Cancel SW | Entry cancel function setting | ON or OFF | Mode status displayed
ON: Smart entry and start system canceled OFF: Smart entry and start system not canceled |
The default setting for the entry cancel function is OFF. If the customer requests that the smart entry and start system functions (locking and unlocking the doors while carrying the electrical key transmitter sub-assembly, etc.) be canceled, the setting can be changed through the customize function.* |
| Tester Display |
|---|
| Auto Entry Cancel SW |
If the Data List cannot be read, check the value by performing manual operation of the customize function.
| Result | Proceed to |
|---|---|
| Entry door lock function cancel is OFF | A |
| Entry door lock function cancel is ON | B |
A
B
Move the electrical key transmitter sub-assembly as described below and perform the operation inspection.
When the electrical key transmitter sub-assembly is brought near the center pillar LH, center pillar RH or electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom. (for TMMIN Made)
When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly LH or electrical key antenna (outside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom. (for TMT Made)
The transmitting wave of the wireless function and entry function are the same, but the wave logic is different. As a result, it is possible that only the wireless function or only the entry function is affected by wave interference.
for Sedan
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform a driver door entry lock and unlock operation check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.
| *a | Approximately 0.3 m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the No. 3 indoor electrical key antenna assembly (luggage compartment) and perform a luggage compartment door open function check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not be possible.
for Hatchback
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform a driver door entry lock and unlock operation check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.
| *a | Approximately 0.7 m (2.30 ft.) |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the No. 3 indoor electrical key antenna assembly (back door) and perform a back door open function check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not be possible.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
If wave interference seems to be the likely cause of the problem, ask the customer if the problem occurs in specific locations.
Move the vehicle to a different location, perform the following procedure and check if the symptoms can be reproduced.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| All operation checks fail (for TMMIN Made) | A |
| All operation checks fail (for TMT Made) | B |
| All operation checks are normal | C |
| Some operation checks are normal | D |
A
B
C
D
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
Check the No. 1 indoor electrical key antenna assembly (center pillar LH):
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the No. 3 indoor electrical key antenna assembly (luggage compartment):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the No. 3 indoor electrical key antenna assembly (luggage compartment), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (center pillar RH) and No. 1 indoor electrical key antenna assembly (center pillar LH):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor):
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| Result | Proceed to |
|---|---|
| All diagnostic mode inspections fail | A |
| Some diagnostic mode inspections fail (door) | B |
| Some diagnostic mode inspections fail (interior) | C |
| Some diagnostic mode inspections fail (luggage compartment) | D |
| All diagnostic mode inspections are normal | E |
A
B
C
D
E
Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.
| Result | Proceed to |
|---|---|
| Another registered electrical key transmitter sub-assembly is not available | A |
| Another registered electrical key transmitter sub-assembly is available | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the entry lock function.
Entry lock function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
for Sedan
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (for driver door)
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (outside luggage compartment)
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment)check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
for Hatchback
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (for driver door)
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly RH, check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| *a | Approximately 0.7 m (2.30 ft.) |
Check the electrical key antenna (outside luggage compartment)
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Wireless door lock buzzer sounds.
| Result | Proceed to |
|---|---|
| All diagnostic mode inspections fail | A |
| Some diagnostic mode inspections fail (door) | B |
| Some diagnostic mode inspections fail (luggage compartment) (for Sedan) | C |
| Some diagnostic mode inspections fail (back door) (for Hatchback) | D |
| All diagnostic mode inspections are normal | E |
A
B
C
D
E
Check if there is another electrical key transmitter sub-assembly available that is already registered to the vehicle.
| Result | Proceed to |
|---|---|
| Another registered electrical key transmitter sub-assembly is not available | A |
| Another registered electrical key transmitter sub-assembly is available | B |
A
B
Register a new electrical key transmitter sub-assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check the operation of the entry lock function.
Entry lock function operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG