The theft deterrent system is unset when the IG signal and engine speed signal are input to the body computer for 2 seconds or more continuously.
The engine speed signal is sent from the ECM to the body computer. For this reason, if there is an abnormality in an ECU or wire harness, the system may not function correctly.
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the driver side junction block assembly connectors.
| *a | Front view of wire harness connector
(to Driver Side Junction Block Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 6O-1 - Body ground | Always | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Door Control Battery) | B |
| NG (w/o Door Control Battery) | C |
A
B
C
Disconnect the driver side junction block assembly connectors.
| *a | Front view of wire harness connector
(to Driver Side Junction Block Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 6F-1 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the body computer.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Disconnect the driver side junction block assembly connectors.
Measure the resistance according the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 6O-1 - MB-6 (BECU) | Always | Below 1 Ω |
| 6F-1 - MB-7 (IG) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the body computer to the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>INSTALLATION
Reconnect the body computer connector.
Reconnect the 6O, 6F and 6J driver side junction block assembly connectors.
Remove the driver side junction block assembly with connectors still connected.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
| *a | Component with harness connected
(Body Computer) |
Check the engine speed input signal waveform at the terminal of body computer.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F52-13 (TACH) - Body ground | Engine stopped | No pulse generation |
| F52-13 (TACH) - Body ground | Engine running | Pulse generation |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ Smart Entry and Start System) | B |
| NG (w/o Smart Entry and Start System) | C |
A
B
C
Disconnect the F52 body computer connector.
Disconnect the F131 ECM connector.
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F52-13 (TACH) - F131-16 (NEO) | Always | Below 1 Ω |
| F52-13 (TACH) - F43-6 (NE) | Always | Below 1 Ω |
| F131-16 (NEO) - F43-6 (NE) | Always | Below 1 Ω |
| F52-13 (TACH) or F131-16 (NEO) - Body ground | Always | 10 kΩ or higher |
| F52-13 (TACH) or F43-6 (NE) - Body ground | Always | 10 kΩ or higher |
| F131-16 (NEO) or F43-6 (NE) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F52 body computer connector.
Reconnect the F131 ECM connector.
Reconnect the F43 certification ECU (smart key ECU assembly) connector.
| *a | Component with harness connected
(ECM) |
Check the engine speed input signal waveform at the terminal of ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-16 (NEO) - Body ground | Engine stopped | No pulse generation |
| F131-16 (NEO) - Body ground | Engine running | Pulse generation |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Disconnect the F52 body computer connector.
Disconnect the F131 ECM connector.
| *a | Front view of wire harness connector
(to ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-16 (NEO) - Body ground | Engine stopped | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NR-FE) | B |
| NG (for 2NR-FE) | C |
A
B
C
Replace the certification ECU (smart key ECU assembly) with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the F52 body computer connector.
Reconnect the F131 ECM connector.
Reconnect the F43 certification ECU (smart key ECU assembly) connector.
| *a | Component with harness connected
(ECM) |
Check the engine speed input signal waveform at the terminal of ECM.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-16 (NEO) - Body ground | Engine stopped | No pulse generation |
| F131-16 (NEO) - Body ground | Engine running | Pulse generation |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NR-FE) | B |
| NG (for 2NR-FE) | C |
A
B
C
Disconnect the F52 body computer connector.
Disconnect the F131 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F52-13 (TACH) - F131-16 (NEO) | Always | Below 1 Ω |
| F52-13 (TACH) or F131-16 (NEO) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for 1NR-FE) | A |
| OK (for 2NR-FE) | B |
| NG | C |
A
B
C