73480
1.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for Sedan)
| *a | Unlock |
| *b | Lock |
Check the angle of inclination required to lock the retractor.
Gently incline the retractor from its initial position. Check that the belt does not lock when the retractor is inclined 15° or less in any direction. Also, check that the belt locks when the inclination of the retractor is 45° or more.
Do not disassemble the retractor.
If the operation is not as specified, replace the rear seat inner with center belt assembly LH.
73480
2.INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for Sedan)
Engage the guide to install the rear seat inner with center belt assembly LH.
Install the bolt.
Connect the floor anchor part of the rear seat inner with center belt assembly LH with the bolt.
Check that the ELR locks.
Perform the check with the rear seat inner with center belt assembly LH installed.
With the belt installed, check that the belt locks when it is pulled out quickly.
If the operation is not as specified, replace the rear seat inner with center belt assembly LH.
Remove the bolt to disconnect the floor anchor part of the front seat outer belt assembly.
64274
3.INSTALL NO. 1 ROOM PARTITION TRIM PAD (for Sedan)
for Separate Seat Type:
Click hereVehicle Interior>SEAT BELT>CHILD RESTRAINT SEAT ANCHOR BRACKET(for Sedan)>INSTALLATION
64330D
4.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Sedan)
62472A
5.INSTALL ROOF SIDE INNER GARNISH LH (for Sedan)
62471A
6.INSTALL ROOF SIDE INNER GARNISH RH (for Sedan)
Use the same procedure as for the LH side.
62552F
7.INSTALL REAR SEAT SIDE GARNISH LH (for Sedan)
62551F
8.INSTALL REAR SEAT SIDE GARNISH RH (for Sedan)
Use the same procedure as for the LH side.
73370
9.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (for Sedan)
73360
10.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH (for Sedan)
Use the same procedure as for the LH side.
62332A
11.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Sedan)
Connect the rear door opening trim weatherstrip LH.
62331A
12.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Sedan)
Use the same procedure as for the LH side.
67918A
13.INSTALL REAR DOOR SCUFF PLATE LH (for Sedan)
67917A
14.INSTALL REAR DOOR SCUFF PLATE RH (for Sedan)
Use the same procedure as for the LH side.
15.INSTALL REAR SEAT ASSEMBLY (for Sedan)
for Fixed Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Fixed Seat Type)>INSTALLATION
for Separate Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Seat Type)>INSTALLATION
81006
16.INSTALL CENTER STOP LIGHT SET (for Sedan)
73480
17.INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for Hatchback)
w/o Seat Belt Warning System:
| *a | Convex |
| *b | Arrow Mark |
Install the rear seat inner with center belt assembly LH with the bolt.
Install the rear seat inner with center belt assembly LH with the arrow mark on the anchor part facing the front of the vehicle.
Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the convex of the floor panel.
w/ Seat Belt Warning System:
| *a | Convex |
| *b | Arrow Mark |
Install the rear seat inner with center belt assembly LH with the bolt.
Install the rear seat inner with center belt assembly LH with the arrow mark on the anchor part facing the front of the vehicle.
Do not allow the anchor part of the rear seat inner with center belt assembly LH to overlap the convex of the floor panel.
Connect the connector.
Install the wiring harness protector.
18.INSTALL REAR SEAT CUSHION ASSEMBLY (for Hatchback)
for Fold Down Seat Type
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Fold Down Seat Type)>INSTALLATION
for Separate Seat Type
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Seat Type)>INSTALLATION