Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2018.01
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit (LHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Combination meter assembly

·

Airbag ECU assembly

·

Brake actuator assembly

·

ECM

·

Certification ECU (smart key ECU assembly)*1

·

Air conditioning amplifier assembly

·

No. 1 CAN junction connector

·

Steering sensor*2

·

Power steering ECU assembly

·

No. 23 CAN junction connector



*1: w/ Smart Entry and Start System

*2: w/ VSC


WIRING DIAGRAM

C387581E03
0.167,0.167 1.083,0.365 0.917,0.198 10 false V Bus: 3.354,0.365 3.99,0.615 0.635,0.25 10 false 120 Ω 5.75,5.375 6.385,5.625 0.635,0.25 10 false F12 4.583,0.708 5.219,0.958 0.635,0.25 10 false ECM 4.031,0.979 4.667,1.229 0.635,0.25 10 false CANH 4.042,1.833 4.677,2.083 0.635,0.25 10 false BE 2.906,1.833 3.542,2.083 0.635,0.25 10 false W 5.823,3.125 6.458,3.375 0.635,0.25 10 false CANL 2.031,2.646 2.667,2.896 0.635,0.25 10 false W 2.063,2.26 2.698,2.51 0.635,0.25 10 false B 5.094,3.063 5.729,3.313 0.635,0.25 10 false W 5.125,2.667 5.76,2.917 0.635,0.25 10 false L 2.948,1.188 3.583,1.438 0.635,0.25 10 false 14 3.969,1.177 4.604,1.427 0.635,0.25 10 false 13 2.958,2.146 3.594,2.396 0.635,0.25 10 false 14 3.99,2.135 4.625,2.385 0.635,0.25 10 false 3 2.729,2.344 3.365,2.594 0.635,0.25 10 false 4 2.656,2.698 3.292,2.948 0.635,0.25 10 false 15 4.271,3.115 4.906,3.365 0.635,0.25 10 false 18 4.302,2.75 4.938,3 0.635,0.25 10 false 7 1.458,2.333 2.094,2.583 0.635,0.25 10 false 13 1.458,2.708 2.094,2.958 0.635,0.25 10 false 22 1.427,4.521 2.063,4.771 0.635,0.25 10 false 12 1.427,4.031 2.063,4.281 0.635,0.25 10 false 11 2.719,4.042 3.354,4.292 0.635,0.25 10 false 8 2.667,4.51 3.302,4.76 0.635,0.25 10 false 19 4.26,4.51 4.896,4.76 0.635,0.25 10 false 10 5.635,4.51 6.271,4.76 0.635,0.25 10 false 7 5.604,2.75 6.24,3 0.635,0.25 10 false 40 5.594,3.125 6.229,3.375 0.635,0.25 10 false 18 5.646,4.885 6.281,5.135 0.635,0.25 10 false 8 4.271,4.896 4.906,5.146 0.635,0.25 10 false 21 1.448,6.104 2.083,6.354 0.635,0.25 10 false 3 1.448,6.49 2.083,6.74 0.635,0.25 10 false 2 2.656,6.479 3.292,6.729 0.635,0.25 10 false 20 2.719,6.115 3.354,6.365 0.635,0.25 10 false 9 4.302,6.25 4.938,6.5 0.635,0.25 10 false 1 4.26,6.635 4.896,6.885 0.635,0.25 10 false 12 5.615,6.271 6.25,6.521 0.635,0.25 10 false 6 5.688,6.656 6.323,6.906 0.635,0.25 10 false 14 5.823,4.906 6.458,5.156 0.635,0.25 10 false CANL 1,6.49 1.635,6.74 0.635,0.25 10 false CANL 6,6.688 6.635,6.938 0.635,0.25 10 false CANL 2.698,0.969 3.333,1.219 0.635,0.25 10 false CANL 0.969,2.333 1.604,2.583 0.635,0.25 10 false CANH 5.813,2.76 6.448,3.01 0.635,0.25 10 false CANH 5.823,4.521 6.458,4.771 0.635,0.25 10 false CANH 0.979,6.104 1.615,6.354 0.635,0.25 10 false CANH 5.833,6.344 6.469,6.594 0.635,0.25 10 false CANH 1,2.719 1.635,2.969 0.635,0.25 10 false CANL 1.104,4.042 1.74,4.292 0.635,0.25 10 false TX+ 1.135,4.51 1.771,4.76 0.635,0.25 10 false TX- 0.281,4.969 1.333,5.135 1.052,0.167 10 false F3*1, F124*2 0.25,3.208 0.885,3.458 0.635,0.25 10 false F21 4.583,0.542 5.219,0.792 0.635,0.25 10 false F130 5.344,3.563 5.979,3.813 0.635,0.25 10 false F44 6.052,6.958 6.688,7.208 0.635,0.25 10 false F16 0.24,6.979 0.875,7.229 0.635,0.25 10 false F147 2.896,7.25 3.531,7.5 0.635,0.25 10 false F62 0.24,3.375 1.948,3.646 1.708,0.271 10 false Airbag ECU Assembly 0.302,5.135 1.865,5.604 1.563,0.469 10 false Air Conditioning Amplifier Assembly 5.323,3.719 7.115,4.219 1.792,0.5 10 false Certification ECU (Smart Key ECU Assembly)*3 5.75,5.521 7.031,5.938 1.281,0.417 10 false Power Steering ECU Assembly 6.052,7.115 6.688,7.365 0.635,0.25 10 false DLC3 2.896,7.417 4.156,7.906 1.26,0.49 10 false No. 1 CAN Junction Connector 0.25,7.135 1.823,7.427 1.573,0.292 10 false Steering sensor*4 0.083,7.583 2.938,7.802 2.854,0.219 10 false *1: for Automatic Air Conditioning System 0.083,7.917 2.927,8.146 2.844,0.229 10 false *2: for Manual Air Conditioning System 0.083,8.25 2.719,8.458 2.635,0.208 10 false *3: w/ Smart Entry and Start System 0.854,8.99 2.75,9.302 1.896,0.313 10 false : CAN Main Bus Line (CANH) 0.865,9.396 2.76,9.708 1.896,0.313 10 false : CAN Main Bus Line (CANL) 3.979,8.979 5.875,9.292 1.896,0.313 10 false : CAN Branch Line (CANH) 3.99,9.385 5.885,9.698 1.896,0.313 10 false : CAN Branch Line (CANL) 3.115,8.167 5.01,8.479 1.896,0.313 10 false X: Suspected Area 5.115,4.448 5.75,4.698 0.635,0.25 10 false B 5.094,4.833 5.729,5.083 0.635,0.25 10 false W 4.917,6.198 5.552,6.448 0.635,0.25 10 false GR 4.948,6.583 5.583,6.833 0.635,0.25 10 false W 2.042,6.417 2.677,6.667 0.635,0.25 10 false W 2.063,6.063 2.698,6.313 0.635,0.25 10 false R 2.385,4.458 3.052,4.708 0.667,0.25 10 false W 2.406,3.979 3.073,4.229 0.667,0.25 10 false V 0.083,8.583 2.719,8.792 2.635,0.208 10 false *4: w/ VSC

E373645E13
3.125,1.146 3.74,1.344 0.615,0.198 10 false F174 3.896,1.146 4.51,1.344 0.615,0.198 10 false F174 3.885,2.146 4.5,2.344 0.615,0.198 10 false F174 3.115,2.146 3.729,2.344 0.615,0.198 10 false F174 4.396,1.417 5.01,1.615 0.615,0.198 10 false A60 4.396,1.771 5.01,1.969 0.615,0.198 10 false A60 3.865,0.75 4.479,0.948 0.615,0.198 10 false 2 4.177,0.844 4.792,1.042 0.615,0.198 10 false L 3.052,0.75 3.667,0.948 0.615,0.198 10 false 13 3.396,0.844 4.01,1.042 0.615,0.198 10 false W 0.938,5 3.042,5.208 2.104,0.208 10 false : CAN Main Bus Line (CANH) 0.948,5.375 3.052,5.583 2.104,0.208 10 false : CAN Main Bus Line (CANL) 4.083,4.969 6.188,5.177 2.104,0.208 10 false : CAN Branch Line (CANH) 4.115,5.354 6.219,5.563 2.104,0.208 10 false : CAN Branch Line (CANL) 4.771,4.177 6.875,4.385 2.104,0.208 10 false X: Suspected Area 4.625,0.302 5.24,0.5 0.615,0.198 10 false F62 4.625,0.49 6.729,0.792 2.104,0.302 10 false No. 1 CAN Junction Connector 5.917,2.146 6.885,2.333 0.969,0.188 10 false A35*1 5.906,2.833 6.885,3.281 0.979,0.448 10 false Brake Actuator Assembly 5.958,1.302 6.573,1.5 0.615,0.198 10 false CANH 5.958,1.677 6.573,1.875 0.615,0.198 10 false CANL 5.708,1.302 6.323,1.5 0.615,0.198 10 false 25 5.698,1.646 6.313,1.844 0.615,0.198 10 false 14 5.24,1.198 5.854,1.396 0.615,0.198 10 false L 5.219,1.583 5.833,1.781 0.615,0.198 10 false W 4.49,1.24 5.104,1.438 0.615,0.198 10 false 5 4.448,1.615 5.063,1.813 0.615,0.198 10 false 16 3.729,1.135 4.344,1.333 0.615,0.198 10 false 6 2.906,1.135 3.521,1.333 0.615,0.198 10 false 17 2.885,2.156 3.5,2.354 0.615,0.198 10 false 16 3.719,2.156 4.333,2.354 0.615,0.198 10 false 5 3.844,2.594 4.458,2.792 0.615,0.198 10 false 23 3.083,2.604 3.698,2.802 0.615,0.198 10 false 22 4.146,2.813 4.76,3.01 0.615,0.198 10 false CANH 2.813,2.833 3.427,3.031 0.615,0.198 10 false CANL 3.51,3.396 4.125,3.594 0.615,0.198 10 false 120 Ω 2.771,3.656 3.385,3.854 0.615,0.198 10 false F38 2.76,3.813 4.792,4.167 2.031,0.354 10 false Combination Meter Assembly 0.917,1.604 3.021,1.906 2.104,0.302 10 false No. 23 CAN Junction Connector 0.323,4.198 2.75,4.406 2.427,0.208 10 false *1: for Manual Transaxle without VSC 2.833,4.188 4.938,4.396 2.104,0.208 10 false *2: for CVT without VSC 3.396,2.396 3.719,2.635 0.323,0.24 10 false W 4.135,2.406 4.458,2.646 0.323,0.24 10 false G 5.917,2.313 6.885,2.5 0.969,0.188 10 false A47*2 5.917,2.49 6.885,2.677 0.969,0.188 10 false A48*3 5.917,2.667 6.885,2.854 0.969,0.188 10 false A49*4 0.333,4.521 2.76,4.729 2.427,0.208 10 false *3: for Manual Transaxle with VSC 2.833,4.51 4.938,4.719 2.104,0.208 10 false *4: for CVT with VSC 0.167,0.156 1.083,0.354 0.917,0.198 10 false V Bus:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.74 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 23 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E221291C59
1.458,0.25 1.958,0.5 0.5,0.25 0.594,1.385 0.365,1.771 true 0.74,1.406 0.938,1.76 true 1.583,0.281 1.958,0.5 0.375,0.219 10 false F38 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 0.167,1.813 0.594,2.052 0.427,0.24 10 false CANL 0.854,1.792 1.292,2.031 0.438,0.24 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-23 (CANH) - F38-22 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

2.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
C343963C26
1.406,0.083 1.906,0.333 0.5,0.25 2.5,1.833 2.083,1.146 true 1.583,1.833 1.948,1.167 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 1.5,0.125 1.948,0.333 0.448,0.208 10 false F130 1.365,1.875 1.813,2.083 0.448,0.208 10 false CANH 2.344,1.875 2.792,2.083 0.448,0.208 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-13 (CANH) - F130-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (for 1NR-FE) A
OK (for 2NR-FE) B
NG C



A

B

C

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 23 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 23 CAN JUNCTION CONNECTOR)
a.

Reconnect the F130 ECM connector.


b.
E271709C08
1.51,0.167 2,0.469 0.49,0.302 1.5,2.354 1.99,2.656 0.49,0.302 1.615,1.302 1.177,0.646 true 1.615,1.583 1.292,1.958 true 2.115,4.052 1.771,3.646 true 1.25,4.073 1.635,3.667 true 1.781,3.406 2.281,2.729 true 1.083,2.729 1.615,3.365 true 1.646,0.24 2.104,0.438 0.458,0.198 10 false A60 1.573,2.427 2.031,2.625 0.458,0.198 10 false F174 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.844,0.458 1.417,0.688 0.573,0.229 10 false CANH*b 1.063,1.99 1.615,2.208 0.552,0.219 10 false CANL*b 0.781,2.552 1.354,2.75 0.573,0.198 10 false CANH*c 0.99,4.115 1.531,4.323 0.542,0.208 10 false CANL*c 2.125,2.531 2.656,2.75 0.531,0.219 10 false CANH*d 1.99,4.083 2.531,4.281 0.542,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 23 CAN Junction Connector)
*b to Brake Actuator Assembly
*c to Combination Meter Assembly
*d to No. 1 CAN Junction Connector


Disconnect the No. 23 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A60-5 (CANH) - A60-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly
F174-5 (CANH) - F174-16 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
F174-6 (CANH) - F174-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector main line) B
NG (ECU or sensor branch line) C
NG (Combination meter assembly main line) D



A

REPLACE NO. 23 CAN JUNCTION CONNECTOR

B

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 23 CAN JUNCTION CONNECTOR)

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F174 and A60 No. 23 CAN junction connectors.


b.
C353664C06
1.448,0.5 1.948,0.75 0.5,0.25 0.958,1.75 0.667,1.667 true 1.094,1.75 0.667,1.417 true 1.396,1.75 0.667,0.917 true 1.24,1.75 0.667,1.167 true 1,2.042 0.667,2.083 true 1.125,2.042 0.667,2.333 true 1.281,2.042 0.667,2.583 true 1.417,2.042 0.667,2.833 true 1.844,2.042 2.667,2.833 true 1.979,2.042 2.667,2.583 true 2.115,2.042 2.667,2.333 true 1.875,1.75 2.667,0.917 true 2.01,1.75 2.667,1.167 true 2.146,1.75 2.667,1.417 true 2.271,1.813 2.698,1.708 true 2.292,1.979 2.719,2 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 0.094,1.083 1,1.354 0.906,0.271 10 false CANH*d 0.104,1.333 1.01,1.604 0.906,0.271 10 false CANH*c 0.104,1.583 0.948,1.875 0.844,0.292 10 false CANH*b 0.094,0.833 1.063,1.104 0.969,0.271 10 false CANH*e 2.729,0.833 3.354,1.083 0.625,0.25 10 false CANH*f 2.729,1.083 3.396,1.333 0.667,0.25 10 false CANH*g 2.74,1.615 3.406,1.854 0.667,0.24 10 false CANH*i 0.115,2 0.958,2.292 0.844,0.292 10 false CANL*b 0.125,2.25 1.031,2.521 0.906,0.271 10 false CANL*c 0.115,2.5 1.021,2.771 0.906,0.271 10 false CANL*d 0.104,2.729 1.073,3 0.969,0.271 10 false CANL*e 2.729,2.75 3.354,3 0.625,0.25 10 false CANL*f 2.719,2.5 3.385,2.75 0.667,0.25 10 false CANL*g 2.729,2.25 3.396,2.49 0.667,0.24 10 false CANL*h 1.531,0.542 2.5,0.813 0.969,0.271 10 false F62 2.729,1.333 3.396,1.573 0.667,0.24 10 false CANH*h 2.75,1.927 3.417,2.167 0.667,0.24 10 false CANL*i
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to DLC3
*c to No. 23 CAN Junction Connector
*d to ECM
*e to Airbag ECU Assembly
*f to Certification ECU (Smart Key ECU Assembly)*1
*g to Air Conditioning Amplifier Assembly
*h to Steering sensor*2
*i to Power Steering ECU Assembly


Disconnect the No. 1 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F62-1 (CANH) - F62-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher DLC3
F62-2 (CANH) - F62-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 23 CAN junction connector
F62-3 (CANH) - F62-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
F62-4 (CANH) - F62-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag ECU assembly
F62-7 (CANH) - F62-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (Smart key ECU assembly)*1
F62-8 (CANH) - F62-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
F62-9 (CANH) - F62-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor*2
F62-10 (CANH) - F62-21 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly


*1: w/ Smart Entry and Start System

*2: w/ VSC



Result:
Result Proceed to
OK A
NG (No. 23 CAN junction connector main line) B
NG (ECU or sensor branch line) C
NG (DLC3 branch line) D
NG (ECM main line) E



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 23 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

C

5.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

E

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - NO. 1 CAN JUNCTION CONNECTOR)

5.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C152423C05
1.427,0.167 1.854,0.427 0.427,0.26 1.938,0.927 2.354,0.417 true 1.938,1.438 1.49,1.844 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *1 1.51,0.198 1.969,0.396 0.458,0.198 10 false F16 2.417,0.292 3.031,0.49 0.615,0.198 10 false CANH 1.094,1.792 1.708,1.99 0.615,0.198 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-6 (CANH) - F16-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR