Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2018.01
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the skid control ECU (brake actuator assembly).

WIRING DIAGRAM

E376660E01
5.427,3.146 5.885,3.344 0.458,0.198 10 false F38 5.417,3.323 6.635,3.802 1.219,0.479 10 false Combination Meter Assembly 5.583,4.521 6.042,4.719 0.458,0.198 10 false SPD 5.594,6.219 6.052,6.417 0.458,0.198 10 false SPD 1.427,6.24 1.885,6.438 0.458,0.198 10 false SPD 1.417,4.531 1.875,4.729 0.458,0.198 10 false SPD 1.417,2.667 1.875,2.865 0.458,0.198 10 false SPD 1.427,0.583 1.885,0.781 0.458,0.198 10 false SP1 4.25,2.542 4.708,2.74 0.458,0.198 10 false 17 2.958,6.135 3.417,6.333 0.458,0.198 10 false 20 2.948,2.552 3.406,2.75 0.458,0.198 10 false 15 4.26,6.135 4.719,6.333 0.458,0.198 10 false 13 4.25,4.438 4.708,4.635 0.458,0.198 10 false 18 0.615,1.094 2.24,1.615 1.625,0.521 10 false Skid Control ECU (Brake Actuator Assembly) 1.833,0.594 2.292,0.792 0.458,0.198 10 false A35 2.198,0.594 2.656,0.792 0.458,0.198 10 false A47 2.563,0.594 3.021,0.792 0.458,0.198 10 false A48 2.917,0.594 3.375,0.792 0.458,0.198 10 false A49 1.865,0.417 2.323,0.615 0.458,0.198 10 false 22 2.25,0.417 2.708,0.615 0.458,0.198 10 false 22 2.594,0.417 3.052,0.615 0.458,0.198 10 false 11 2.958,0.417 3.417,0.615 0.458,0.198 10 false 11 1.885,0.792 2.344,0.99 0.458,0.198 10 false *1 2.271,0.792 2.729,0.99 0.458,0.198 10 false *2 2.625,0.792 3.083,0.99 0.458,0.198 10 false *3 2.979,0.792 3.438,0.99 0.458,0.198 10 false *4 0.552,3.229 2.073,3.781 1.521,0.552 10 false Certification ECU (Smart Key ECU Assembly)*5 0.563,3.063 1.021,3.26 0.458,0.198 10 false F43 0.823,4.917 1.281,5.115 0.458,0.198 10 false F52 0.813,5.083 2.333,5.635 1.521,0.552 10 false Body Computer 1.823,6.135 2.281,6.333 0.458,0.198 10 false 17 0.531,6.646 0.99,6.844 0.458,0.198 10 false F142 0.531,6.813 2.531,7.219 2,0.406 10 false Radio Receiver Assembly*7 2.865,6.813 4.865,7.219 2,0.406 10 false No. 13 Junction Connector 2.865,6.646 3.323,6.844 0.458,0.198 10 false F162 5.302,6.135 5.76,6.333 0.458,0.198 10 false 23 5.375,4.448 5.833,4.646 0.458,0.198 10 false 2 5.823,6.656 6.281,6.854 0.458,0.198 10 false F130 5.823,6.823 6.281,7.021 0.458,0.198 10 false ECM 5.281,4.917 5.74,5.115 0.458,0.198 10 false F134 5.281,5.094 6.708,5.594 1.427,0.5 10 false Tire Pressure Warning ECU and Receiver*6 4.323,7.542 6.76,7.865 2.438,0.323 10 false *5: w/ Smart Entry and Start System 4.313,7.844 6.75,8.167 2.438,0.323 10 false *6: w/ Tire Pressure Warning System 4.313,8.135 6.75,8.458 2.438,0.323 10 false *7: w/ Radio Receiver 5.542,2.667 6,2.865 0.458,0.198 10 false +S 5.552,0.594 6.01,0.792 0.458,0.198 10 false SI 5.292,0.49 5.75,0.688 0.458,0.198 10 false 17 5.302,2.563 5.76,2.76 0.458,0.198 10 false 18 1.844,2.563 2.302,2.76 0.458,0.198 10 false 7 1.844,4.427 2.302,4.625 0.458,0.198 10 false 5 2.938,4.427 3.396,4.625 0.458,0.198 10 false 14 0.146,7.844 4.99,8.188 4.844,0.344 10 false *2: w/o VSC for LHD with Continuously Variable Transaxle 0.125,7.573 4.969,7.917 4.844,0.344 10 false *1: w/o VSC except LHD with Continuously Variable Transaxle 0.146,8.135 4.99,8.479 4.844,0.344 10 false *3: w/ VSC except LHD with Continuously Variable Transaxle 0.146,8.427 4.99,8.771 4.844,0.344 10 false *4: w/ VSC for LHD with Continuously Variable Transaxle

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (INPUT VOLTAGE)
a.
E219772C27
1.458,0.125 1.948,0.417 0.49,0.292 2.854,0.521 2.667,0.979 true 1.573,0.188 1.854,0.344 0.281,0.156 10 false F38 0.198,0.094 0.406,0.25 0.208,0.156 10 false *a 2.927,0.417 3.219,0.573 0.292,0.156 10 false +S
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F38-18 (+S) - Body ground Ignition switch ON 4.5 to 14 V


HINT:

If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.



Result:
Proceed to
OK
NG



OK

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 13 JUNCTION CONNECTOR)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
a.

Reconnect the F38 combination meter assembly connector.


b.

Disconnect the Skid Control ECU (Brake Actuator Assembly) connector.

C352274C01
4.99,0.292 5.5,0.542 0.51,0.25 1.667,0.292 2.177,0.542 0.51,0.25 1.667,2.5 2.177,2.75 0.51,0.25 4.99,2.5 5.5,2.75 0.51,0.25 2.625,2.156 2.24,1.406 true 5.854,2.156 5.479,1.406 true 5.594,3.385 6.51,3.74 true 2.344,3.385 3.281,3.74 true 0.75,0.26 1.167,0.542 0.417,0.281 12 false *A 4.021,0.26 4.417,0.542 0.396,0.281 12 false *B 0.75,2.469 1.156,2.719 0.406,0.25 12 false *C 4.01,2.469 4.385,2.76 0.375,0.292 12 false *D 0.188,0.156 0.5,0.313 0.313,0.156 10 false *a 1.802,0.323 2.292,0.573 0.49,0.25 10 false A35 1.792,2.542 2.281,2.792 0.49,0.25 10 false A48 5.115,0.333 5.604,0.583 0.49,0.25 10 false A47 5.125,2.542 5.615,2.792 0.49,0.25 10 false A49 2.688,2.083 3.177,2.333 0.49,0.25 10 false SP1 5.917,2.083 6.406,2.333 0.49,0.25 10 false SP1 6.583,3.667 7.073,3.917 0.49,0.25 10 false SP1 3.344,3.667 3.833,3.917 0.49,0.25 10 false SP1
*A w/o VSC except LHD with Continuously Variable Transaxle *B w/o VSC for LHD with Continuously Variable Transaxle
*C w/ VSC except LHD with Continuously Variable Transaxle *D w/ VSC for LHD with Continuously Variable Transaxle
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -



c.

Disconnect the Skid Control ECU (Brake Actuator Assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A35-22 (SP1) - Body ground*1 Ignition switch ON 11 to 14 V
A47-22 (SP1) - Body ground*2 Ignition switch ON 11 to 14 V
A48-11 (SP1) - Body ground*3 Ignition switch ON 11 to 14 V
A49-11 (SP1) - Body ground*4 Ignition switch ON 11 to 14 V


*1: w/o VSC except LHD with Continuously Variable Transaxle

*2: w/o VSC for LHD with Continuously Variable Transaxle

*3: w/ VSC except LHD with Continuously Variable Transaxle

*4: w/ VSC for LHD with Continuously Variable Transaxle



Result:
Proceed to
OK
NG



OK

3.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
3.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
a.
E270889C09
1.5,0.417 1.917,0.667 0.417,0.25 0.583,0.667 0.99,1.302 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 1.583,0.458 2.042,0.656 0.458,0.198 10 false F38 0.396,0.563 0.854,0.76 0.458,0.198 10 false SI 2.927,3.719 3.385,3.917 0.458,0.198 10 false GND 1.229,4 1.688,4.198 0.458,0.198 10 false (A)
*a Component with harness connected
(Combination Meter Assembly)


Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal F38-17 (SI) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn the wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Ignition switch ON, wheel being rotated

OK:

The waveform is displayed as shown in the illustration.


HINT:

As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-17 (SI) - A35-22 (SP1)*1 Always Below 1 Ω
F38-17 (SI) or A35-22 (SP1) - Body ground*1 Always 10 kΩ or higher
F38-17 (SI) - A47-22 (SP1)*2 Always Below 1 Ω
F38-17 (SI) or A47-22 (SP1) - Body ground*2 Always 10 kΩ or higher
F38-17 (SI) - A48-11 (SP1)*3 Always Below 1 Ω
F38-17 (SI) or A48-11 (SP1) - Body ground*3 Always 10 kΩ or higher
F38-17 (SI) - A49-11 (SP1)*4 Always Below 1 Ω
F38-17 (SI) or A49-11 (SP1) - Body ground*4 Always 10 kΩ or higher


*1: w/o VSC except LHD with Continuously Variable Transaxle

*2: w/o VSC for LHD with Continuously Variable Transaxle

*3: w/ VSC except LHD with Continuously Variable Transaxle

*4: w/ VSC for LHD with Continuously Variable Transaxle



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - NO. 13 JUNCTION CONNECTOR)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F162 No. 13 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-18 (+S) - F162-17 Always Below 1 Ω
F38-18 (+S) or F162-17 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT BODY COMPUTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT BODY COMPUTER
a.
E270875C34
1.5,0.167 2,0.417 0.5,0.25 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 1.604,0.198 2.063,0.396 0.458,0.198 10 false F162
*a Front view of wire harness connector
(to No. 13 Junction Connector)


Disconnect the F162 No. 13 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F162-14 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT ECM

NG

14.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - BODY COMPUTER)
7.INSPECT ECM
a.
E270875C34
1.5,0.167 2,0.417 0.5,0.25 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 1.604,0.198 2.063,0.396 0.458,0.198 10 false F162
*a Front view of wire harness connector
(to No. 13 Junction Connector)


Disconnect the F162 No. 13 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F162-13 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

8.SYSTEM CHECK

NG

15.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - ECM)
8.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ Smart Entry and Start System A
w/o Smart Entry and Start System B



A

9.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

10.SYSTEM CHECK
9.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
E270875C34
1.5,0.167 2,0.417 0.5,0.25 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 1.604,0.198 2.063,0.396 0.458,0.198 10 false F162
*a Front view of wire harness connector
(to No. 13 Junction Connector)


Disconnect the F162 No. 13 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F162-15 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

10.SYSTEM CHECK

NG

16.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
10.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ Tire Pressure Warning System A
w/o Tire Pressure Warning System B



A

11.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER

B

12.SYSTEM CHECK
11.INSPECT TIRE PRESSURE WARNING ECU AND RECEIVER
a.
E270875C34
1.5,0.167 2,0.417 0.5,0.25 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 1.604,0.198 2.063,0.396 0.458,0.198 10 false F162
*a Front view of wire harness connector
(to No. 13 Junction Connector)


Disconnect the F162 No. 13 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F162-18 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

12.SYSTEM CHECK

NG

17.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER)
12.SYSTEM CHECK
a.

Check the vehicle specifications.


Result:
Result Proceed to
w/ Radio Receiver A
w/o Radio Receiver B



A

13.INSPECT RADIO RECEIVER ASSEMBLY

B

REPLACE NO. 13 JUNCTION CONNECTOR

13.INSPECT RADIO RECEIVER ASSEMBLY
a.
E270875C34
1.5,0.167 2,0.417 0.5,0.25 0.094,0.063 0.406,0.219 0.313,0.156 10 false *a 1.604,0.198 2.063,0.396 0.458,0.198 10 false F162
*a Front view of wire harness connector
(to No. 13 Junction Connector)


Disconnect the No. 13 junction connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F162-20 - Body ground Ignition switch ON 4.5 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 13 JUNCTION CONNECTOR

NG

18.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - RADIO RECEIVER ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - BODY COMPUTER)
a.

Disconnect the F162 No. 13 junction connector.


b.

Disconnect the F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F162-14 - F52-5 (SPD) Always Below 1 Ω
F162-14 - F52-5 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - ECM)
a.

Disconnect the F162 No. 13 junction connector.


b.

Disconnect the F130 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F162-13 - F130-23 (SPD) Always Below 1 Ω
F162-13 or F130-23 (SPD) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for 1NR-FE) A
OK (for 2NR-FE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F162 No. 13 junction connector.


b.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F162-15 - F43-7 (SPD) Always Below 1 Ω
F162-15 or F43-7 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the F162 No. 13 junction connector.


b.

Disconnect the F134 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F162-18 - F134-2 (SPD) Always Below 1 Ω
F162-18 or F134-2 (SPD) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for Sedan) A
OK (for Hatchback) B
NG C



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (NO. 13 JUNCTION CONNECTOR - RADIO RECEIVER ASSEMBLY)
a.

Disconnect the F162 No. 13 junction connector.


b.

Disconnect the F142 radio receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F162-20 - F142-17 (SPD) Always Below 1 Ω
F162-20 or F142-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR