Home › Engine / Hybrid System › 1NR-FE ENGINE CONTROL › SFI SYSTEM › from 2018.01
RM30M0E _51 Engine / Hybrid System _053310 1NR-FE ENGINE CONTROL _0258661 SFI SYSTEM C

1NR-FE ENGINE CONTROL  SFI SYSTEM  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection duration and to provide an appropriate air fuel ratio. Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A213258E28
1.563,1.531 1.208,0.375 1.208,0.375 1.063,0.375 true 1.854,1.479 1.854,0.958 1.854,0.958 1.938,0.958 false 4.531,1.646 4.771,2.396 4.771,2.396 4.823,2.396 true 4.313,1.531 3.708,2.146 3.708,2.146 3.708,2.24 true 0.177,0.229 1.01,0.865 0.833,0.635 10 false Temperature Sensor (Thermistor) 1.833,0.635 3.135,0.885 1.302,0.25 10 false Power Transistor 1.99,0.906 4.021,1.146 2.031,0.24 10 false Platinum Hot Wire (Heater) 2.583,1.677 3.656,1.948 1.073,0.271 10 false Output Voltage 4.885,2.344 7.042,2.583 2.156,0.24 10 false Temperature Sensor (Thermistor) 2.635,2.292 4.802,2.458 2.167,0.167 10 false Platinum Hot Wire (Heater)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Mass Air Flow Circuit Low The mass air flow meter voltage is less than 0.2 V for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0103 Mass Air Flow Circuit High The mass air flow meter voltage is higher than 4.9 V for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the air flow rate by using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


271.0 or more
·

Open in E2G circuit




MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter circuit and stores the DTC.

Example:

When the sensor output voltage remains less than 0.2 V, or higher than 4.9 V for 3 seconds or more, the ECM stores the DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0102 or P0103.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A304668E25
1.354,2.354 2.99,2.719 1.635,0.365 10 false Driver Side Junction Block Assembly 3.917,2.573 5.271,2.771 1.354,0.198 10 false Mass Air Flow Meter 3.906,2.417 4.219,2.615 0.313,0.198 10 false B25 0.573,3.688 1.063,3.906 0.49,0.219 10 false Battery 0.385,2.552 0.802,2.75 0.417,0.198 10 false MAIN 0.958,1.333 1.656,1.542 0.698,0.208 10 false EFI-MAIN 2.448,1.333 3.156,1.531 0.708,0.198 10 false EFI NO. 2 1.906,2.01 2.188,2.198 0.281,0.188 10 false EFI 6.365,3.74 6.75,3.948 0.385,0.208 10 false ECM 5.885,1.885 6.198,2.073 0.313,0.188 10 false E2G 5.896,1.385 6.156,1.573 0.26,0.188 10 false VG 4.875,1.385 5.135,1.573 0.26,0.188 10 false VG 4.813,1.896 5.125,2.083 0.313,0.188 10 false E2G 3.969,1.083 4.198,1.26 0.229,0.177 10 false +B 3.25,0.969 3.385,1.177 0.135,0.208 10 false 3 0.698,0.969 0.813,1.177 0.115,0.208 10 false 1 2.865,2.125 2.979,2.333 0.115,0.208 10 false 9 0.906,2.125 1.021,2.333 0.115,0.208 10 false 8 3.125,2.125 3.344,2.313 0.219,0.188 10 false 6L 1.156,2.125 1.365,2.302 0.208,0.177 10 false 6J 3.208,1.177 3.49,1.365 0.281,0.188 10 false 6H 0.656,1.177 0.906,1.354 0.25,0.177 10 false 6B 5.479,3.271 5.854,3.458 0.375,0.188 10 false F130 5.51,2 5.813,2.167 0.302,0.167 10 false B47 5.51,1.5 5.833,1.698 0.323,0.198 10 false B47 5.552,1.281 5.75,1.458 0.198,0.177 10 false 24 5.552,1.792 5.75,1.969 0.198,0.177 10 false 32 5.563,3.063 5.76,3.24 0.198,0.177 10 false 6 3.802,1.083 3.969,1.313 0.167,0.229 10 false 3 5.198,1.385 5.313,1.583 0.115,0.198 10 false 5 5.198,1.896 5.313,2.094 0.115,0.198 10 false 4 5.885,3.271 6.344,3.469 0.458,0.198 10 false MREL 0.375,3.052 0.979,3.26 0.604,0.208 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0102 OR P0103)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.


Result:
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)

B

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - BODY GROUND)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)
A162182C22
0.25,1.292 0.646,1.542 0.396,0.25 1.74,1.396 2.063,0.604 true 0.323,1.333 0.635,1.49 0.313,0.156 10 false B25 0.229,0.167 0.396,0.333 0.167,0.167 10 false *a 2.083,0.521 2.521,0.708 0.438,0.188 10 false +B
*a Front view of wire harness connector
(to Mass Air Flow Meter)


a.

Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B25-3 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)

NG

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - MASS AIR FLOW METER)
3.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Disconnect the B47 ECM connector.


b.

Disconnect the B25 mass air flow meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B47-24 (VG) - B25-5 (VG) Always Below 1 Ω
B47-32 (E2G) - B25-4 (E2G) Always Below 1 Ω
B47-24 (VG) or B25-5 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the mass air flow meter.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 234 3

v.

Start the engine.


vi.

Check that the reading of the mass air flow meter changes when the engine is raced.

OK:

The reading changes.


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - MASS AIR FLOW METER)
a.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Disconnect the B25 mass air flow meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6H-3 - B25-3 (+B) Always Below 1 Ω
6H-3 or B25-3 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - BODY GROUND)
a.

Disconnect the B25 mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B25-4 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
7.CHECK HARNESS AND CONNECTOR (ECM - MASS AIR FLOW METER)
a.

Disconnect the B47 ECM connector.


b.

Disconnect the B25 mass air flow meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B47-32 (E2G) - B25-4 (E2G) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR