Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE(for 1NR-FE) › from 2018.01
RM30M0E _52 Drivetrain _017091 C54 MANUAL TRANSMISSION / TRANSAXLE _0267610 TRANSMISSION CONTROL CABLE(for 1NR-FE) A

C54 MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE(for 1NR-FE)  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Install the transmission control cable assembly to the body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
C294354C01
2.354,0.833 2.938,0.479 2.938,0.479 2.427,1.271 true 2.938,0.344 3.25,0.5 0.313,0.156 10 false *a 0.948,1.094 1.083,1.26 0.135,0.167 10 true A 2.24,0.385 2.375,0.552 0.135,0.167 10 true B 2.698,1.552 2.833,1.719 0.135,0.167 10 true B 1.021,2.083 1.156,2.25 0.135,0.167 10 true A
*a Paint Mark


Install the transmission control cable assembly to the No. 1 transmission control cable bracket with 2 new clips B.

NOTICE:

Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the No. 1 transmission control cable bracket before installing the clips.



c.

Connect the transmission control cable assembly to the manual transaxle assembly with the 2 washers and 2 clips A.


d.
C288539C01
2.24,0.906 2.552,0.708 false 1,1.875 1.313,1.677 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *1 2.594,0.604 2.906,0.76 0.313,0.156 10 false *2
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in


Rotate the 2 nuts of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.

NOTICE:

Do not rotate the nut excessively as it may damage the internal spring and transmission control cable assembly will not be reusable.



e.
C294353C01
2.375,0.375 2.625,0.604 false 2.177,3.583 2,3.708 false 2.719,2.76 2.927,3.396 true 0.563,0.385 0.813,0.615 false 1.271,3.75 1.042,3.51 false 2.188,3.5 2.5,3.656 0.313,0.156 10 false *1 2.875,3.427 3.188,3.583 0.313,0.156 10 false *2 2.208,0.292 2.521,0.448 0.313,0.156 10 false *3 0.406,0.302 0.719,0.458 0.313,0.156 10 false *a 0.271,0.573 0.583,0.729 0.313,0.156 10 false A 1.271,0.583 1.583,0.74 0.313,0.156 10 false A 0.854,3.427 1.167,3.583 0.313,0.156 10 false *a
*1 Clip A
*2 Clip B
*3 Lock
*a Protrusion


Install the transmission control cable assembly to the floor shift shift lever assembly.

NOTICE:
·

Install the transmission control cable assembly with the protrusion of the cable outer facing upwards.

·

After installation, make sure that the lock is projecting from A as shown in the illustration.




f.

Engage the clip B to connect the shift cable end of the transmission control cable assembly to the floor shift shift lever assembly.


g.

Connect the select cable end of the transmission control cable assembly to the floor shift shift lever assembly with the clip A.

NOTICE:
·

Install the transmission control cable assembly with the protrusion of the select cable end facing upwards.

·

Perform the installation with the clip A at the correct direction as shown in the illustration.




Hide 58151 2.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the body with the 2 bolts and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 4.INSTALL FRONT FLOOR CENTER BRACE

Hide 58810J 5.INSTALL CONSOLE BOX ASSEMBLY

Hide 58839A 6.INSTALL CONSOLE BOX HOLE COVER

Hide 58912C 8.INSTALL NO. 2 BOX SIDE PANEL

Hide 58911A 9.INSTALL NO. 1 BOX SIDE PANEL

Hide 58817A 10.INSTALL NO. 2 FRONT CONSOLE BOX INSERT

Hide 58910C 12.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 17801 17.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17880 19.INSTALL AIR CLEANER HOSE ASSEMBLY

Hide 12262 20.CONNECT NO. 2 VENTILATION HOSE

Hide 21.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing gas leaks in the exhaust system.

Click hereEngine / Hybrid System>1NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION