If the entry lock and unlock functions do not operate for the driver door only, the request code may not be being transmitted front door outside handle assembly (for driver door) may be malfunctioning. If the wireless door lock functions operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door)), or there may be wave interference.
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) or B27B0 is not output.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to the switch operation.
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK
Door locks operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the DTCs
DTC B27A1 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the front door outside handle assembly (for driver door) and perform an entry function check.
If the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the door handle, communication may not be possible.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
| Result | Proceed to |
|---|---|
| Entry function does not operate normally. | A |
| Entry function operates normally. | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry & Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D-Door Trigger Switch | Driver door trigger switch | ON or OFF | ON: Driver door trigger switch pressed
OFF: Driver door trigger switch not pressed |
·
Displays whether the trigger switch is on or off (even if the trigger switch is pressed and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is a trigger switch malfunction when the entry lock function does not operate. |
| Tester Display |
|---|
| D-Door Trigger Switch |
On the GTS screen, the display changes between ON and OFF as shown in the table above.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
Check the electrical key antenna (for driver door)
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
| Result | Proceed to |
|---|---|
| Wireless door lock buzzer does not sound | A |
| Wireless door lock buzzer sounds | B |
A
B
Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
for LHD:
Disconnect the H12 front door outside handle assembly LH connector.
for RHD:
Disconnect the G12 front door outside handle assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-9 (CLG5) - H12-3 (ANT1) | Always | Below 1 Ω |
| F44-25 (CG5B) - H12-6 (ANT2) | Always | Below 1 Ω |
| F43-10 (E) - Body ground | Always | Below 1 Ω |
| F44-9 (CLG5) or H12-3 (ANT1) - Body ground | Always | 10 kΩ or higher |
| F44-25 (CG5B) or H12-6 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-9 (CLG5) - G12-3 (ANT1) | Always | Below 1 Ω |
| F44-25 (CG5B) - G12-6 (ANT2) | Always | Below 1 Ω |
| F43-10 (E) - Body ground | Always | Below 1 Ω |
| F44-9 (CLG5) or G12-3 (ANT1) - Body ground | Always | 10 kΩ or higher |
| F44-25 (CG5B) or G12-6 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F43 and F44 certification ECU (smart key ECU assembly) connectors.
for LHD:
Connect the H12 front door outside handle assembly LH connector.
for RHD:
Connect the G12 front door outside handle assembly RH connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
Certification ECU (Smart Key ECU Assembly) |
*b | Waveform 1 |
| *c | Trigger switch ON | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F44-9 (CLG5) - F43-10 (E) | Procedure:
1.
Engine switch off 2.
All doors closed |
- | Not pulse generation |
| Procedure:
1.
Engine switch off 2.
All doors closed 3.
Press the trigger switch on the front door outside handle assembly (for driver door) |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the operation of the entry lock/unlock function.
Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly LH or RH before performing the inspection.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F43 certification ECU (smart key ECU assembly) connector.
for LHD:
Disconnect the H12 front door outside handle assembly LH connector.
for RHD:
Disconnect the G12 front door outside handle assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-4 (TSW1) - H12-1 (TRG+) | Always | Below 1 Ω |
| F43-10 (E) - Body ground | Always | Below 1 Ω |
| H12-4 (TRG-) - Body ground | Always | Below 1 Ω |
| F43-4 (TSW1) or H12-1 (TRG+) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-4 (TSW1) - G12-1 (TRG+) | Always | Below 1 Ω |
| F43-10 (E) - Body ground | Always | Below 1 Ω |
| G12-4 (TRG-) - Body ground | Always | Below 1 Ω |
| F43-4 (TSW1) or G12-1 (TRG+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door outside handle assembly (for driver door).
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>REMOVAL
Inspect the front door outside handle assembly (for driver door).
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY LOCK AND UNLOCK SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the operation of the entry lock/unlock function.
Disconnect and reconnect the connectors of certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) before performing the inspection.
Entry lock/unlock operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG