When a either door is opened and closed (the either door courtesy light switch turns on and off) with the ignition switch ON, or when the ignition switch is turned from off to ON, the rear seat belt warning light in the heater control and accessory assembly*1 or air conditioning control assembly*2 turns on to inform the driver of the rear seat belt condition. If a rear seat belt is fastened or unfastened, the warning light changes to indicate the current rear seat belt condition.
*1: for Manual Air Conditioning System
*2: for Automatic Air Conditioning System
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS ON.
Enter the following menus: Body Electrical / Combination Meter / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Driver Side Door | Driver side door courtesy light switch LH signal | OFF or ON | ON: Driver side door opened
OFF: Driver side door closed |
- |
| Passenger Side Door | Front passenger side door courtesy light switch LH signal | OFF or ON | ON: Front passenger side opened
OFF: Front passenger side closed |
- |
| Rear Left Side Door | Rear door courtesy light switch LH signal | OFF or ON | ON: Rear door LH opened
OFF: Rear door LH closed |
- |
| Rear Right Side Door | Rear door courtesy light switch RH signal | OFF or ON | ON: Rear door RH opened
OFF: Rear door RH closed |
- |
| Tester Display |
|---|
| Driver Side Door |
| Passenger Side Door |
| Rear Left Side Door |
| Rear Right Side Door |
The GTS display changes correctly in response to the rear door condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS ON.
Enter the following menus: Body Electrical / Combination Meter / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 2nd-Row Seatbelt Buckle (R) | Rear seat belt buckle switch RH | OFF or ON | OFF: Rear RH seat belt not fastened
ON: Rear RH seat belt fastened |
- |
| 2nd-Row Seatbelt Buckle (L) | Rear seat belt buckle switch LH | OFF or ON | OFF: Rear LH seat belt not fastened
ON: Rear LH seat belt fastened |
- |
| 2nd-Row Seatbelt Buckle (C) | Rear seat center belt buckle switch | OFF or ON | OFF: Rear seat center belt not fastened
ON: Rear seat center belt fastened |
- |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (R) |
| 2nd-Row Seatbelt Buckle (L) |
| 2nd-Row Seatbelt Buckle (C) |
The GTS display changes correctly in response to the rear seat belt condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS ON.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Rear Seat Belt | Rear seat belt warning light | OFF or ON | Confirm that the vehicle is stopped with the engine idling |
| Tester Display |
|---|
| Rear Seat Belt |
Value selected during Active Test is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check vehicle type.
| Result | Proceed to |
|---|---|
| for Automatic Air Conditioning System | A |
| for Manual Air Conditioning System | B |
A
B
Disconnect the F38 combination meter assembly connector.
Disconnect the F171 air conditioning control assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F171-7 (RLID) - F38-12 (RLMT) | Always | Below 1 Ω |
| F171-7 (RLID) or F38-12 (RLMT) - Body ground | Always | 10 kΩ or higher |
| F171-5 (RCID) - F38-11 (RCMT) | Always | Below 1 Ω |
| F171-5 (RCID) or F38-11 (RCMT) - Body ground | Always | 10 kΩ or higher |
| F171-4 (RRID) - F38-10 (RRMT) | Always | Below 1 Ω |
| F171-4 (RRID) or F38-10 (RRMT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to air conditioning control assembly) |
Disconnect the F171 air conditioning control assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F171-1 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F38 combination meter assembly connector.
Disconnect the F154 heater control and accesory assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F154-4 (RLID) - F38-12 (RLMT) | Always | Below 1 Ω |
| F154-4 (RLID) or F38-12 (RLMT) - Body ground | Always | 10 kΩ or higher |
| F154-3 (RCID) - F38-11 (RCMT) | Always | Below 1 Ω |
| F154-3 (RCID) or F38-11 (RCMT) - Body ground | Always | 10 kΩ or higher |
| F154-12 (RRID) - F38-10 (RRMT) | Always | Below 1 Ω |
| F154-12 (RRID) or F38-10 (RRMT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to heater control and accesory assembly) |
Disconnect the F154 heater control and accesory assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F154-8 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F38 combination meter assembly connector.
Disconnect the F181 rear seat inner with center belt assembly RH connector.
Disconnect the F182 rear seat inner with center belt assembly LH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F181-3 (CBR+) - F38-8 (RCSB) | Always | Below 1 Ω |
| F181-2 (CBR-) - Body ground | Always | Below 1 Ω |
| F181-3 (CBR+) or F38-8 (RCSB) - Body ground | Always | 10 kΩ or higher |
| F181-5 (RBR+) - F38-7 (RRBT) | Always | Below 1 Ω |
| F181-4 (RBR-) - Body ground | Always | Below 1 Ω |
| F181-5 (RBR+) or F38-7 (RRBT) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F182-1 (LBR+) - F38-9 (RLBT) | Always | Below 1 Ω |
| F182-2 (LBR-) - Body ground | Always | Below 1 Ω |
| F182-1 (LBR+) or F38-9 (RLBT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear seat inner with center belt assembly RH.
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for RH Side)>REMOVAL
Inspect the rear seat inner with center belt assembly RH.
Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for RH Side)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear seat inner with center belt assembly LH.
Inspect the rear seat inner with center belt assembly LH.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F38 combination meter assembly connector.
Disconnect the F31 front door courtesy light switch assembly LH connector.
Disconnect the F32 front door courtesy light switch assembly RH connector.
Disconnect the F33 rear door courtesy light switch assembly LH connector.
Disconnect the F34 rear door courtesy light switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F31-1 - F38-31 (PCTY) | Always | Below 1 Ω |
| F31-1 or F38-31 (PCTY) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F32-1 - F38-30 (DCTY) | Always | Below 1 Ω |
| F32-1 or F38-30 (DCTY) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F33-1 - F38-32 (RLCY) | Always | Below 1 Ω |
| F33-1 or F38-32 (RLCY) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F34-1 - F38-33 (RRCY) | Always | Below 1 Ω |
| F34-1 or F38-33 (RRCY) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front door courtesy light switch assembly.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL
Inspect the front door courtesy light switch assembly.
Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear door courtesy light switch assembly.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL
Inspect the rear door courtesy light switch assembly.
Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG