Home › Engine / Hybrid System › M15A-FKS (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087499 M15A-FKS ENGINE CONTROL _0418534 SFI SYSTEM C

M15A-FKS ENGINE CONTROL  SFI SYSTEM  P020113  Cylinder 1 Injector "A" Circuit Open  P020213  Cylinder 2 Injector "A" Circuit Open  P020313  Cylinder 3 Injector "A" Circuit Open  P062D13  Fuel Injector Driver Circuit Performance Bank 1 Circuit Open  


DESCRIPTION

The D-4 system has two fuel injection systems. One is an in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The ECM determines which fuel injection system to use in accordance with the engine conditions. The injection system uses an injector driver (EDU) built into the ECM to rapidly operate the fuel injector assemblies. It converts injection request signals from the ECM to high-voltage and high-current injector-drive signals that drive the fuel injector assemblies.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P020113 Cylinder 1 Injector "A" Circuit Open One of following conditions is met (1 trip detection logic):
·

Short to +B in fuel injector assembly (No. 1 cylinder) circuit for 20 times or more.

·

Open or short to ground in fuel injector assembly (No. 1 cylinder) circuit for 20 times or more.

·

Fuel injector assembly (No. 1 cylinder) circuit current reaches the high limit for 20 times or more.


·

Open or short in fuel injector assembly (No. 1 cylinder) circuit

·

Fuel injector assembly (No. 1 cylinder)

·

D INJ relay

·

ECM


Comes on DTC stored SAE: P0201
P020213 Cylinder 2 Injector "A" Circuit Open One of following conditions is met (1 trip detection logic):
·

Short to +B in fuel injector assembly (No. 2 cylinder) circuit for 20 times or more.

·

Open or short to ground in fuel injector assembly (No. 2 cylinder) circuit for 20 times or more.

·

Fuel injector assembly (No. 2 cylinder) circuit current reaches the high limit for 20 times or more.


·

Open or short in fuel injector assembly (No. 2 cylinder) circuit

·

Fuel injector assembly (No. 2 cylinder)

·

D INJ relay

·

ECM


Comes on DTC stored SAE: P0202
P020313 Cylinder 3 Injector "A" Circuit Open One of following conditions is met (1 trip detection logic):
·

Short to +B in fuel injector assembly (No. 3 cylinder) circuit for 20 times or more.

·

Open or short to ground in fuel injector assembly (No. 3 cylinder) circuit for 20 times or more.

·

Fuel injector assembly (No. 3 cylinder) circuit current reaches the high limit for 20 times or more.


·

Open or short in fuel injector assembly (No. 3 cylinder) circuit

·

Fuel injector assembly (No. 3 cylinder)

·

D INJ relay

·

ECM


Comes on DTC stored SAE: P0203
P062D13 Fuel Injector Driver Circuit Performance Bank 1 Circuit Open Open or short in fuel injector assembly (all cylinders) circuits for 30 times or more (1 trip detection logic).
·

Open or short in fuel injector assembly circuit

·

Fuel injector assembly

·

D INJ relay

·

ECM


Comes on DTC stored SAE: P062D

MONITOR DESCRIPTION

The fuel injection sequence occurs in numerical order from No. 1 to No. 3.

The ECM monitors the Injector Driver (EDU) at all times. If drivers or fuel injector assembly is malfunctioning, the EDU sends fuel injector assembly operation condition signals (fail signals) to the ECM. When the ECM receives the signals, the ECM stops the fuel injection control of the appropriate cylinders, cuts voltage to the appropriate D INJ relay, and illuminates the MIL.

MONITOR STRATEGY

Required Sensors/Components Fuel injector assembly
ECM (injector driver)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine [A].

7.

Idle the engine for 15 seconds or more [B].

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P020113, P020213, P020313 or P062D13.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A459255E01
2.563,1 2.875,1.198 0.313,0.198 10 false F1 2.521,1.156 5.24,1.406 2.719,0.25 10 false No. 1 Fuel Injector Assembly 2.594,0.688 2.906,0.885 0.313,0.198 10 false #1 3,0.688 3.313,0.885 0.313,0.198 10 false #10 2.604,1.677 2.917,1.875 0.313,0.198 10 false #2 2.594,2.688 2.906,2.885 0.313,0.198 10 false #3 2.99,1.677 3.302,1.875 0.313,0.198 10 false #20 2.99,2.677 3.302,2.875 0.313,0.198 10 false #30 2.583,1.99 2.896,2.188 0.313,0.198 10 false F2 2.563,2.99 2.875,3.188 0.313,0.198 10 false F3 2.417,0.698 2.729,0.896 0.313,0.198 10 false 2 2.427,1.677 2.74,1.875 0.313,0.198 10 false 2 2.427,2.677 2.74,2.875 0.313,0.198 10 false 2 3.292,2.677 3.604,2.875 0.313,0.198 10 false 1 3.281,1.677 3.594,1.875 0.313,0.198 10 false 1 3.281,0.688 3.594,0.885 0.313,0.198 10 false 1 5.938,0.365 6.25,0.563 0.313,0.198 10 false D51 5.927,0.771 6.24,0.969 0.313,0.198 10 false D51 5.927,1.365 6.24,1.563 0.313,0.198 10 false D51 5.927,1.771 6.24,1.969 0.313,0.198 10 false D51 5.927,2.365 6.24,2.563 0.313,0.198 10 false D51 5.927,2.76 6.24,2.958 0.313,0.198 10 false D51 5.958,0.208 6.271,0.406 0.313,0.198 10 false 16 5.958,0.615 6.271,0.813 0.313,0.198 10 false 17 5.958,1.198 6.271,1.396 0.313,0.198 10 false 11 5.958,1.604 6.271,1.802 0.313,0.198 10 false 10 5.969,2.208 6.281,2.406 0.313,0.198 10 false 13 5.969,2.604 6.281,2.802 0.313,0.198 10 false 14 6.292,0.375 6.75,0.573 0.458,0.198 10 false #1D+ 6.292,0.781 6.75,0.979 0.458,0.198 10 false #1D- 6.281,1.375 6.74,1.573 0.458,0.198 10 false #2D+ 6.292,2.771 6.75,2.969 0.458,0.198 10 false #3D- 6.292,1.771 6.75,1.969 0.458,0.198 10 false #2D- 6.281,2.375 6.74,2.573 0.458,0.198 10 false #3D+ 6.292,5.365 6.76,5.563 0.469,0.198 10 false E1D1 5.938,5.354 6.25,5.552 0.313,0.198 10 false A54 5.958,5.188 6.271,5.385 0.313,0.198 10 false 54 5.927,4.781 6.24,4.979 0.313,0.198 10 false A54 5.958,4.615 6.271,4.813 0.313,0.198 10 false 15 6.302,4.781 6.802,5.01 0.5,0.229 10 false MREL 4.417,4.5 4.917,4.729 0.5,0.229 10 false D INJ 0.802,3.802 1.302,4.031 0.5,0.229 10 false D INJ 4.167,3.563 4.479,3.76 0.313,0.198 10 false 3 4.938,3.563 5.25,3.76 0.313,0.198 10 false 5 6.281,3.646 6.781,3.875 0.5,0.229 10 false +BD1 5.958,3.479 6.271,3.677 0.313,0.198 10 false 53 5.927,3.646 6.24,3.844 0.313,0.198 10 false A54 6.281,4.24 6.781,4.469 0.5,0.229 10 false IREL 5.927,4.229 6.24,4.427 0.313,0.198 10 false A54 5.958,4.052 6.271,4.25 0.313,0.198 10 false 34 4.938,4.156 5.25,4.354 0.313,0.198 10 false 2 4.156,4.135 4.469,4.333 0.313,0.198 10 false 1 2.094,5.115 3.083,5.323 0.99,0.208 10 false EFI-MAIN NO.1 2.854,4.115 3.167,4.313 0.313,0.198 10 false 3 2.073,4.115 2.385,4.313 0.313,0.198 10 false 5 2.854,4.688 3.167,4.885 0.313,0.198 10 false 1 2.073,4.688 2.385,4.885 0.313,0.198 10 false 2 0.51,4.385 1.5,4.594 0.99,0.208 10 false EFI-MAIN NO.1 0.458,5.031 1.74,5.24 1.281,0.208 10 false BATT-MAIN NO.1 0.646,5.958 1.635,6.167 0.99,0.208 10 false Battery 6.49,5.948 6.917,6.208 0.427,0.26 10 false ECM 2.573,2.177 4.667,2.427 2.094,0.25 10 false No. 2 Fuel Injector Assembly 2.552,3.177 4.885,3.406 2.333,0.229 10 false No. 3 Fuel Injector Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

If the current from the D INJ relay is cut because DTC P062D13 is stored, DTC P123513 will be stored even if the fuel pump assembly (for high pressure side) is normal.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT (DTC P020113, P020213, P020313 AND/OR P062D13)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P020113, P020213, P020313 and P062D13 are output A
P062D13 is output B
P020113, P020213 or P020313 is output C




A

2.INSPECT D INJ RELAY

B

2.INSPECT D INJ RELAY

C

6.CHECK HARNESS AND CONNECTOR
2.INSPECT D INJ RELAY

OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF D INJ RELAY)

NG

REPLACE D INJ RELAY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF D INJ RELAY)
A459384C02
0.167,0.115 0.479,0.271 0.313,0.156 10 false *1 1.135,1.958 1.448,2.115 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 D INJ Relay


Pre-procedure1

a.

Remove the D INJ relay from the No. 1 engine room relay block and junction block assembly.


Procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (D INJ relay) - Body ground Always 11 to 14 V



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF D INJ RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - D INJ RELAY)

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF D INJ RELAY)
A459384C02
0.167,0.115 0.479,0.271 0.313,0.156 10 false *1 1.135,1.958 1.448,2.115 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block and Junction Block Assembly
*2 D INJ Relay


Pre-procedure1

a.

Remove the D INJ relay from the No. 1 engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (D INJ relay) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (D INJ RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY- D INJ RELAY)

5.CHECK HARNESS AND CONNECTOR (D INJ RELAY - ECM)

Pre-procedure1

a.

Remove the INJ relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (D INJ relay) - A54-53 (+BD1) Always Below 1 Ω
2 (D INJ relay) - A54-34 (IREL) Always Below 1 Ω
5 (D INJ relay) or A54-53 (+BD1) - Body ground and other terminals Always 10 kΩ or higher
2 (D INJ relay) or A54-34 (IREL) - Body ground and other terminals Always 10 kΩ or higher



Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR

Pre-procedure1

a.

Disconnect the ECM connector.


Procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D51-16 (#1D+) - D51-17 (#1D-) 20°C (68°F) 1.34 to 1.64 Ω
D51-11 (#2D+) - D51-10 (#2D-) 20°C (68°F) 1.34 to 1.64 Ω
D51-13 (#3D+) - D51-14 (#3D-) 20°C (68°F) 1.34 to 1.64 Ω
D51-16 (#1D+) or D51-17 (#1D-) - Body ground and other terminals Always 1 MΩ or higher
D51-11 (#2D+) or D51-10 (#2D-) - Body ground and other terminals Always 1 MΩ or higher
D51-13 (#3D+) or D51-14 (#3D-) - Body ground and other terminals Always 1 MΩ or higher


HINT:

The standard values shown are fuel injector assembly resistance values.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

NG

7.INSPECT FUEL INJECTOR ASSEMBLY (RESISTANCE)
7.INSPECT FUEL INJECTOR ASSEMBLY (RESISTANCE)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL INJECTOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION