Using the current from the TCM, the shift solenoid valve SLG controls the B1 brake when the shift lever is in R, and controls the S1 synchronizer when the shift lever is in P, N, D, M*1 or B*2.
When the TCM requests the shift mode to be changed to gear mode, the S1 synchronizer is engaged and input torque is transferred to the 1st gear.
When the TCM requests the shift mode to be changed to belt mode and certain conditions are met, the S1 synchronizer is released and input torque is not transferred to the 1st gear.
The shift stroke sensor detects the S1 synchronizer position using the magnet on the shift fork, and sends signals to the TCM.
*1: w/ Shift Paddle Switch
*2: w/o Shift Paddle Switch
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P08C37F | Pressure Control Solenoid "M" Actuator Stuck Off | Any of the following conditions are met (2-trip detection logic):
·
When the TCM commands the S1 synchronizer to be engaged, the shift stroke sensor output value is less than 9.205 mm (0.362 in.) for 4 seconds or more. ·
When the TCM commands the S1 synchronizer to be released, the shift stroke sensor output value is 9.205 mm (0.362 in.) or more for 3 seconds or more. ·
When the TCM commands the S1 synchronizer to be released, the shift stroke sensor output value is 1.498 mm (0.0590 in.) or more for 8 seconds or more. |
·
Transmission valve body assembly (Shift solenoid valve SLG) ·
Continuously variable transaxle assembly |
Comes on | DTC stored | SAE Code:
P08C4 |
| P091400 | Gear Shift Position Circuit Range/Performance | Any of the following conditions are met (2-trip detection logic):
·
When the TCM commands the S1 synchronizer to be engaged, the shift stroke sensor output value is less than 9.205 mm (0.362 in.) for 4 seconds or more. ·
When the TCM commands the S1 synchronizer to be released, the shift stroke sensor output value is 9.205 mm (0.362 in.) or more for 3 seconds or more. ·
When the TCM commands the S1 synchronizer to be released, the shift stroke sensor output value is 1.498 mm (0.0590 in.) or more for 8 seconds or more. |
·
Shift stroke sensor ·
Continuously variable transaxle assembly |
Comes on | DTC stored | SAE Code:
P0915 |
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnostic Condition | TCM commands the S1 synchronizer to be engaged | ○ | - | - |
| TCM commands the S1 synchronizer to be released | - | ○ | ○ | |
| Malfunction Condition | The shift stroke sensor output value is less than 9.205 mm (0.362 in.) | ○ | - | - |
| The shift stroke sensor output value is 9.205 mm (0.362 in.) or more | - | ○ | - | |
| The shift stroke sensor output value is 1.498 mm (0.0590 in.) or more | - | - | ○ | |
| Duration | 4 seconds or more | 3 seconds or more | 8 seconds or more | |
| Detection Logic | 2-trip detection logic | 2-trip detection logic | 2-trip detection logic | |
These DTCs are stored when any of the above detection patterns is met.
With the shift lever in P, N, D, M*1 or B*2, the shift solenoid valve SLG controls the S1 synchronizer and moves it to the requested position according to the requested shift mode.
When the TCM detects that the S1 synchronizer is not in the appropriate position, it determines that the shift solenoid valve SLG or shift stroke sensor is malfunctioning, illuminates the MIL and stores a DTC.
*1: w/ Shift Paddle Switch
*2: w/o Shift Paddle Switch
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Perform the D Position Test inspection in Road Test.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Stop the vehicle.
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
Input the DTC: P08C37F or P091400.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Refer to DTC P091412.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P091412
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>PRECAUTION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
If any DTCs other than P08C37F or P091400 are output, perform troubleshooting for those DTCs first.
Read the DTCs using the GTS.
If DTC P08C312 or P08C314 is output, perform troubleshooting for that DTC first.
If DTCs P08C312 and P08C314 are not output but DTC P091412 or P091414 is output, perform troubleshooting for DTC P091412 or P091414 first.
| Result | Proceed to |
|---|---|
| Only DTC P08C37F and/or P091400 is output | A |
| DTC P08C37F and/or P091400 and DTCs other than P08C312, P08C314, P091412 and P091414 are output | B |
| DTC P08C37F and/or P091400 and P08C312 are output | C |
| DTC P08C37F and/or P091400 and P08C314 are output | D |
| DTC P08C37F and/or P091400 and P091412 are output | E |
| DTC P08C37F and/or P091400 and P091414 are output | F |
A
B
C
D
E
F
Pre-procedure1
Connect 3 new dry-cell batteries (1.5 V each) in series.
Prepare a magnet or equivalent tool.
Remove the shift stroke sensor.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>SHIFT STROKE SENSOR>REMOVAL
Connect a positive (+) lead from the batteries to terminal 2 (VDD) and a negative (-) lead to terminal 3 (GND).
| *a | Component without harness connected
(Shift Stroke Sensor) |
*b | Magnet Movement Direction |
| *c | Dry Cell Battery | *d | Magnet |
| *e | 2.6 mm or less | - | - |
Procedure1
Wave the magnet left and right 2.6 mm (0.102 in.) or less from the tip of the shift stroke sensor to output a high/low signal while measuring the voltage.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D69-4 (VOUT) - D69-3 (GND) | High signal | 4.09 to 4.19 V |
| D69-4 (VOUT) - D69-3 (GND) | Low signal | 0.36 to 0.45 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D69-4 (VOUT) - D69-3 (GND) | High signal | 4.55 to 4.65 V |
| D69-4 (VOUT) - D69-3 (GND) | Low signal | 0.4 to 0.5 V |
Post-procedure1
Install the shift stroke sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Pre-procedure1
Disconnect the transmission wire connector from the shift solenoid valve SLG.
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL
| *1 | Transmission Valve Body Assembly | *2 | Shift Solenoid Valve SLG |
| *a | Component without harness connected
(Shift Solenoid Valve SLG) |
- | - |
Procedure1
Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the shift solenoid valve SLG connector. Check that the valve moves and makes an operating sound.
Valve moves and makes an operating sound.
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
When Not Using the Engine Support Bridge: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge)>REMOVAL
When Using the Engine Support Bridge: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>VALVE BODY ASSEMBLY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
for Registration: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>REGISTRATION
for Initialization: Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION