MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU detects that a safety device (interlock) is operated or that there is an open circuit in the detection circuit. (Even if an open circuit occurs while the vehicle is stopped, the system determines that the safety device was operated.)
The cause of this malfunction may be one of the following:
Service plug malfunction
Hybrid vehicle control ECU malfunction
Service plug malfunction
Wire harness malfunction
Connector malfunction
INSPECTION DESCRIPTION
| System Diagram Location | Inspection Content | Reason | Inspection Step |
|---|---|---|---|
| *a | ·
Check whether the safety device (interlock) is connected securely and installed properly (service plug grip, etc.). ·
Check the connection condition of the hybrid vehicle control ECU connector. |
DTC output due to improper connection or forgetting to install parts. | 4 to 6 |
| *b | Inspect the detection circuit. | DTC output due to an open circuit or improper connection (dirt, foreign matter, etc.). | 7 to 11 |
When the hybrid vehicle control ECU detects that a safety device (interlock) is operated, such as when the service plug grip or inverter cover is removed, it will prohibit hybrid system operation or shut off the system main relay. The 2 safety devices are located as follows; 1 in the service plug grip, 1 on the inverter cover for the terminals of the inverter with converter assembly motor cable and generator cable. If the service plug grip, inverter cover is removed, the interlock signal line will be open. If the vehicle is being driven, this condition will be determined to be an open circuit and the system main relays will not be shut off. When the safety devices are re-installed correctly, the system will return to normal when the ignition switch is turned to ON.
The system main relay will be turned off from the next trip after the open is detected until the condition returns to normal.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
| P0A0A13 | High Voltage System Interlock Circuit Open | Interlock signal line opens while the vehicle is being driven (at 5 km/h (3 mph) or more)
(1 trip detection logic) |
·
Wire harness or connector ·
Hybrid vehicle control ECU ·
Service plug grip |
Does not come on | Master Warning: Comes on |
| P0A0A92 | High Voltage System Interlock Performance or Incorrect Operation | Either of the following conditions is met:
·
With the vehicle stopped, the service plug grip with a safety device was removed. ·
With the vehicle stopped, the interlock signal line became open. (1 trip detection logic) |
·
Wire harness or connector ·
Hybrid vehicle control ECU ·
Service plug grip |
Does not come on | Master Warning: Comes on |
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for 2 minutes or more.
With ignition switch ON and wait for 5 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
Check the DTC judgment result.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
Inspecting the high-voltage system
Disconnecting the low voltage connector of the inverter with converter assembly
Disconnecting the low voltage connector of the HV battery
To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.
After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
| *a | Without waiting for 10 minutes |
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the auxiliary battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
As interlock circuit DTCs or other DTCs may be stored when the ignition switch to ON in the following procedure, make sure to clear the DTCs after inspection.
Pre-procedure1
None.
Procedure1
Check for DTCs.
| Result | Proceed to |
|---|---|
| P0A0A13 or P0A0A92 is output and DTCs other than the DTCs in the table below are output | A |
| P0A0A13 or P0A0A92 is output and any DTCs in the table below are output | B |
| Only P0A0A13 or P0A0A92 is output | C |
| Malfunction Content | Relevant DTC | |
|---|---|---|
| Microcomputer malfunction | P060647 | Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
| P060687 | Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message | |
| P060A47 | Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure | |
| P060A87 | Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message | |
| P060B49 | Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure | |
| P060B71 | Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck | |
| P060B1C | Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range | |
| P1CE349 | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure | |
| P1CE371 | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck | |
| P1CE31C | Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range | |
| P060A45 | Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure | |
| P060A44 | Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure | |
| P060A29 | Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid | |
| P060A49 | Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure | |
| Power source circuit malfunction | P06881F | ECM/PCM Power Relay Sense Circuit Intermittent |
| System malfunction | P1C9E9F | Hybrid/EV System Reset Stuck Off |
P0A0A13 or P0A0A92 may be output as a result of the malfunction indicated by the DTCs above.
The chart above is listed in inspection order of priority.
Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
Post-procedure1
Turn the ignition switch off.
A
B
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
C
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P06881F
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None.
Procedure1
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P0A0A13 or P0A0A92 is output | A |
| P0A0A13 or P0A0A92 is not output | B |
Post-procedure1
Turn the ignition switch off.
A
B
Be sure to wear insulated gloves.
| *1 | Service Plug Grip |
Check if the service plug grip is installed correctly.
Insert the service plug grip until a click sound is heard.
For the removal and installation procedures.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL
P0A0A92 is also set if the ignition switch is turned to ON with the service plug grip removed. Confirm the conditions when the malfunction occurred.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Procedure1
| *1 | Interlock Connector |
Check that the interlock connector at the service plug grip installation socket is connected correctly.
The connector is connected correctly.
Post-procedure1
Install the HV battery upper cover panel.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P056014
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the O72 service plug grip (interlock switch) connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the ignition switch to ON.
Procedure1
| *a | Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O72-1 (ILK) - Body ground | Ignition switch ON | 11 to 14 V |
Turning the ignition switch to ON with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Post-procedure1
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the O72 service plug grip (interlock switch) connector.
Install the HV battery upper cover panel.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Remove the service plug grip.
Procedure1
| *1 | Service Plug Grip |
Check the condition of the service plug grip interlock.
Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.
Post-procedure1
None.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Remove the HV battery upper cover panel.
Disconnect the O72 service plug grip (interlock switch) connector.
Procedure1
| *a | Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O72-2 (GND) - Body ground | Ignition switch off | Below 1 Ω |
Post-procedure1
Reconnect the O72 service plug grip (interlock switch) connector.
Install the HV battery upper cover panel.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the connections of each connector.
Dirt or foreign matter has not entered the connectors, and there is no evidence of contamination.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Pre-procedure1
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the H44 hybrid vehicle control ECU connector.
Remove the HV battery upper cover panel.
Disconnect the O72 service plug grip (interlock switch) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
*b | Rear view of wire harness connector
(to Service Plug Grip (Interlock Switch)) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H44-32 (ILK) - O72-1 (ILK) | Ignition switch off | Below 1 Ω |
Post-procedure1
Reconnect the O72 service plug grip (interlock switch) connector.
Install the HV battery upper cover panel.
Reconnect the H44 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG