Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID BATTERY SYSTEM
RM36W0E _51 Engine / Hybrid System _087936 HYBRID / BATTERY CONTROL _0420053 HYBRID BATTERY SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID BATTERY SYSTEM  P1A001C  Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range  P301A1C  Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range  


DESCRIPTION

The HV battery is composed of 48 cells (3.7 V each) in series. The battery ECU assembly monitors the voltage of each HV battery cell to detect malfunctions of the HV battery.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1A001C Hybrid Battery Stack 2 Cell Voltage Detection Voltage Out of Range An open is detected in the HV battery cell voltage detection circuits of the No. 2 HV supply stack sub-assembly.
(1 trip detection logic)
·

No. 2 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning:
Comes on
P301A1C Hybrid Battery Stack 1 Cell Voltage Detection Voltage Out of Range An open is detected in the HV battery cell voltage detection circuits of the No. 1 HV supply stack sub-assembly.
(1 trip detection logic)
·

No. 1 HV supply stack sub-assembly

·

Battery ECU assembly


Comes on Master Warning:
Comes on

Related Data List
DTC No. Data List
P1A001C Hybrid/EV Battery Cell 1 to 48 Voltage
P301A1C

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>UTILITY


1.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

2.

Turn the ignition switch off and wait for 2 minutes or more.

3.

Turn the ignition switch to ON and wait for 10 seconds or more.

4.

Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.

5.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

A459832E05
1.438,7.115 4.292,7.323 2.854,0.208 10 false No. 2 HV Supply Stack Sub-assembly 5.177,7.219 6.781,7.469 1.604,0.25 10 false Battery ECU Assembly 5.188,7.052 5.646,7.25 0.458,0.198 10 false z13 5.5,0.604 6.115,0.802 0.615,0.198 10 false VA48 5.5,0.979 6.115,1.177 0.615,0.198 10 false VA47 5.5,1.208 6.115,1.406 0.615,0.198 10 false VA46 5.5,1.448 6.115,1.646 0.615,0.198 10 false VA45 5.5,1.698 6.115,1.896 0.615,0.198 10 false VA44 5.5,1.927 6.115,2.125 0.615,0.198 10 false VA43 5.5,2.177 6.115,2.375 0.615,0.198 10 false VA42 5.5,2.396 6.115,2.594 0.615,0.198 10 false VA41 5.5,2.656 6.115,2.854 0.615,0.198 10 false VA40 5.5,2.896 6.115,3.094 0.615,0.198 10 false VA39 5.5,3.135 6.115,3.333 0.615,0.198 10 false VA38 5.5,3.365 6.115,3.563 0.615,0.198 10 false VA37 5.5,3.615 6.115,3.813 0.615,0.198 10 false VA36 5.5,3.865 6.115,4.063 0.615,0.198 10 false VA35 5.5,4.094 6.115,4.292 0.615,0.198 10 false VA34 5.5,4.333 6.115,4.531 0.615,0.198 10 false VA33 5.5,4.583 6.115,4.781 0.615,0.198 10 false VA32 5.5,4.823 6.115,5.021 0.615,0.198 10 false VA31 5.5,5.073 6.115,5.271 0.615,0.198 10 false VA30 5.5,5.333 6.115,5.531 0.615,0.198 10 false VA29 5.5,5.573 6.115,5.771 0.615,0.198 10 false VA28 5.5,5.833 6.115,6.031 0.615,0.198 10 false VA27 5.5,6.052 6.115,6.25 0.615,0.198 10 false VA26 5.5,6.292 6.115,6.49 0.615,0.198 10 false VA25 5.5,6.667 6.115,6.865 0.615,0.198 10 false GA1 5.177,0.51 5.427,0.677 0.25,0.167 10 false 36 5.188,0.875 5.438,1.042 0.25,0.167 10 false 24 5.188,1.115 5.438,1.281 0.25,0.167 10 false 12 5.198,1.354 5.448,1.521 0.25,0.167 10 false 35 5.198,1.604 5.448,1.771 0.25,0.167 10 false 23 5.198,1.833 5.448,2 0.25,0.167 10 false 11 5.188,2.083 5.438,2.25 0.25,0.167 10 false 34 5.188,2.313 5.438,2.479 0.25,0.167 10 false 22 5.188,2.563 5.438,2.729 0.25,0.167 10 false 10 5.177,2.802 5.427,2.969 0.25,0.167 10 false 33 5.177,3.031 5.427,3.198 0.25,0.167 10 false 21 5.25,3.26 5.5,3.427 0.25,0.167 10 false 9 5.167,3.521 5.417,3.688 0.25,0.167 10 false 32 5.167,3.771 5.417,3.938 0.25,0.167 10 false 20 5.229,4.01 5.479,4.177 0.25,0.167 10 false 8 5.156,4.24 5.406,4.406 0.25,0.167 10 false 31 5.156,4.5 5.406,4.667 0.25,0.167 10 false 19 5.219,4.719 5.469,4.885 0.25,0.167 10 false 7 5.135,4.99 5.385,5.156 0.25,0.167 10 false 30 5.146,5.24 5.396,5.406 0.25,0.167 10 false 18 5.208,5.479 5.458,5.646 0.25,0.167 10 false 6 5.146,5.74 5.396,5.906 0.25,0.167 10 false 29 5.146,5.969 5.396,6.135 0.25,0.167 10 false 17 5.208,6.198 5.458,6.365 0.25,0.167 10 false 5 5.156,6.583 5.406,6.75 0.25,0.167 10 false 28

A459832E04
1.365,7.115 3.99,7.333 2.625,0.219 10 false No. 1 HV Supply Stack Sub-assembly 5.198,7.24 6.802,7.49 1.604,0.25 10 false Battery ECU Assembly 5.208,7.021 5.667,7.219 0.458,0.198 10 false z15 5.5,0.604 6.115,0.802 0.615,0.198 10 false VA24 5.5,0.979 6.115,1.177 0.615,0.198 10 false VA23 5.5,1.208 6.115,1.406 0.615,0.198 10 false VA22 5.5,1.448 6.115,1.646 0.615,0.198 10 false VA21 5.5,1.698 6.115,1.896 0.615,0.198 10 false VA20 5.5,1.927 6.115,2.125 0.615,0.198 10 false VA19 5.5,2.177 6.115,2.375 0.615,0.198 10 false VA18 5.5,2.396 6.115,2.594 0.615,0.198 10 false VA17 5.5,2.656 6.115,2.854 0.615,0.198 10 false VA16 5.5,2.896 6.115,3.094 0.615,0.198 10 false VA15 5.5,3.135 6.115,3.333 0.615,0.198 10 false VA14 5.5,3.365 6.115,3.563 0.615,0.198 10 false VA13 5.5,3.615 6.115,3.813 0.615,0.198 10 false VA12 5.5,3.865 6.115,4.063 0.615,0.198 10 false VA11 5.5,4.094 6.115,4.292 0.615,0.198 10 false VA10 5.5,4.333 6.115,4.531 0.615,0.198 10 false VA9 5.5,4.583 6.115,4.781 0.615,0.198 10 false VA8 5.5,4.823 6.115,5.021 0.615,0.198 10 false VA7 5.5,5.073 6.115,5.271 0.615,0.198 10 false VA6 5.5,5.333 6.115,5.531 0.615,0.198 10 false VA5 5.5,5.573 6.115,5.771 0.615,0.198 10 false VA4 5.5,5.833 6.115,6.031 0.615,0.198 10 false VA3 5.5,6.052 6.115,6.25 0.615,0.198 10 false VA2 5.5,6.292 6.115,6.49 0.615,0.198 10 false VA1 5.5,6.667 6.115,6.865 0.615,0.198 10 false GA0 5.177,0.51 5.427,0.677 0.25,0.167 10 false 36 5.188,0.875 5.438,1.042 0.25,0.167 10 false 24 5.188,1.115 5.438,1.281 0.25,0.167 10 false 12 5.198,1.354 5.448,1.521 0.25,0.167 10 false 35 5.198,1.604 5.448,1.771 0.25,0.167 10 false 23 5.198,1.833 5.448,2 0.25,0.167 10 false 11 5.188,2.083 5.438,2.25 0.25,0.167 10 false 34 5.188,2.313 5.438,2.479 0.25,0.167 10 false 22 5.188,2.563 5.438,2.729 0.25,0.167 10 false 10 5.177,2.802 5.427,2.969 0.25,0.167 10 false 33 5.177,3.031 5.427,3.198 0.25,0.167 10 false 21 5.25,3.26 5.5,3.427 0.25,0.167 10 false 9 5.167,3.521 5.417,3.688 0.25,0.167 10 false 32 5.167,3.771 5.417,3.938 0.25,0.167 10 false 20 5.229,4.01 5.479,4.177 0.25,0.167 10 false 8 5.156,4.24 5.406,4.406 0.25,0.167 10 false 31 5.156,4.5 5.406,4.667 0.25,0.167 10 false 19 5.219,4.719 5.469,4.885 0.25,0.167 10 false 7 5.135,4.99 5.385,5.156 0.25,0.167 10 false 30 5.146,5.24 5.396,5.406 0.25,0.167 10 false 18 5.208,5.479 5.458,5.646 0.25,0.167 10 false 6 5.146,5.74 5.396,5.906 0.25,0.167 10 false 29 5.146,5.969 5.396,6.135 0.25,0.167 10 false 17 5.208,6.198 5.458,6.365 0.25,0.167 10 false 5 5.156,6.583 5.406,6.75 0.25,0.167 10 false 28

CAUTION / NOTICE / HINT

CAUTION:
·
A340358

Before the following operations are conducted, take precautions to prevent electric shock by turning the ignition switch off, wearing insulated gloves, and removing the service plug grip from HV battery.

-

Inspecting the high-voltage system

-

Disconnecting the low voltage connector of the inverter with converter assembly

-

Disconnecting the low voltage connector of the HV battery


·
A357588

To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

·
A358042

After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·
A357589C02
1.573,0.74 2.021,0.427 true 2.094,0.344 2.354,0.51 0.26,0.167 10 false *a
*a Without waiting for 10 minutes


After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

Make sure to insulate the high-voltage connectors and terminals of the HV battery with insulating tape after removing it.

If the HV battery stored without insulating the connectors and terminals, electric shock or fire may result.

·
A358021C02
0.531,4.146 0.844,4.344 0.313,0.198 10 false *a 2.74,4.146 3.052,4.344 0.313,0.198 10 false *b
*a Dealer
*b Battery Collection Agent


When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

-

Accidents such as electric shock may result if the HV battery is disposed of improperly or abandoned. Therefore, make sure to return all HV batteries through an authorized collection agent.


·

Before returning the HV battery, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>RECOVERY INSPECTION

·

Before returning the HV supply stack sub-assembly, make sure to perform a recovery inspection.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY STACK>RECOVERY INSPECTION

·

Make a note of the output DTCs as some of them may be necessary for recovery inspection of the HV battery and HV supply stack sub-assemblies.

·
A358020

After removing the HV battery, keep it away from water. Exposure to water may cause the HV battery to produce heat, resulting in a fire.



NOTICE:
·

After the ignition switch is turned off, there may be a waiting time before disconnecting the auxiliary negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

Pre-procedure1

a.

None.


Procedure1

b.

Check for DTCs.

Powertrain > HV Battery > Trouble Codes
50001 398
Powertrain > Hybrid Control > Trouble Codes
50001 397
Result:
Result Proceed to
Only P1A001C or P301A1C is output A
P1A001C or P301A1C is output and DTCs other than the DTCs in the table below are output B
P1A001C or P301A1C is output and hybrid battery system DTCs in the table below are output C
P1A001C or P301A1C is output and hybrid control system DTCs in the table below are output D


System Relevant DTC
Hybrid battery system P060A47 Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure
P060B49 Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure
P060687 Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message
Hybrid control system P0A1F94 Hybrid/EV Battery Energy Control Module Unexpected Operation


Post-procedure1

c.

Turn the ignition switch off.



A

2.CHECK DTC

B

2.CHECK DTC

C

D

2.CHECK DTC
a.

Check the DTCs that were output when the vehicle was brought to the workshop.


Result:
Result Proceed to
"P1A001C" is also output. A
"P301A1C" is also output. B



A

3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)

B

6.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
3.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

c.
A458603N01
1.667,0.135 2.021,0.385 0.354,0.25 1.698,0.167 1.99,0.365 0.292,0.198 10 true z13

Check the connections of the z13 battery ECU assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.



Post-procedure1

d.

Install the No. 1 HV battery hose.


Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Not connected securely The terminals are damaged or corroded C



A

4.CHECK FREEZE FRAME DATA

B

CONNECT SECURELY

C

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

4.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

b.

Read the value of freeze frame data items "Hybrid/EV Battery Cell 25 Voltage" through "Hybrid/EV Battery Cell 48 Voltage" for DTC P1A001C and make a note if the value of any is 1.6 V or less.

Powertrain > HV Battery > Trouble Codes
50001 398

Post-procedure1

c.

Turn the ignition switch off.

Result:
Proceed to
NEXT




NEXT

5.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 25 TO 48 VOLTAGE)
5.CHECK NO. 2 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 25 TO 48 VOLTAGE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

Result:
Result Proceed to
The voltage between the terminals is 1.6 V or less. A
Other than above B



A

REPLACE NO. 2 HV SUPPLY STACK SUB-ASSEMBLY

B

6.CHECK CONNECTOR CONNECTION CONDITION (BATTERY ECU ASSEMBLY CONNECTOR)
CAUTION:

Be sure to wear insulated gloves and protective goggles.


Pre-procedure1

a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the ignition switch to ON (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 HV battery hose.

HINT:

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>BATTERY ECU>REMOVAL



Procedure1

c.
A458602N01
2.385,0.083 2.74,0.323 0.354,0.24 2.417,0.104 2.719,0.302 0.302,0.198 10 true z15

Check the connections of the z15 battery ECU assembly connector.

HINT:

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


OK:

The connector is connected securely and there are no contact problems.


Result:
Result Proceed to
OK A
Not connected securely The terminals are not damaged or corroded B
Not connected securely The terminals are damaged or corroded C



Post-procedure1

d.

Install the No. 1 HV battery hose.



A

7.CHECK FREEZE FRAME DATA

B

CONNECT SECURELY

C

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

7.CHECK FREEZE FRAME DATA

Pre-procedure1

a.

None.


Procedure1

b.

Read the value of freeze frame data items "Hybrid/EV battery cell 1 voltage" through "Hybrid/EV battery cell 24 voltage" for DTC P301A1C and make a note if the value of any is 1.6 V or less.

Powertrain > HV Battery > Trouble Codes
50001 398

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

8.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 1 TO 24 VOLTAGE)
8.CHECK NO. 1 HV SUPPLY STACK SUB-ASSEMBLY (HYBRID BATTERY CELL 1 TO 24 VOLTAGE)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>P0E2D00

Result:
Result Proceed to
The voltage between the terminals is 1.6 V or less. A
Other than above B



A

REPLACE NO. 1 HV SUPPLY STACK SUB-ASSEMBLY

B