Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM J

M15A-FXE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU. Based on the signal sent from the ECM, the fuel pump control ECU adjusts the fuel pump operation speed.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.INSPECT FUEL PUMP CONTROL ECU
A459398C02
4.292,0.208 4.656,0.49 0.365,0.281 2.667,0.219 3.042,0.479 0.375,0.26 5,2.365 4.625,1.385 true 4.458,2.375 4.458,1.365 true 3.917,2.375 4.198,1.375 true 3.438,2.375 3.24,1.458 true 3.083,2.375 3.021,1.469 true 2.615,2.375 2.708,1.469 true 2.146,2.375 2.469,1.438 true 0.281,0.188 0.594,0.385 0.313,0.198 10 false *1 4.385,0.281 4.698,0.479 0.313,0.198 10 false O2 2.771,0.281 3.083,0.479 0.313,0.198 10 false O1 4.958,2.417 5.271,2.615 0.313,0.198 10 false +B 3.792,2.417 4.167,2.646 0.375,0.229 10 false GND 4.365,2.417 4.74,2.646 0.375,0.229 10 false FPC 3.354,2.417 3.729,2.646 0.375,0.229 10 false FPG 2.969,2.417 3.344,2.646 0.375,0.229 10 false FPU 2.5,2.417 2.875,2.646 0.375,0.229 10 false FPV 2.042,2.417 2.417,2.646 0.375,0.229 10 false FPW
*1 Fuel Pump Control ECU - -


a.

Disconnect the fuel pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-1 (+B) - O2-3 (GND) Always 10 Ω or higher
O2-1 (+B) - O2-2 (FPC) Always 2 kΩ or higher
O2-2 (FPC) - O2-3 (GND) Always 1 kΩ or higher
O1-1 (FPG) - O2-3 (GND) Always Below 1 kΩ
O1-2 (FPU) - O2-3 (GND) Always 2 kΩ or higher
O1-3 (FPV) - O2-3 (GND) Always 2 kΩ or higher
O1-4 (FPW) - O2-3 (GND) Always 2 kΩ or higher


HINT:

This procedure checks for an internal short of the fuel pump control ECU when its transistor is stuck on.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)

NG

REPLACE FUEL PUMP CONTROL ECU

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF FUEL PUMP CONTROL ECU)
a.

Disconnect the O2 fuel pump control ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
O2-1 (+B) - O2-3 (GND) Ignition switch ON 11 to 14 V


HINT:

Make a note of the measured voltage as it may be used in a following Active Test.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF EFI-MAIN NO. 2 RELAY)
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - ECM)
a.

Disconnect the O2 fuel pump control ECU connector.


b.

Disconnect the A53 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-2 (FPC) - A53-20 (FPC) Always Below 1 Ω
O2-2 (FPC) or A53-20 (FPC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.PERFORM ACTIVE TEST USING GTS (FUEL PUMP SINGLE PHASE ENERGIZATION)
A459399C01
2.708,0.281 3.094,0.531 0.385,0.25 2.031,2.323 2.479,1.479 true 2.677,2.302 2.708,1.49 true 3.135,2.344 2.99,1.5 true 0.177,0.104 0.49,0.302 0.313,0.198 10 false *1 2.781,0.313 3.24,0.51 0.458,0.198 10 false O1 1.802,2.365 2.25,2.656 0.448,0.292 10 false FPW 2.5,2.375 2.958,2.646 0.458,0.271 10 false FPV 3,2.396 3.479,2.646 0.479,0.25 10 false FPU
*1 Fuel Pump Control ECU - -


a.

Disconnect the fuel pump control ECU connector.


Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49
b.

Operate the fuel pump control ECU using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
O1-2 (FPU) - Body ground U Phase 4.4 to 8.4 V*
O1-3 (FPV) - Body ground V Phase 4.4 to 8.4 V*
O1-4 (FPW) - Body ground W Phase 4.4 to 8.4 V*


HINT:
·

*: This Active Test restricts the fuel pump control ECU output duty cycle to 50%. Therefore, the output voltage of the fuel pump control ECU will be approximately 50% of the power source voltage measured in a previous step.

·

Before performing this inspection, check that the auxiliary battery voltage is between 11 and 14 V (not depleted).




Result:
Result Proceed to
U phase, V phase and W phase are all normal A
U phase, V phase or W phase is abnormal B
U phase, V phase and W phase are all abnormal C



A

5.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP)

B

REPLACE FUEL PUMP CONTROL ECU

C

6.INSPECT ECM (FPC TERMINAL)
5.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - FUEL PUMP)
a.

Disconnect the O1 fuel pump control ECU connector.


b.

Disconnect the O21 fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O1-2 (FPU) - O21-3 (BLPU) Always Below 1 Ω
O1-3 (FPV) - O21-4 (BLPV) Always Below 1 Ω
O1-4 (FPW) - O21-2 (BLPW) Always Below 1 Ω
O1-2 (FPU) or O21-3 (BLPU) - Body ground and other terminals Always 10 kΩ or higher
O1-3 (FPV) or O21-4 (BLPV) - Body ground and other terminals Always 10 kΩ or higher
O1-4 (FPW) or O21-2 (BLPW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PUMP>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ECM (FPC TERMINAL)
a.

Disconnect the O2 fuel pump control ECU connector.


Powertrain > Engine > Active Test
Tester Display
Fuel Pump Single Phase Energization
50004 372 49
b.

Operate the fuel pump control ECU using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection GTS Operation Specified Condition
O2-2 (FPC) - Body ground Before Active Test → During Active Test Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU

NG

7.CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE OF EFI-MAIN NO. 2 RELAY)
A459242C01
0.188,0.792 0.5,0.948 0.313,0.156 10 false *1 1.177,0.167 1.49,0.323 0.313,0.156 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI-MAIN NO. 2 Relay


a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT EFI-MAIN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - EFI-MAIN NO. 2 RELAY)

8.INSPECT EFI-MAIN NO. 2 RELAY

OK

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - EFI-MAIN NO. 2 RELAY)
a.

Remove the EFI-MAIN NO. 1 relay and EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Remove the A/F HTR relay, VVT relay and EFI-MAIN NO. 3 relay from the No. 1 engine room relay block.

HINT:

Remove the A/F HTR relay, VVT relay and EFI-MAIN NO. 3 relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 1 relay) - 1 (EFI-MAIN NO. 2 relay) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay) or 1 (EFI-MAIN NO. 2 relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Disconnect the O2 fuel pump control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay) - O2-1 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 2 relay) or O2-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU - BODY GROUND)
a.

Disconnect the O2 fuel pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O2-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR