Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0421643 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door lock assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the power switch is turned to on (IG), the servo motor standard position is recognized. -


·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67673A 3.REMOVE REAR DOOR FRAME GARNISH

Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 67603 5.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68173B 6.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

Hide 68196B 7.REMOVE REAR DOOR BELT FRONT SEAL

Hide 68198 8.REMOVE REAR DOOR BELT REAR SEAL

Hide 67841E 9.REMOVE REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

Hide 67841E 10.REMOVE REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

Hide 68142C 11.REMOVE REAR DOOR GLASS RUN

Hide 67407E 12.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 68103 13.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 69330 14.REMOVE REAR DOOR LOCK ASSEMBLY

a.
B576094

Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the 3 screws and rear door lock assembly.


c.
B566007

Move the rear door lock assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock assembly.


d.

When reusing the rear door lock assembly:

i.
B576095

Remove the door lock wiring harness seal from the rear door lock assembly.



Hide 69730D 15.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B566009C02
3.073,1.115 2.563,1.115 true 3.083,1.031 3.396,1.229 0.313,0.198 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


b.
B576096

Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock assembly.


Hide 69770B 16.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B566011C02
1.281,1.823 1.594,0.969 true 1.208,1.844 1.521,2.042 0.313,0.198 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


b.
B576097

Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock assembly.