Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0421654 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Door window regulator sub-assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the power switch is turned to on (IG), the servo motor standard position is recognized. -


·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the RH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 67673A 3.REMOVE REAR DOOR FRAME GARNISH

a.
B564992

Disengage the claws and clip to remove the rear door frame garnish.


Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

a.
B576053

Disengage the claws and guides.


b.
B567652

Disconnect the connector to remove the rear power window regulator switch assembly with rear door armrest base upper panel.


Hide 67603 5.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B564994C01
1.958,1.083 2.302,0.594 true 2.354,0.49 2.583,0.698 0.229,0.208 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, open the rear door inside handle bezel plug.


b.
B564995

Remove the 3 screws.


c.
B576054C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the clips as shown in the illustration.


d.
B576055C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the rear door trim board sub-assemblywith the rear door glass inner weatherstrip and rear door belt seal as shown in the illustration.


e.
B564997C01
1.219,1.583 1.469,1.333 true 1.219,0.813 1.469,1.063 true 0.99,0.729 1.156,0.875 0.167,0.146 10 true *1 1.031,1.583 1.198,1.729 0.167,0.146 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Disengage the guides to disconnect the rear door inside locking cable assembly and rear door lock remote control cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.


Hide 69205A 6.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B564998

Disengage the guides to remove the rear door inside handle sub-assembly.


Hide 69283A 7.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B567833

Disengage the claw to remove the rear door inside handle bezel plug.


Hide 68173B 8.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

a.
B576056C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door glass inner weatherstrip with the rear door belt seal.


Hide 68196B 9.REMOVE REAR DOOR BELT FRONT SEAL

a.
B576057

Remove the rear door belt front seal from the rear door glass inner weatherstrip.


Hide 68198 10.REMOVE REAR DOOR BELT REAR SEAL

a.
B576058

Disengage the claws to remove the rear door belt rear seal.


Hide 86160B 11.REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

Hide 67841E 12.REMOVE REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

a.
B565003

Remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 67841E 13.REMOVE REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

a.
B565004

Remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 68142C 14.REMOVE REAR DOOR GLASS RUN

a.
B565009

Remove the rear door glass run.


Hide 67407E 15.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B565005

Remove the 2 bolts, nut and rear door window division bar sub-assembly.


Hide 68103 16.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

a.

Connect the rear power window regulator switch assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Move the rear door glass sub-assembly so that the door glass bolts can be seen.


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


e.

Connect the rear power window regulator switch assembly.


f.
B576059

Remove the 2 bolts.


g.
B576060C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the rear door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the front door glass subassembly.



Hide 17.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

a.
B565008

Disengage the clamp to separate the wire harness.


b.

Disconnect the connector.


c.

Remove the 6 nuts and rear door window regulator assembly.


Hide 69330 18.REMOVE REAR DOOR LOCK ASSEMBLY

Hide 69230 19.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B565010

Disengage the claws and move the lever as shown in the illustration.


b.
B565011C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door outside handle assembly as shown in the illustration.


Hide 69227J 20.REMOVE REAR DOOR OUTSIDE HANDLE COVER

a.
B565012

Using a T30 "TORX" socket wrench, loosen the screw.


b.

Disengage the claws to remove the rear door outside handle cover.


Hide 69241G 21.REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD

a.
B565013

Disengage the claws and guide to remove the rear door outside handle front pad.


Hide 69242G 22.REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD

a.
B565014

Disengage the guides to remove the rear door outside handle rear pad.


Hide 69203A 23.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B565015

Using a T30 "TORX" socket wrench, loosen the screw.


b.
B565016C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guides to remove the rear door outside handle frame sub-assembly as shown in the illustration.


Hide 75707 24.REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR WINDOW FRAME MOULDING>REMOVAL


Hide 68180C 25.REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR DOOR BELT MOULDING>REMOVAL


Hide 75923 26.REMOVE NO. 2 BLACK OUT TAPE

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Rear Door)>REMOVAL


Hide 68630D 27.REMOVE REAR DOOR CHECK ASSEMBLY

a.
B565017

Remove the 3 bolts and rear door check assembly.


Hide 67871 28.REMOVE REAR DOOR WEATHERSTRIP

a.
B565018C01
0.385,0.75 0.802,0.333 true 0.25,0.719 0.563,0.917 0.313,0.198 10 false *a
*a Clip A


Disengage the clip A and other clips to remove the rear door weatherstrip.


Hide 67837C 29.REMOVE REAR DOOR DUST PROOF SEAL

a.

for Type A:

i.
B565019

Disengage the claws to remove the 3 rear door dust proof seals.

NOTICE:

When installing, install 2 dust proof seals in the same way as for type B.




b.

for Type B:

i.
B621542

Disengage the claws to remove the 2 rear door dust proof seals.