The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front door removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
Use the same procedure for the LH side and RH side.
The following procedure is for the RH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2. CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>REMOVAL
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
67491A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Disengage the claws and clip to remove the front door lower frame bracket garnish.
74232
4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)
Disengage the claws and guides.
Disconnect the 2 connectors to remove the multiplex network master switch assembly with front armrest base upper panel.
74231
5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)
Disengage the claws and guides.
Disconnect the connector to remove the power window regulator switch assembly with front armrest base upper panel.
67655
6.REMOVE FRONT DOOR TRIM GARNISH
|
Remove in this Direction |
Remove the screw.
Disengage the claws to remove the front door trim garnish as shown in the illustration.
67601
7.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
| *a | Protective Tape |
Using a screwdriver with its tip wrapped in protective tape, disengage the claw to open the front door inside handle bezel plug.
Remove the 3 screws.
|
Place Hands Here |
|
Remove in this Direction |
Disengage the clips as shown in the illustration.
|
Remove in this Direction |
Disengage the front door trim board sub-assembly with the front door glass inner weatherstrip, front door vent seal and front door panel protector as shown in the illustration.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
|
Remove in this Direction |
Disengage the guides to disconnect the front door inside locking cable assembly and front door lock remote control cable assembly to remove the front door trim board sub-assembly as shown in the illustration.
69205
8.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Disengage the guides to remove the front door inside handle sub-assembly.
69283
9.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Disengage the claw to remove front door inside handle bezel plug.
68171B
10.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP
|
Remove in this Direction |
Disengage the claws to remove the front door glass inner weatherstrip with the front vent seal and front door panel protector as shown in the illustration.
67837A
11.REMOVE FRONT DOOR VENT SEAL
Remove the front door vent seal from the front door glass inner weatherstrip.
67855B
12.REMOVE FRONT DOOR PANEL PROTECTOR
Remove the front door panel protector from the front door glass inner weatherstrip.
86160
13.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
87910
14.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
67831
15.REMOVE FRONT DOOR SERVICE HOLE COVER
Turn the 3 front door service hole cover clips 45° to remove it clips as shown in the illustration.
Disengage the guide and clamp to separate the wire harness from the front door service hole cover.
Disengage the clips to remove the front door service hole cover.
8983A
16.REMOVE SIDE AIRBAG PRESSURE SENSOR
68101
17.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Remove the hole plug.
for Driver Side:
Connect the multiplex network master switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the multiplex network master switch assembly.
for Front Passenger Side:
Connect the power window regulator switch assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the power window regulator switch assembly.
Remove the 2 bolts.
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Remove the front door glass sub-assembly as shown in the illustration.
Do not damage the front door glass sub-assembly.
18.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
Disconnect the connector.
Remove the 6 nuts and front door window regulator assembly.
68141C
19.REMOVE FRONT DOOR GLASS RUN
Remove the front door glass run.
67403F
20.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Remove the bolt.
Disengage the guide to remove the front door rear lower frame sub-assembly as shown in the illustration.
67401F
21.REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Remove the 2 bolts and front door front lower frame sub-assembly.
69210
22.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY
w/ Entry and Start System:
| *a | Protective Tape |
Disengage the claws.
Using a screwdriver with its tip wrapped in protective tape, disconnect the connector.
Disengage the 2 claws and move the lever as shown in the illustration.
|
Remove in this Direction |
Remove the front door outside handle assembly as shown in the illustration.
69510
23.REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Remove the front door lock cylinder assembly.
69217F
24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the claws and guides to remove the front door outside handle cover.
69241H
25.REMOVE FRONT DOOR OUTSIDE HANDLE FRONT PAD
Disengage the claws and guide to remove the front door front outside handle pad.
69242E
26.REMOVE FRONT DOOR OUTSIDE HANDLE REAR PAD
Disengage the guides to remove the front door outside handle rear pad.
69310
27.REMOVE FRONT DOOR LOCK ASSEMBLY
69201A
28.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
w/ Entry and Start System:
Disengage the clamp to separate the wire harness.
|
Remove in this Direction |
Using a T30 "TORX" socket wrench, loosen the screw.
Disengage the guides to remove the front door outside handle frame sub-assembly as shown in the illustration.
69311A
29.REMOVE FRONT DOOR LOCK OPEN ROD
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Disengage the snap to remove the front door lock open rod from the front door outside frame sub-assembly as shown in the illustration.
68160C
30.REMOVE FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>REMOVAL
68610B
31.REMOVE FRONT DOOR CHECK ASSEMBLY
Remove the 3 bolts and front door check assembly.
67861
32.REMOVE FRONT DOOR WEATHERSTRIP
| *a | Clip A |
Disengage the clip A and other clips to remove the front door weatherstrip.
33.REMOVE CUSHION
Disengage the claws to remove the 2 cushions.
75921C
34.REMOVE NO. 1 BLACK OUT TAPE
Use the same procedure as for the LH side.
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Front Door)>REMOVAL
67837B
35.REMOVE FRONT DOOR DUST PROOF SEAL
for Type A:
Disengage the claws to remove the 3 front door dust proof seals.
When installing, install 2 dust proof seals in the same way as for type B.
for Type B:
Disengage the claws to remove the 2 front door dust proof seals.