Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0421652 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the RH side.



PROCEDURE

Hide 67837B 1.INSTALL FRONT DOOR DUST PROOF SEAL

B621541

a.

Engage the claws to install 2 new front door dust proof seals.

NOTICE:

Even if there were 3 dust proof seals at the time of removal, install 2 dust proof seals as shown in the illustration.



Hide 75921C 3.INSTALL NO. 1 BLACK OUT TAPE

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE (for Front Door)>INSTALLATION


Hide 4.INSTALL CUSHION

B563128

a.

Engage the claws to install 2 new cushions.


Hide 67861 5.INSTALL FRONT DOOR WEATHERSTRIP

a.
B563127C01
2.948,0.479 3.198,0.188 true 3.198,0.052 3.375,0.25 0.177,0.198 10 false *a
*a Clip A


Engage the clip A and other clips to install the front door weatherstrip.


Hide 68610B 6.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Clean the bolt hole in the vehicle body.


b.

Clean the threads of the bolt A.


c.

Apply adhesive to the threads of the bolt A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
B563126C01
0.969,1.448 1.135,1.615 0.167,0.167 10 true *a 1.656,1.448 1.823,1.615 0.167,0.167 10 true *b 1.667,0.698 1.833,0.865 0.167,0.167 10 true *b
*a Bolt A
*b Bolt B


Install the front door check assembly with the bolt A and 2 bolts B.

Torque:
Bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt B : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 68160C 7.INSTALL FRONT DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>INSTALLATION


Hide 69311A 8.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B563130C02
1.083,2.354 0.677,1.99 true 0.5,1.885 0.813,2.083 0.313,0.198 10 false *a
*a Snap
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the snap to install the front door lock open rod to the front door outside frame sub-assembly as shown in the illustration.


Hide 69201A 9.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B563131C02
0,0 0,0 false
V113147

Install in this Direction


Engage the guides to install the front door outside handle frame sub-assembly as shown in the illustration.


c.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

w/ Entry and Start System:

i.
B576045

Engage the clamp to install the wire harness.



Hide 69310 10.INSTALL FRONT DOOR LOCK ASSEMBLY

Hide 69242E 11.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B563122

Engage the guides to install the front door outside handle rear pad.


Hide 69241H 12.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B563121

Engage the guide and claws to install the front door outside handle front pad.


Hide 69510 13.INSTALL FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

a.

Install the front door lock cylinder assembly.

HINT:

Check that the front door lock cylinder assembly is inserted into the front door lock with motor assembly.



b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B563117

Install the hole plug.


Hide 69217F 14.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B563120

Engage the claws and guides to install the front door outside handle cover.


b.

Using a T30 "TORX" socket wrench, tighten the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B563119

Install the hole plug.


Hide 69210 15.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B563132C01
0,0 0,0 false
V113147

Install in this Direction


Install the front door outside handle assembly as shown in the illustration.


b.
B563133

Move the lever and engage the claws as shown in the illustration.


c.

w/ Entry andStart System:

i.
B563134

Connect the connector.


ii.

Engage the claws.



Hide 67401F 16.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B563112C01
0.563,0.656 1.24,0.656 true 0.469,1.708 1.052,1.708 true 0.375,0.583 0.688,0.781 0.313,0.198 10 false *a 0.313,1.615 0.625,1.813 0.313,0.198 10 false *b
*a Bolt A
*b Bolt B


Install the front door front lower frame sub-assembly with the bolt A and bolt B.

Torque:
Bolt A : 6.0 N*m (61 kgf*cm, 53 in.*lbf)
Bolt B : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 67403F 17.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B566052C02
0,0 0,0 false
V113147

Install in this Direction


Engage the guide to install the front door rear lower frame sub-assembly as shown in the illustration.


b.

Install the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 68141C 18.INSTALL FRONT DOOR GLASS RUN

a.
B563110

Install the front door glass run.


Hide 19.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.

Install the front door window regulator assembly with the 6 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


c.

Connect the connector.


Hide 68101 20.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

for Driver Side:

i.

Connect the multiplex network master switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the multiplex network master switch assembly.



b.

for Front Passenger Side:

i.

Connect the power window regulator switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the front door glass sub-assembly so that the door glass bolt holes can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the power window regulator switch assembly.



c.
B563135C02
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.

NOTICE:

Be careful not to damage the front door glass sub-assembly.



d.

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
B563106

Install the hole plug.


Hide 67831 22.INSTALL FRONT DOOR SERVICE HOLE COVER

a.
B576047

Pass the front door lock remote control cable assembly, front door inside locking cable assembly and wire harness through front door service hole cover.


b.

Engage the clips to install the front door service hole cover.


c.
B576048

Engage the clamp and guide.


d.

Insert the 3 front door service hole cover clips and turn them 45° as shown in the illustration.


Hide 87910 23.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSTALLATION


Hide 86160 24.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 67855B 25.INSTALL FRONT DOOR PANEL PROTECTOR

a.
B576042

Install the front door panel protector to the front door glass inner weatherstrip.


Hide 67837A 26.INSTALL FRONT DOOR VENT SEAL

a.
B576041

Install the front door vent seal to the front door glass inner weatherstrip.


Hide 68171B 27.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B576049

Install the front door glass inner weatherstrip with the front door panel protector and front door vent seal.


Hide 69283 28.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG

a.
B567833

Engage the claw to install the front door inside handle bezel plug.


Hide 69205 29.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B563099

Engage the guides to install the front door inside handle sub-assembly.


Hide 67601 30.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B563142C01
0.74,1.583 0.958,1.333 true 0.698,0.844 0.948,1.094 true 0.583,0.708 0.75,0.875 0.167,0.167 10 true *1 0.615,1.573 0.781,1.74 0.167,0.167 10 true *2
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


Engage the guides to connect the front door lock remote control cable assembly and front door inside locking cable assembly.


b.
B567839

Engage the claws and clips to install the front door trim board sub-assembly as shown in the illustration.


c.

Install the 3 screws.


d.
B564984

Engage the claw to close the front door inside handle bezel plug.


Hide 67655 31.INSTALL FRONT DOOR TRIM GARNISH

a.
B563141C02
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the front door trim garnish as shown in the illustration.


b.

Install the screw.


Hide 74232 32.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

a.

Connect the 2 connectors.


b.
B576034

Engage the claws and guides to install the multiplex network master switch assembly with front door upper armrest base panel.


Hide 74231 33.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B576035

Engage the claws and guides to install the power window regulator switch assembly with front door upper armrest base panel.


Hide 67491A 34.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH

B563088

a.

Engage the claws and clip to install the front door lower frame bracket garnish.


Hide 35.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 36. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 38.INITIALIZE POWER WINDOW CONTROL SYSTEM