Home › Drivetrain › K320 (MULTIDRIVE / CVT) › TRANSMISSION CONTROL CABLE › 2020.03–2020.07
RM36W0E _52 Drivetrain _087836 K320 MULTIDRIVE / CVT _0422065 TRANSMISSION CONTROL CABLE A

K320 MULTIDRIVE / CVT  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
If possible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)
If impossible, read the transaxle compensation code from the previous ECM:
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Update ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 5.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 7.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 51447D 8.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58151 10.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
C434360

Remove nut and front No. 1 floor heat insulator from the vehicle body.


Hide 58153 11.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

a.
C429238

Remove 4 nuts and front No. 2 floor heat insulator from the vehicle body.


Hide 58910C 12.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 33820B 13.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Move the shift lever to N.


b.
C429505

Disconnect the transmission control cable assembly from the transmission floor shift assembly.


c.
C432467C02
2.354,2.75 2.771,3.042 true 1.792,2.51 2.104,2.708 0.313,0.198 10 false *a 2.813,3 3.125,3.198 0.313,0.198 10 false *1
*1 Lock Nut
*a Counterclockwise


Rotate the lock nut counterclockwise approximately 180° and, while holding the lock nut in that position, disconnect the transmission control cable assembly from the transmission floor shift assembly.


d.
C429227C03
1.698,2.521 2.031,2.146 false 2.063,2.073 2.375,2.229 0.313,0.156 10 false *1 2.969,3.323 3.281,3.479 0.313,0.156 10 false *a
*1 Clip
*a 45° to 60°


While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


e.
C429228

Remove the clip to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.


f.
C434355

Remove the nut.


g.

Disengage the guide to disconnect the transmission control cable assembly from the vehicle body.


h.
C434356

Remove the 2 nuts and transmission control cable assembly from the vehicle body.