Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087837 M15A-FKS ENGINE MECHANICAL _0424629 ENGINE ASSEMBLY A

M15A-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the engine assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of engine assembly

·

Air leaks from intake system is repaired

·

Gas leaks from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Calibration
·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

CAUTION:
·
A340377C22
0.542,1.115 0.958,1.115 false 0.344,1.01 0.656,1.208 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the engine lifter


Because the weight of the engine with transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the engine lifter could drop and components could fall down.


·
A340359C12
0.375,1.135 0.75,1.281 true 0.135,1.031 0.448,1.229 0.313,0.198 10 false *a
*a High temperature areas


Do not touch the engine or exhaust manifold converter sub-assembly when they are hot.

·

Touching the engine or exhaust manifold converter sub-assembly when they are hot could result in burns.


·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 6.REMOVE FRONT WHEELS

Hide 51451A 7.REMOVE CENTER ENGINE UNDER COVER

Hide 51442C 8.REMOVE ENGINE UNDER COVER LH

Hide 51441C 9.REMOVE ENGINE UNDER COVER RH

Hide 51447D 10.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 12.DRAIN ENGINE COOLANT

Hide 13.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 14.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 15.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 16.REMOVE NO.1 FRONT VENTILATOR SEAL

Hide 55735A 17.REMOVE WATER GUARD PLATE LH

Hide 55701J 18.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 17705 19.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A458180C01
1.313,1.354 0.781,1.49 0.781,1.49 1.271,0.813 true 2.833,1.479 3.083,1.167 3.083,1.167 2.927,0.813 true 0.49,1.396 0.708,1.615 0.219,0.219 10 true *2 3.135,1.083 3.354,1.302 0.219,0.219 10 true *1
*1 Air Cleaner Cap Sub-assembly Clamp
*2 Guide


Disconnect the mass air flow meter connector.


b.

Disengage the clamp from the air cleaner cap sub-assembly.


c.

Disconnect the ventilation hose No. 2 from the air cleaner hose.


d.

Disengage the 2 air cleaner cap sub-assembly clamps.


e.

Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.


f.

Loosen the hose clamp and remove the air cleaner cap with air cleaner hose from the No. 1 inlet air duct sub-assembly.


Hide 17701 20.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A458181

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


b.
A465025

Remove the air cleaner case sub-assembly from the vehicle.


Hide 74404A 22.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A458183

Remove the 3 bolts and battery clamp sub-assembly from the vehicle.


Hide 23.DISCONNECT WIRE HARNESS

a.
A458184

Remove the 2 bolts to separate the engine wire from the vehicle.


b.
A458185

Remove the 2 nuts to separate the engine wire from the positive (+) battery terminal.


c.
A458186

Remove the No. 1 relay block cover from the engine room relay block.


d.
A458187

Disconnect the 3 connectors from the engine room relay block.


e.

Disengage the 2 claws to separate the engine wire from the engine room relay block.


Hide 16571C 24.DISCONNECT NO. 1 RADIATOR HOSE

A458189

a.

Slide the clip and disconnect the No. 1 radiator hose from the water outlet.


Hide 16572D 25.DISCONNECT NO. 2 RADIATOR HOSE

a.
A458190

Slide the clip and disconnect the No. 2 radiator hose from the water inlet with thermostat sub-assembly.


Hide 33820B 26.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)

Hide 33820B 27.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.
A458191

Remove the 2 clips A to disconnect the transmission control cable assembly from the manual transaxle assembly.


b.

Remove the 2 clips B to disconnect the transmission control cable assembly from control cable bracket assembly.


Hide 44777 28.DISCONNECT NO. 1 VACUUM HOSE CONNECTOR

Hide 23826 29.DISCONNECT NO.1 FUEL VAPOR FEED HOSE

a.
A458192

Disconnect the No. 1 fuel vapor feed hose from the fuel tank to canister tube.


Hide 77261D 30.DISCONNECT FUEL TANK TO CANISTER TUBE

a.
A458193

Disengage the clamp to separate the fuel tank to canister tube.


Hide 16290F 31.DISCONNECT NO.3 WATER BY-PASS HOSE ASSEMBLY

Hide 87245 32.DISCONNECT INLET HEATER WATER HOSE

Hide 23901 33.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A459850

Remove the No. 1 fuel pipe clamp for the fuel tube sub-assembly.


b.
A459852

Disconnect the fuel tube sub-assembly from the fuel pump assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 88703 34.DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 88704 35.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 36.SECURE STEERING WHEEL ASSEMBLY

Hide 45259A 37.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 38.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 51447D 39.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 17410 40.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 32101G 43.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for CVT)

Hide 31481A 44.DISCONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)

a.
A458194

Using a 10 mm union nut wrench, disconnect the bleeder clutch release tube from the No. 1 clutch hose.


b.

Remove the clip and disconnect the No. 1 clutch hose from the clutch flexible hose bracket.


Hide 45.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle and front suspension crossmember sub-assembly level.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the engine assembly from unexpectedly moving, securely support the engine assembly until it is secured to an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.
A458195

Remove the 2 bolts and nut and separate the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


c.
A458196C01
0,0 0.313,0.219 0.313,0.219 12 true *A 0,2.5 0.313,2.719 0.313,0.219 12 true *B
*A for CVT
*B for Manual Transaxle


for CVT:

Remove the 3 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.


d.

for Manual Transaxle:

Remove the 4 bolts and nut and separate the engine mounting insulator LH from the hybrid vehicle transaxle assembly.


e.
A458197

Remove the 10 bolts to separate the front suspension crossmember sub-assembly from the vehicle.


f.

Operate the engine lifter and remove the engine assembly with transaxle from the vehicle.

NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While lowering the engine assembly with transaxle from the vehicle, do not allow it to contact the vehicle.




Hide 12353 46.REMOVE ENGINE MOUNTING BRACKET CAP

a.
A466042

Turn over the engine mounting bracket cap to the upper part.


b.
A466043

While rotating in the direction shown in the diagram, remove the engine mounting bracket cap.


Hide 47.INSTALL ENGINE HANGERS

a.
A458200C02
0.271,0.969 0.615,0.969 true 2.229,0.979 2.573,0.979 true 0.083,0.885 0.396,1.042 0.313,0.156 10 false *1 1.99,0.875 2.229,1.073 0.24,0.198 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
V100135

Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 4 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-25030
No. 2 Engine Hanger 12282-25010
Bolt 91552-F1040



b.

Using an engine sling device and engine lift, secure the engine assembly with transaxle.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




Hide 12372A 48.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A458201

Remove the 5 bolts, nut and engine mounting insulator LH from the vehicle.


Hide 12305 49.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A458202

Remove the clamp and disconnect the air conditioner tube.


b.

Remove the 2 bolts, nut and engine mounting insulator sub-assembly RH from the vehicle.


Hide 50.REMOVE WATER HOSE (for CVT)

a.
A458203

Disengage the clamp from the engine assembly with transaxle.


b.

Slide the 3 clips and remove the water hose from the engine assembly with transaxle.


Hide 51.REMOVE WATER HOSE (for Manual Transaxle)

a.
A458204

Disengage the clamp from the engine assembly with transaxle.


b.

Slide the 3 clips and remove the water hose from the engine assembly with transaxle.


Hide 28100 52.REMOVE STARTER ASSEMBLY

Hide 11363A 53.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
A458205

Remove the flywheel housing side cover from the cylinder block sub-assembly.


Hide 82121 54.REMOVE ENGINE WIRE

a.
A458206

Remove the 6 bolts.


b.
A458207C02
0.063,0.031 0.438,0.271 0.375,0.24 12 false *A 0.073,2.365 0.448,2.604 0.375,0.24 12 false *B
*A for CVT
*B for Manual Transaxle


for CVT:

i.

Remove the 3 bolts.



c.

for Manual Transaxle:

i.

Remove the 4 bolts.



d.
A466015C01
0,0 0.26,0.219 0.26,0.219 12 true *A 0.042,2.188 0.302,2.406 0.26,0.219 12 true *B
*A for CVT
*B for Manual Transaxle


Remove the 2 bolts.


e.

Disconnect all the clamps and connectors and remove the engine wire from the engine assembly with transaxle.


Hide 32101B 57.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 31210 58.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31250 59.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 13405 60.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 19315 61.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 16361A 62.REMOVE FAN AND GENERATOR V BELT

Hide 16620D 63.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A458209

Remove the 2 bolts and V-ribbed belt tensioner assembly from the timing chain cover assembly.


Hide 88310 65.REMOVE COMPRESSOR WITH PULLEY ASSEMBLY

Hide 66.INSTALL ENGINE ASSEMBLY TO ENGINE STAND

a.

Install the engine assembly to an engine stand.


Hide 67.REMOVE ENGINE HANGERS

a.

Remove the 4 bolts, No. 1 engine hanger and No. 2 engine hanger.