Home › Engine / Hybrid System › M15A-FXE (LUBRICATION) › OIL PUMP
RM36W0E _51 Engine / Hybrid System _088718 M15A-FXE LUBRICATION _0422245 OIL PUMP A

M15A-FXE LUBRICATION  OIL PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 11320B 1.INSTALL NO. 2 TIMING CHAIN COVER ASSEMBLY

a.

Install a new oil pump gasket to the cylinder block sub-assembly.


b.

Clean the contact surfaces of the No. 2 timing chain cover assembly and timing chain cover assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.

A463141


c.
A467465

Apply seal packing in a continuous line to the No. 2 timing chain cover assembly as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Clean the surfaces with non-residue solvent before applying seal packing.

·

Install the No. 2 timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).




d.
A463139E01
1.719,0.719 1.875,0.917 0.156,0.198 10 true 1 0.594,0.344 0.75,0.542 0.156,0.198 10 false 2 0.563,0.76 0.719,0.958 0.156,0.198 10 false 3 0.635,1.135 0.792,1.333 0.156,0.198 10 false 4 0.958,1.521 1.094,1.698 0.135,0.177 10 true 5 0.76,1.708 0.917,1.906 0.156,0.198 10 false 6 0.688,2.094 0.844,2.292 0.156,0.198 10 false 7 0.646,2.406 0.802,2.604 0.156,0.198 10 false 8 0.719,3.052 0.875,3.25 0.156,0.198 10 false 9 1.063,3.229 1.396,3.396 0.333,0.167 10 false 10 1.979,3.229 2.271,3.396 0.292,0.167 10 false 11 2.438,2.823 2.781,3.01 0.344,0.188 10 false 12 2.458,2.365 2.667,2.552 0.208,0.188 10 true 13 2.51,2.042 2.719,2.229 0.208,0.188 10 true 14 2.49,1.625 2.698,1.813 0.208,0.188 10 false 15 2.646,1.104 2.854,1.292 0.208,0.188 10 false 16 2.708,0.354 2.917,0.542 0.208,0.188 10 false 17

Temporarily install the No. 2 timing chain cover assembly to the timing chain cover assembly with the 17 bolts.

NOTICE:

Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.



e.

Tighten the 17 bolts in the order shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


f.
A463142

Install the engine mounting bracket RH with the 3 bolts in the order shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

After applying seal packing to the No. 2 timing chain cover assembly, install the engine mounting bracket RH within 10 minutes.



Hide 2.INSTALL STRAIGHT SCREW PLUG

a.
A463138

Using a 10 mm hexagon wrench, install the straight screw plug to the No. 2 timing chain cover assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 11301C 3.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 11193 4.INSTALL SPARK PLUG TUBE GASKET

Hide 11201 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 13470 6.INSTALL CRANKSHAFT PULLEY ASSEMBLY

Hide 15370 8.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 10.INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 12262 12.INSTALL NO. 2 VENTILATION HOSE