Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _089412 M15A-FXE ENGINE MECHANICAL _0424638 ENGINE ASSEMBLY A

M15A-FXE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


HINT:

Perform "Inspection After Repair" after replacing the engine assembly.



PROCEDURE

Hide 2.REMOVE ENGINE FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 88370 3.INSTALL COMPRESSOR WITH MOTOR ASSEMBLY

Hide 19315 4.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 31270 6.INSTALL TRANSMISSION INPUT DAMPER ASSEMBLY

Hide 8.INSTALL WATER HOSE

a.

Install the water hose to the engine assembly with transaxle and slide the 3 clips to secure it.


Hide 82121 9.INSTALL ENGINE WIRE

a.

Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.


b.
A464814N01
0.625,1.208 0.781,1.406 0.156,0.198 10 true A 1.698,1.26 1.854,1.458 0.156,0.198 10 true A 1.958,1.885 2.115,2.083 0.156,0.198 10 true B

Install the 3 bolts.

Torque:
Bolt (A) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Bolt (B) : 20 N*m (204 kgf*cm, 15 ft.*lbf)


c.
A464815

Install the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.
A458206

Install the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11363A 11.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 12305 13.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A464813

Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


c.

Engage the clamp.


Hide G92A0A 14.INSTALL INVERTER RESERVE TANK ASSEMBLY

a.
A464812

Install the inverter reserve tank assembly to the engine mounting insulator sub-assembly RH with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 12372A 15.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A464811

Temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 4 bolts and nut in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 12353 17.INSTALL ENGINE MOUNTING BRACKET CAP

a.

Install the engine mounting bracket cap to the engine mounting bracket RH.


Hide 18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.
A458197N01
0.313,0.135 0.469,0.333 0.156,0.198 10 true B 3.021,0.125 3.177,0.323 0.156,0.198 10 true B 1.052,0.521 1.208,0.719 0.156,0.198 10 true A 2.25,0.521 2.406,0.719 0.156,0.198 10 true A 0.677,1.396 0.833,1.594 0.156,0.198 10 true A 2.646,1.406 2.802,1.604 0.156,0.198 10 true A 2.677,1.625 2.833,1.823 0.156,0.198 10 true A 0.667,1.615 0.823,1.813 0.156,0.198 10 true A 0.573,1.979 0.729,2.177 0.156,0.198 10 true A 2.76,1.979 2.917,2.177 0.156,0.198 10 true A

Connect the front suspension crossmember sub-assembly to the vehicle with the 10 bolts.

Torque:
Bolt (A) : 107.5 N*m (1096 kgf*cm, 79 ft.*lbf)
Bolt (B) : 30 N*m (306 kgf*cm, 22 ft.*lbf)


d.
A464810N01
0.729,0.854 0.885,1.052 0.156,0.198 10 true 1 2.375,1.031 2.531,1.229 0.156,0.198 10 true 2 2.26,0.427 2.417,0.625 0.156,0.198 10 true 3 2.26,1.615 2.417,1.813 0.156,0.198 10 true 4

Install the engine mounting insulator LH to the engine mounting bracket LH with the 3 bolts and nut in the order shown illustration.

Torque:
Bolt : 42 N*m (428 kgf*cm, 31 ft.*lbf)
Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


e.
A192239C21
1.427,1.917 1.594,1.917 1.594,1.917 1.885,1.573 false 1.229,1.823 1.542,2.063 0.313,0.24 10 *a
*a Adhesive


Apply adhesive to the 2 or 3 threads at the tip of each of the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



f.
A464809C01
0.563,0.458 1.188,0.677 0.625,0.219 10 true 1 (*a), 3 2.365,0.688 2.563,0.896 0.198,0.208 10 true 2
*a Temporarily Tighten


Install the 2 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.
A464808N01
1.177,0.792 1.333,0.99 0.156,0.198 10 true 1 2.469,1.198 2.625,1.396 0.156,0.198 10 true 2 2.448,0.708 2.604,0.906 0.156,0.198 10 true 3

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut in the order shown illustration.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 17410 20.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 45260 21.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 22.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 88704 23.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 24.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 23901 25.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
A459851

Connect the fuel tube sub-assembly to the fuel pump assembly.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION


b.
A459849

Install the No. 1 fuel pipe clamp to the fuel tube sub-assembly.


Hide 87245 26.CONNECT INLET HEATER WATER HOSE

Hide 16290F 27.CONNECT NO.3 WATER BY-PASS HOSE ASSEMBLY

Hide 77261D 28.CONNECT FUEL TANK TO CANISTER TUBE

a.

Engage the clamp to connect the fuel tank to canister tube to the engine wire.


Hide 23826 29.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the fuel tank to canister tube.


Hide G922F 30.CONNECT OUTLET NO. 1 HYBRID WATER PUMP HOSE

a.

Connect the outlet No. 1 hybrid water pump hose to the motor cooling cooler and slide the clip to secure it.


Hide G922H 31.CONNECT INLET HYBRID RADIATOR HOSE

a.

Connect the inlet hybrid radiator hose to the motor cooling cooler and slide the clip to secure it.


Hide 16572D 32.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet sub-assembly and slide the clip to secure it.


Hide 16571C 33.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


Hide 33820B 34.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Install the transmission control cable assembly to the hybrid vehicle transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Engage the clamp to connect the transmission control cable assembly.


c.

Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.


d.

Install the transmission control cable assembly to the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 35.CONNECT ENGINE WIRE

a.

Engage the clamp to connect the engine wire to the vehicle.


b.

Connect the engine wire to the vehicle with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Engage the clamp.


d.

Engage the 4 claws to connect the engine wire to the engine room relay block.


e.

Install the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Connect the 2 connectors to the engine room relay block.


Hide 82662A 36.INSTALL NO. 1 RELAY BLOCK COVER

a.

Install the No. 1 relay block cover to the engine room relay block.


Hide G9200 37.INSTALL INVERTER WITH CONVERTER ASSEMBLY

Hide 39.ADD ENGINE COOLANT (for Engine)

Hide 41.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 46.INSPECT FOR ENGINE OIL LEAK

Hide 48.INSPECT FOR COOLANT LEAK (for Engine)

Hide 53.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 51442C 54.INSTALL ENGINE UNDER COVER LH

Hide 51441C 55.INSTALL ENGINE UNDER COVER RH

Hide 51451A 56.INSTALL CENTER ENGINE UNDER COVER

Hide 57.INSTALL FRONT WHEELS

Hide 58. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 59.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 60. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function thatcompletes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART