Home › Engine / Hybrid System › M15A-FXE (ENGINE MECHANICAL) › ENGINE UNIT
RM36W0E _51 Engine / Hybrid System _089412 M15A-FXE ENGINE MECHANICAL _0424639 ENGINE UNIT A

M15A-FXE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.
A466616C01
2.438,3.635 2.75,3.833 0.313,0.198 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in 2 new straight pins to the No. 2 timing chain cover assembly.

Standard Protrusion Height:

5.0 to 7.0 mm (0.197 to 0.276 in.)



Hide 2.INSTALL RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A458981C01
2.458,2.594 2.771,2.75 0.313,0.156 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in 6 new ring pins to the stiffening crankcase assembly.

Standard Protrusion Height:

3.5 to 4.5 mm (0.138 to 0.177 in.)



b.
A458982C01
2.344,2.552 2.656,2.75 0.313,0.198 10 false *a
*a Protrusion Height


Using a plastic hammer, tap in 8 new ring pins to the camshaft housing sub-assembly.

Standard Protrusion Height:

3.2 to 4.3 mm (0.126 to 0.169 in.)



Hide 3.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A458983C01
1.615,2.563 1.927,2.719 0.313,0.156 10 false *a 2.333,2.771 2.646,2.927 0.313,0.156 10 false *b 1.604,2.896 1.917,3.052 0.313,0.156 10 false *a
*a 9 mm (0.354 in.)
*b 19 mm (0.748 in.)


Using an E6 "TORX" socket wrench, install the 2 stud bolts to the stiffening crankcase assembly.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
A458984C01
1.458,2.531 1.771,2.688 0.313,0.156 10 false *a 1.49,3.031 1.802,3.188 0.313,0.156 10 false *b 2.438,2.781 2.75,2.938 0.313,0.156 10 false *c
*a 21 mm (0.827 in.)
*b 9 mm (0.354 in.)
*c 34 mm (1.34 in.)


w/ Stud Bolt

i.

Using an E6 "TORX" socket wrench, install the stud bolt to the timing chain cover assembly.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)



c.
A458985C01
1.594,2.573 1.906,2.729 0.313,0.156 10 false *a 1.604,2.927 1.917,3.083 0.313,0.156 10 false *b 2.333,2.781 2.646,2.938 0.313,0.156 10 false *c
*a 14 mm (0.551 in.)
*b 13 mm (0.512 in.)
*c 29 mm (1.063 in.)


Using an E8 "TORX" socket wrench, install the stud bolt to the cylinder head sub-assembly.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 4.INSTALL STRAIGHT SCREW PLUG

a.
A459773

Using a 10 mm hexagon socket wrench, install the straight screw plug and new a gasket to the stiffening crankcase assembly.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 11420 5.INSTALL STIFFENING CRANKCASE ASSEMBLY

a.
A458988C01
2.625,0.604 3.073,1.208 3.073,1.208 2.625,1.656 true 3.125,1.115 3.375,1.313 0.25,0.198 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Dimension:
Area Specified Condition
Continuous Line 2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not add engine oil for at least 2 hours after the installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).




b.
A458989C01
0.094,0.083 0.406,0.24 0.313,0.156 10 false *a 1.521,2 1.677,2.177 0.156,0.177 10 false B 0.969,1.958 1.104,2.125 0.135,0.167 10 true A 1.885,1.979 2.042,2.156 0.156,0.177 10 false C 2.333,1.927 2.49,2.104 0.156,0.177 10 false B 1.01,0 1.167,0.177 0.156,0.177 10 false C 1.458,0.042 1.583,0.219 0.125,0.177 10 false C 1.906,0.073 2.042,0.24 0.135,0.167 10 false C 2.323,0.146 2.458,0.313 0.135,0.167 10 false B
*a Bolt Type


Temporarily install the stiffening crankcase assembly with the 8 bolts.

Bolt Length :
Item Length
Bolt (A) 170 mm (6.69 in.)
Bolt (B) 120 mm (4.72 in.)
Bolt (C) 40 mm (1.57 in.)



c.
A458989C02
0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 2.344,0.135 2.469,0.302 0.125,0.167 10 false 5 1.458,0.042 1.583,0.208 0.125,0.167 10 false 1 1.917,0.063 2.042,0.229 0.125,0.167 10 false 3 1,1.938 1.125,2.104 0.125,0.167 10 true 8 2.344,1.917 2.542,2.094 0.198,0.177 10 false 6 1.531,2 1.656,2.167 0.125,0.167 10 false 4 1.885,1.969 2.01,2.135 0.125,0.167 10 false 2 1.021,0 1.146,0.167 0.125,0.167 10 false 7
*a Tightening Order


Tighten the 8 bolts in the order shown in the illustration to install the stiffening crankcase assembly.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 89491 6.INSTALL ENGINE OIL LEVEL SENSOR

Hide 15104 7.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new oil strainer gasket.


b.
A466455

Using an 8 mm socket wrench, install the oil strainer sub-assembly and oil strainer gasket to the stiffening crankcase assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101 8.INSTALL OIL PAN SUB-ASSEMBLY

a.
A458990C01
2.865,2.563 2.542,2.271 true 2.083,0.833 2.24,1.031 0.156,0.198 10 false A 2.052,1.26 2.208,1.458 0.156,0.198 10 true A 2.906,2.552 3.219,2.75 0.313,0.198 10 false *a 1.771,2.75 2.229,2.958 0.458,0.208 10 false A - A 1.365,3.083 1.677,3.281 0.313,0.198 10 false *b 1.375,3.396 1.688,3.594 0.313,0.198 10 false *c
*a Seal Packing
*b 4.5 mm (0.177 in.)
*c 2.5 to 3.5 mm (0.0984 to 0.138 in.)


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts and nuts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).




b.
A458856C02
1.333,1.552 1.833,1.125 1.833,1.125 2.188,1.646 true 1.74,0.927 1.927,1.094 0.188,0.167 10 true *a 2.094,0.031 2.198,0.188 0.104,0.156 10 true 3 2.677,0.292 2.781,0.448 0.104,0.156 10 true 4 2.656,1.031 2.76,1.188 0.104,0.156 10 true 5 2.656,1.396 2.792,1.552 0.135,0.156 10 true 6 1.24,1.865 1.375,2.021 0.135,0.156 10 true 9 1.771,1.865 1.906,2.021 0.135,0.156 10 true 8 2.073,1.969 2.396,2.135 0.323,0.167 10 false 1, 7 0.563,1.563 0.76,1.719 0.198,0.156 10 true 10 1.063,0.479 1.26,0.635 0.198,0.156 10 true 12 1.125,0.208 1.5,0.365 0.375,0.156 10 true 2, 13 0.615,0.563 0.813,0.719 0.198,0.156 10 true 11
*a Nut


Install the oil pan sub-assembly with the 9 bolts and 2 nuts in several steps in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101A 9.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and the oil pan drain plug to the oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15600A 10.INSTALL OIL FILTER UNION

a.
A458855

Using a 12 mm hexagon socket wrench, install the oil filter union to the stiffening crankcase assembly.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)


Hide 15601 11.INSTALL OIL FILTER SUB-ASSEMBLY

Hide 11445 13.INSTALL CYLINDER BLOCK WATER JACKET SPACER

a.
A458854

Install the cylinder block water jacket spacer to the exhaust side of the cylinder block sub-assembly.


Hide 11101 15.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:

The cylinder head set bolts are tightened in 3 progressive steps.


a.

Place the cylinder head sub-assembly on the cylinder block sub-assembly.

NOTICE:
·

Ensure that the contact surface of the cylinder head sub-assembly is free of oil.

·

Place the cylinder head sub-assembly on the cylinder block sub-assembly gently in order not to damage the cylinder head gasket with the bottom of the cylinder head sub-assembly.




b.
A458853C02
0.583,0.427 0.74,0.625 0.156,0.198 10 false A 0.563,1.594 0.719,1.792 0.156,0.198 10 false A 2.708,1.552 2.865,1.75 0.156,0.198 10 true A 2.719,0.438 2.875,0.635 0.156,0.198 10 true A 1.365,0.281 1.521,0.479 0.156,0.198 10 true B 1.865,0.281 2.021,0.479 0.156,0.198 10 true B 1.875,1.75 2.031,1.948 0.156,0.198 10 true B 1.375,1.74 1.531,1.938 0.156,0.198 10 true B
V100136

Front of Engine


Install the 8 plate washers to the 8 cylinder head set bolts.

Bolt Length :
Item Length
Bolt (A) 129.1 to 130.9 mm (5.08 to 5.15 in.)
Bolt (B) 139.1 to 140.9 mm (5.48 to 5.55 in.)



c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head set bolts.


d.

Step 1:

i.
A458853C03
1.385,1.74 1.521,1.938 0.135,0.198 10 true 1 1.875,0.281 2.01,0.479 0.135,0.198 10 true 2 1.875,1.75 2.01,1.948 0.135,0.198 10 true 3 1.375,0.271 1.51,0.469 0.135,0.198 10 true 4 2.708,1.563 2.844,1.76 0.135,0.198 10 true 5 0.615,0.479 0.75,0.677 0.135,0.198 10 false 6 2.719,0.448 2.854,0.646 0.135,0.198 10 true 8 0.594,1.615 0.729,1.813 0.135,0.198 10 false 7
V100136

Front of Engine


Using a 12 mm socket wrench, install and uniformly tighten the 8 cylinder head set bolts in several steps in the order shown in the illustration.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

NOTICE:

Be careful not to drop the plate washers into the cylinder head sub-assembly.




e.

Step 2:

i.
A196910C18
1.24,1.563 1.5,1.156 false 1.094,1.563 1.271,1.75 0.177,0.188 10 false *a 0.896,0.375 1.198,0.531 0.302,0.156 10 false 90° 2.583,0.375 2.885,0.531 0.302,0.156 10 false 90°
*a Paint Mark
V100136

Front of Engine


Mark each cylinder head set bolt head with paint as shown in the illustration.


ii.

Tighten the cylinder head set bolts 90° in the order shown in step 1.



f.

Step 3:

i.

Tighten the cylinder head set bolts another 90° in the order shown in step 1.


ii.

Check that the paint marks are now facing rearward.

HINT:

Perform inspection after repair after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Hide 13716 16.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem cap ends.


b.
A458851

Install the 12 valve stem caps to the cylinder head sub-assembly.

NOTICE:
·

Install the same parts in the same combination to their original locations.

·

Do not drop the valve stem caps into the cylinder head sub-assembly.




Hide 13750 17.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect the 12 valve lash adjuster assemblies before installing them.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION


b.
A458851

Install the 12 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install the same parts in the same combination to their original locations.



Hide 13801 18.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A400400C01
2.531,0.906 2.896,0.906 false 1.885,0.406 2.052,0.24 2.052,0.24 2.208,0.24 false 0.677,0.76 1.042,0.76 false 2.26,0.146 2.573,0.344 0.313,0.198 10 false *1 2.958,0.823 3.271,1.021 0.313,0.198 10 false *2 0.479,0.667 0.792,0.865 0.313,0.198 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem Cap


Apply engine oil to the valve lash adjuster assembly tips and valve stem caps.


b.

Install the 12 No. 1 valve rocker arm sub-assemblies as shown in the illustration.

NOTICE:

Install the same parts in the same combination to their original locations.



Hide 13502B 19.INSTALL EXHAUST CAMSHAFT SUB-ASSEMBLY

HINT:

Perform inspection after repair after replacing the exhaust camshaft sub-assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft journals and camshaft housing sub-assembly.


b.

Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.


c.

Install the exhaust camshaft sub-assembly to the camshaft housing sub-assembly.


Hide 13501A 20.INSTALL INTAKE CAMSHAFT SUB-ASSEMBLY

HINT:

Perform inspection after repair after replacing the intake camshaft sub-assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.

Clean the camshaft journals, camshaft housing sub-assembly and camshaft bearing caps.


b.

Apply a light coat of engine oil to the camshaft journals, camshaft housing sub-assembly andcamshaft bearing caps.


c.

Install the intake camshaft sub-assembly to the camshaft housing sub-assembly.


Hide 21.INSTALL CAMSHAFT BEARING CAP

a.
A466472C01
1.344,1.854 1.344,1.438 true 1.875,1.875 1.875,1.458 true 1.271,1.865 1.583,2.063 0.313,0.198 10 false *a 1.813,1.885 2.125,2.083 0.313,0.198 10 false *b
*a 2
*b 3 to 4


Place the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap in their correct locations.


b.
A458847N01
2.052,0.844 2.167,1.021 0.115,0.177 10 true 5 1.573,1.354 1.688,1.542 0.115,0.188 10 true 1 1.052,1.344 1.167,1.531 0.115,0.188 10 true 3 0.563,1.333 0.729,1.531 0.167,0.198 10 false 7 1.01,0.615 1.125,0.781 0.115,0.167 10 true 4 1.573,0.563 1.688,0.729 0.115,0.167 10 true 2 2.042,1.677 2.156,1.844 0.115,0.167 10 true 6

Uniformly tighten the 7 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


c.

Check the torque of each bolt again.


Hide 11103 22.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A400401C01
1,0.427 1.427,0.427 false 2.01,0.198 2.385,0.115 2.385,0.115 2.604,0.115 false 2.292,0.802 2.719,0.802 false 2.344,2.521 2.771,2.521 false 1.979,1.969 2.208,1.802 2.208,1.802 2.365,1.802 false 1.042,2.146 1.469,2.146 false 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 0.188,1.781 0.5,1.979 0.313,0.198 10 false *b 2.688,0.052 3,0.25 0.313,0.198 10 false *1 2.448,1.688 2.76,1.885 0.313,0.198 10 false *1 0.813,0.333 1.125,0.531 0.313,0.198 10 false *2 0.865,2.052 1.177,2.25 0.313,0.198 10 false *2 2.781,0.698 3.094,0.896 0.313,0.198 10 false *3 2.844,2.438 3.156,2.635 0.313,0.198 10 false *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Stem Cap
*3 Valve Lash Adjuster Assembly
*a Incorrect
*b Correct


Check that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


b.
A466457C01
1.26,0.49 1.698,0.156 true 1.74,0.042 2.052,0.198 0.313,0.156 10 false *a
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).




c.
A458993C01
0.969,0.438 1.281,0.635 0.313,0.198 10 false *a 1.74,0.573 1.938,0.781 0.198,0.208 10 false *b
*a 12° to 42°
*b 83° to 113°


Position the intake camshaft sub-assembly and exhaust camshaft sub-assembly as shown in the illustration.


d.
A458845N02
0.427,0.927 0.573,1.104 0.146,0.177 10 true B 0.563,0.156 0.719,0.354 0.156,0.198 10 false B 1.344,0.094 1.5,0.271 0.156,0.177 10 true B 2.031,0.104 2.177,0.281 0.146,0.177 10 true B 2.854,0.25 3.01,0.448 0.156,0.198 10 false B 0.896,1.25 1.042,1.448 0.146,0.198 10 true A 0.573,1.74 0.729,1.938 0.156,0.198 10 false B 1.323,1.844 1.479,2.042 0.156,0.198 10 true B 1.833,1.844 1.969,2.021 0.135,0.177 10 true B 2.708,1.708 2.875,1.906 0.167,0.198 10 true B 2.885,0.948 3.052,1.146 0.167,0.198 10 false B 1.406,1.25 1.552,1.448 0.146,0.198 10 true A 1.948,1.219 2.104,1.417 0.156,0.198 10 true B 1.833,0.104 1.99,0.281 0.156,0.177 10 true B

Temporarily install the camshaft housing sub-assembly with the 14 bolts.

Bolt Length :
Item Length
Bolt (A) 40 mm (1.57 in.)
Bolt (B) 65 mm (2.56 in.)



e.
A458845N03
0.5,0.156 0.719,0.365 0.219,0.208 10 false 14 0.51,1.74 0.719,1.927 0.208,0.188 10 false 13 0.396,0.948 0.583,1.156 0.188,0.208 10 true 12 2.833,0.24 3.073,0.458 0.24,0.219 10 false 11 2.865,0.948 3.104,1.177 0.24,0.229 10 false 10 2.052,0.146 2.177,0.313 0.125,0.167 10 true 9 2.708,1.677 2.844,1.854 0.135,0.177 10 false 8 1.969,1.24 2.083,1.417 0.115,0.177 10 true 7 1.344,0.104 1.49,0.26 0.146,0.156 10 true 3 1.844,1.844 1.979,2.021 0.135,0.177 10 true 5 1.427,1.271 1.552,1.438 0.125,0.167 10 true 4 0.896,1.25 1.021,1.427 0.125,0.177 10 true 1 1.313,1.844 1.438,2.021 0.125,0.177 10 true 2 1.833,0.125 1.958,0.292 0.125,0.167 10 true 6

Install the camshaft housing sub-assembly, and then tighten the 14 bolts in several steps in the order shown in the illustration.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)

NOTICE:
·

Do not add engine oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

After installation, if the seal packing has seeped out, wipe it off.




Hide 13471A 23.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A378000

Using a plastic hammer, tap in the 2 crankshaft timing gear keys.

HINT:

Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.



Hide 13478 24.INSTALL CRANKSHAFT PULLEY SPACER

a.

Install the crankshaft pulley spacer with the crankshaft.


Hide 11310 25.INSTALL TIMING CHAIN COVER ASSEMBLY

a.

Clean the contact surfaces of the timing chain cover assembly, cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly, and confirm that no oil, moisture, or other foreign matter is on the surfaces.

A466458C01
0.688,0.427 1,0.583 0.313,0.156 10 false *a 4.083,0.427 4.396,0.583 0.313,0.156 10 false *b
*a Timing Chain Cover Assembly Side *b Engine Assembly Side



b.

Apply seal packing in a continuous line to the timing chain cover assembly as shown in the illustration.

A466459C01
4.26,2.229 4.833,1.927 4.833,1.927 4.396,1.448 true 3.25,1.75 2.594,2.01 2.594,2.01 3.656,1.885 true 4.885,1.823 5.198,2.021 0.313,0.198 10 false *a 2.396,1.906 2.708,2.104 0.313,0.198 10 false *b 1.802,0.417 2.115,0.615 0.313,0.198 10 false *c 5.531,0.427 5.844,0.625 0.313,0.198 10 false *c 4.281,0.052 4.594,0.25 0.313,0.198 10 false *d 2.229,2.698 2.542,2.896 0.313,0.198 10 false *e 5.104,2.708 5.417,2.906 0.313,0.198 10 false *e 6.469,2.01 6.781,2.208 0.313,0.198 10 false *f 0.531,1.979 0.844,2.177 0.313,0.198 10 false *f 2.188,4.146 2.5,4.344 0.313,0.198 10 false *g 1.198,4.906 1.51,5.104 0.313,0.198 10 false *h 1.563,3.833 2.26,4.063 0.698,0.229 10 false A - A (★) 3.031,0.646 3.344,0.844 0.313,0.198 10 false ★ 4.563,0.281 4.875,0.479 0.313,0.198 10 false ★ 4.5,0.927 4.677,1.104 0.177,0.177 10 true ★ 4.135,2.896 4.302,3.073 0.167,0.177 10 true ★ 3.198,2.865 3.365,3.021 0.167,0.156 10 true ★ 2.948,3.281 3.104,3.479 0.156,0.198 10 true A 3.25,3.281 3.406,3.479 0.156,0.198 10 true A
*a 2.5 to 3.5 mm (0.0984 to 0.138 in.) *b 2.0 to 6.0 mm (0.0787 to 0.236 in.)
*c 10 mm (0.394 in.) *d 30 mm (1.181 in.)
*e 20 mm (0.787 in.) *f 344.2 mm (1.13 ft.)
*g 4.0 to 6.0 mm (0.157 to 0.236 in.) *h 3.0 to 4.0 mm (0.118 to 0.157 in.)
V100155

Seal Packing - -


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Clean the surfaces with non-residue solvent before applying seal packing.

·

Install the timing chain cover assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not add oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.

·

Make sure that the diameter at the start and end of each line of seal packing is 5 +/- 2 mm (0.197 +/- 0.0787 in.).




c.
A458840N05
2.438,0.958 2.604,1.177 0.167,0.219 10 false B 1.76,1.271 1.938,1.458 0.177,0.188 10 true A 2.271,1.51 2.448,1.698 0.177,0.188 10 true A 2.406,1.885 2.583,2.073 0.177,0.188 10 true A 2.406,2.208 2.583,2.396 0.177,0.188 10 true A 2.281,2.375 2.458,2.563 0.177,0.188 10 true A 2.396,2.625 2.573,2.813 0.177,0.188 10 false A 1.781,3.167 1.958,3.354 0.177,0.188 10 false A 1.375,3.167 1.552,3.354 0.177,0.188 10 false A 0.646,2.677 0.823,2.865 0.177,0.188 10 false A 0.813,2.271 0.99,2.458 0.177,0.188 10 false A 0.802,1.896 0.979,2.083 0.177,0.188 10 false A 0.896,1.51 1.073,1.698 0.177,0.188 10 false A 2.573,0.583 2.74,0.802 0.167,0.219 10 false B 2.198,0.115 2.365,0.333 0.167,0.219 10 false B 1.948,0.5 2.104,0.688 0.156,0.188 10 true B 1.396,0.604 1.552,0.792 0.156,0.188 10 true B 0.844,0.979 1.01,1.198 0.167,0.219 10 false B 0.885,0.76 1.052,0.979 0.167,0.219 10 false B 0.76,0.563 0.927,0.781 0.167,0.219 10 false B

Temporarily install the timing chain cover assembly with the 20 bolts.

Bolt Length:
Bolt Length
(A) 30 mm (1.18 in.)
(B) 45 mm (1.77 in.)


NOTICE:

Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.



d.
A458840N02
1.323,0.563 1.51,0.76 0.188,0.198 10 true 14 1.74,1.25 1.927,1.427 0.188,0.177 10 true 11 1.906,0.479 2.104,0.656 0.198,0.177 10 true 13 2.135,0.073 2.313,0.26 0.177,0.188 10 false 20 2.542,0.521 2.74,0.708 0.198,0.188 10 false 19 2.417,0.906 2.604,1.083 0.188,0.177 10 false 18 2.271,1.5 2.49,1.677 0.219,0.177 10 true 12 2.396,1.844 2.542,2.01 0.146,0.167 10 true 1 2.385,2.177 2.531,2.344 0.146,0.167 10 true 4 2.25,2.354 2.396,2.521 0.146,0.167 10 true 5 2.354,2.604 2.5,2.771 0.146,0.167 10 true 6 1.76,3.156 1.906,3.323 0.146,0.167 10 true 7 1.354,3.125 1.5,3.292 0.146,0.167 10 true 8 0.615,2.646 0.74,2.865 0.125,0.219 10 false 9 0.802,2.24 0.927,2.458 0.125,0.219 10 false 2 0.792,1.865 0.917,2.083 0.125,0.219 10 false 3 0.792,1.469 0.99,1.688 0.198,0.219 10 false 10 0.719,0.531 0.927,0.719 0.208,0.188 10 false 17 0.802,0.74 1.021,0.927 0.219,0.188 10 false 16 0.792,0.948 1,1.135 0.208,0.188 10 false 15

Tighten the 20 bolts in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 13070A 26.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

HINT:

Perform inspection after repair after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A458998C01
0.99,0.635 1.792,0.219 true 2.021,1 2.448,0.688 true 1.802,0.094 2.115,0.292 0.313,0.198 10 false *a 2.479,0.542 2.792,0.74 0.313,0.198 10 false *b
*a Knock Pin Hole
*b Knock Pin


Align and fit the knock pin of the exhaust camshaft sub-assembly to the knock pin hole of the camshaft timing exhaust gear assembly.


b.

Using a wrench, hold the hexagonal portion of the exhaust camshaft sub-assembly.

NOTICE:
·

Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.

·

Do not disassemble the camshaft timing exhaust gear assembly.




c.
A458838

Using a 5 mm hexagon socket wrench, install the camshaft timing exhaust gear assembly with the 3 bolts and install the camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 27.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.

Temporarily install the crankshaft pulley bolt.


b.
A458999C01
1.365,1.188 1.365,1.521 true 0.844,0.469 1.052,0.688 0.208,0.219 10 true *a 1.26,1.542 1.521,1.75 0.26,0.208 10 true *1
*1 Crankshaft Timing Gear Key
*a 95°


Rotate the crankshaft 44.2° counterclockwise to position the crankshaft timing gear key as shown in the illustration.


c.
A459000C01
0.948,1.292 0.635,1.125 0.635,1.125 0.99,1.01 true 2.51,1.333 2.115,1.177 2.115,1.177 2.521,1.094 true 0.458,1.021 0.635,1.219 0.177,0.198 10 true *a 1.927,1.042 2.104,1.24 0.177,0.198 10 true *a
*a Timing Mark


Check that the timing marks of the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.


Hide 13561 28.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 13559 29.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper with the bolt.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 13540 30.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

HINT:

After replacing or removing and installing the No. 1 chain tensioner assembly, an abnormal noise may occur at start up until the oil in the line has had time to replenish.


a.
A466464C02
0.052,0.042 0.427,0.281 0.375,0.24 12 false *A 0.052,2.406 0.427,2.646 0.375,0.24 12 false *B
*A w/ Stud Bolt
*B w/o Stud Bolt


w/ Stud Bolt:

i.

Install the No. 1 chain tensioner assembly with the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

w/o Stud Bolt:

i.

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 13506 31.INSTALL CHAIN SUB-ASSEMBLY

a.

Remove the crankshaft pulley bolt.


b.

Install the crankshaft timing sprocket and chain sub-assembly.


c.
A459001C01
2.01,1.083 1.917,0.833 1.917,0.833 1.75,0.833 true 2.219,1.135 2.552,1.135 true 2.563,1.021 2.781,1.229 0.219,0.208 10 true *a 1.542,0.708 1.74,0.917 0.198,0.208 10 true *b
*a Paint Mark (Yellow)
*b Timing Mark


Align the paint mark (yellow) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket and install the chain sub-assembly to the crankshaft timing sprocket.


d.
A459002C01
0.854,3.396 0.917,3.083 0.917,3.083 1.083,3.083 true 0.667,3.833 0.833,3.833 0.833,3.833 0.854,3.615 true 1.094,2.969 1.292,3.156 0.198,0.188 10 true *a 0.469,3.719 0.646,3.896 0.177,0.177 10 true *b
*a Paint Mark (Orange)
*b Timing Mark
V113147

Turn


Using the hexagonal portion of the exhaust camshaft sub-assembly, rotate the exhaust camshaft sub-assembly counterclockwise with a wrench, align the timing mark of the camshaft timing exhaust gear assembly with the paint mark (orange) of the chain sub-assembly, and install the chain sub-assembly to the camshaft timing exhaust gear assembly.


Hide 13050 32.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

Perform inspection after repair after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A459003C01
1.927,1.375 2.5,1.083 2.5,1.083 2.667,1.083 true 2.698,0.969 3.01,1.167 0.313,0.198 10 false *a
*a Loosen


Hold the hexagonal portion of the exhaust camshaft sub-assembly with a wrench and turn the camshaft timing exhaust gear assembly clockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and crankshaft timing sprocket as shown in the illustration.


b.
A466473C01
0.563,1.469 0.729,1.469 0.729,1.469 1.031,1.208 true 1.156,0.844 1.521,0.583 1.521,0.583 1.771,0.583 true 0.375,1.365 0.563,1.563 0.188,0.198 10 true *a 1.854,0.5 2.063,0.698 0.208,0.198 10 true *b
*a Paint Mark (Orange)
*b Timing Mark


Align the paint mark (orange) of the chain sub-assembly with the timing mark of the camshaft timing gear assembly and install the chain sub-assembly to the camshaft timing gear assembly.


c.
A466474C01
1.115,0.677 1.854,0.229 1.854,0.229 2.25,0.229 true 1.938,1.292 2,1.073 2,1.073 2.208,1.073 false 2.333,0.125 2.646,0.323 0.313,0.198 10 false *a 2.24,0.99 2.552,1.188 0.313,0.198 10 false *b
*a Knock Pin Hole
*b Knock Pin


Align and fit the knock pin of the intake camshaft sub-assembly to the knock pin hole of the camshaft timing gear assembly.


d.
A459004C01
1.552,0.021 1.865,0.177 0.313,0.156 10 false *a
*a Hold
V113147

Turn


Using a wrench, hold the hexagonal portion of the intake camshaft sub-assembly.

NOTICE:
·

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.




e.

Using a 10 mm bi-hexagonal wrench, install the camshaft timing gear assembly with the bolt.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


f.

Remove the hexagon wrench with the No. 1 chain tensioner assembly.


Hide 33.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13519 34.INSTALL OIL PUMP DRIVE GEAR

a.

Install the oil pump drive gear to the crankshaft.


Hide 11320B 35.INSTALL NO. 2 TIMING CHAIN COVER ASSEMBLY

Hide 11193 37.INSTALL SPARK PLUG TUBE GASKET

a.
A466403

Install 3 new spark plug tube gaskets to the cylinder head cover sub-assembly.


Hide 11201 38.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A424997

Install a new camshaft bearing cap oil hole gasket to the No. 1 camshaft bearing cap.

NOTICE:

Remove any oil from the contact surfaces.



b.

Install 5 new cylinder head cover gaskets to the cylinder head cover sub-assembly.

NOTICE:

Remove any oil from the contact surfaces.



c.
A459005C01
0.583,1.24 0.25,1.396 0.25,1.396 0.604,1.052 true 0.948,2.375 0.521,1.948 0.521,1.948 0.948,1.594 true 2.302,2.448 1.729,3 1.729,3 0.896,2.427 true 2.188,2.375 1.719,3.01 1.719,3.01 1.052,2.365 true 2.229,2.406 2.708,1.938 2.708,1.938 2.417,1.406 true 2.656,1.052 2.979,1.438 2.979,1.438 2.677,1.208 true 0.073,1.292 0.281,1.5 0.208,0.208 10 false *a 1.656,3.01 1.865,3.188 0.208,0.177 10 true *b 0.344,1.823 0.552,2.031 0.208,0.208 10 false *a 2.74,1.833 2.948,2.042 0.208,0.208 10 false *a 3,1.344 3.208,1.552 0.208,0.208 10 false *a
*a Seal Packing Diameter: 3.0 to 6.0 mm (0.118 to 0.236 in.)
*b Mark
V100143

Seal Packing


Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Packing Diameter:

3.0 to 6.0 mm (0.118 to 0.236 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




d.
A459006N01
0.771,2.281 1.083,2.479 0.313,0.198 10 false 10 1.292,2.302 1.667,2.5 0.375,0.198 10 false 5, 11 2.01,2.323 2.323,2.521 0.313,0.198 10 false 12 2.542,2.323 2.854,2.521 0.313,0.198 10 false 13 2.927,3.219 3.24,3.417 0.313,0.198 10 false 14 2.823,3.781 3.135,3.979 0.313,0.198 10 false 15 2.167,4.083 2.385,4.26 0.219,0.177 10 true 16 1.698,4.083 2.063,4.26 0.365,0.177 10 true 6, 17 1.917,3.604 2.073,3.781 0.156,0.177 10 true 2 1.635,3.344 1.771,3.531 0.135,0.188 10 true 4 1.219,3.333 1.354,3.521 0.135,0.188 10 true 3 1.865,2.698 2,2.885 0.135,0.188 10 true 1 0.438,3.208 0.615,3.417 0.177,0.208 10 false 9 0.542,3.979 0.677,4.167 0.135,0.188 10 true 8 1.26,4.104 1.417,4.281 0.156,0.177 10 true 7 0.448,0.906 0.625,1.115 0.177,0.208 10 false A 0.615,1.729 0.76,1.917 0.146,0.188 10 true A 1.281,1.781 1.427,1.969 0.146,0.188 10 true A 1.781,1.781 1.927,1.969 0.146,0.188 10 true A 2.198,1.781 2.344,1.969 0.146,0.188 10 true A 2.844,1.448 3.021,1.656 0.177,0.208 10 false A 2.938,0.917 3.115,1.125 0.177,0.208 10 false A 1.938,1.292 2.083,1.479 0.146,0.188 10 true B 1.625,1.042 1.771,1.229 0.146,0.188 10 true B 1.229,1.063 1.375,1.25 0.146,0.188 10 true B 1.854,0.406 2,0.594 0.146,0.188 10 true B 0.802,0 0.979,0.208 0.177,0.208 10 false A 1.385,0 1.563,0.208 0.177,0.208 10 false A 2.031,0 2.208,0.208 0.177,0.208 10 false A 2.573,0 2.75,0.177 0.177,0.177 10 false A

Using an 8 mm socket wrench, install the 2 camshaft position sensors (for Exhaust Side and for Intake Side) and cylinder head cover sub-assembly with 4 new bolts (B) and the 11 bolts (A) in the order shown in the illustration.

Bolt Length:
Bolt Length Thread Diameter
(A) 23.5 mm (0.925 in.) 6 mm (0.24 in.)
(B) 30 mm (1.18 in.) 6 mm (0.24 in.)


Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:
·

If a camshaft position sensor (for Exhaust Side and for Intake Side) has been struck or dropped, replace it.

·

Make sure that the 2 O-rings are not cracked or moved out of place when installing the 2 camshaft position sensors (for Exhaust Side and for Intake Side).

·

Do not start the engine for at least 2 hours after installation.



HINT:

After tightening all bolts, check the tightening torque of the bolts (7) and (8). Retighten them if necessary.



Hide 16305E 39.INSTALL OUTLET WATER BY-PASS SUB-ASSEMBLY

a.

Using an 8 mm socket wrench, install the outlet water by-pass sub-assembly and a new outlet water pipe gasket to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16304 40.INSTALL OUTLET WATER SUB-ASSEMBLY

a.

Using an 8 mm socket wrench, install the outlet water sub-assembly and a new outlet water gasket to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13470 41.INSTALL CRANKSHAFT PULLEY ASSEMBLY

a.
A433597C01
1,1.083 0.583,1.083 0.583,1.083 0.854,0.646 false 0.031,0.323 0.344,0.521 0.313,0.198 10 false *a 2.406,1.865 2.719,2.063 0.313,0.198 10 false *b 0.25,1.01 0.708,1.208 0.458,0.198 10 false SST
*a Hold
*b Turn


Align the crankshaft timing gear key with the key groove of the crankshaft pulley assembly.


b.

Using SST, hold the crankshaft pulley assembly and install the crankshaft pulley bolt.

SST
09213-54015  
09330-00021  

Torque:
260 N*m (2651 kgf*cm, 192 ft.*lbf)


Hide 12204C 42.INSTALL PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 12108A 44.INSTALL OIL FILLER CAP GASKET

a.
A366042

Install a new oil filler cap gasket to the oil filler cap sub-assembly.


Hide 12180E 45.INSTALL OIL FILLER CAP ASSEMBLY

a.

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.


Hide 16032 46.INSTALL ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

Hide 16031 47.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Hide 15370 48.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side)

Hide 15370 49.INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side)

Hide 89448D 50.INSTALL OIL PRESSURE AND TEMPERATURE SENSOR

Hide 19100P 52.INSTALL SPARK PLUG