Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › 2020.03–2020.07
RM36W0E _57 Power Source / Network _088060 NETWORKING _0424331 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Check Bus 3 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen.
·

CAN main bus line, CAN branch line or connector

·

Radio and display receiver assembly

·

Meter mirror sub-assembly

(w/ Headup Display)

·

Combination meter assembly

·

Central gateway ECU (network gateway ECU)

·

No. 4 global CAN junction connector



WIRING DIAGRAM

C430893E01
0.323,2.563 2.26,2.99 1.938,0.427 10 false Central Gateway ECU (Network Gateway ECU) 0.323,2.385 0.823,2.615 0.5,0.229 10 false H40 0.396,4.542 0.896,4.771 0.5,0.229 10 false H61 0.385,4.708 2.344,5.219 1.958,0.51 10 false Meter Mirror Sub-assembly*1 2.542,4.74 5.177,5.042 2.635,0.302 10 false No. 4 Global CAN Junction Connector 2.542,4.573 3.042,4.802 0.5,0.229 10 false H115 1.281,3.625 1.781,3.854 0.5,0.229 10 false MPX1 1.271,4.146 1.771,4.375 0.5,0.229 10 false MPX2 6,3.906 6.5,4.135 0.5,0.229 10 false 120 Ω 4.146,1.354 4.469,1.573 0.323,0.219 10 false 3 2.802,1.365 3.125,1.583 0.323,0.219 10 false 1 2.813,3.521 3.135,3.74 0.323,0.219 10 false 5 2.76,4.052 3.083,4.271 0.323,0.219 10 false 16 1.771,4.052 2.094,4.271 0.323,0.219 10 false 13 1.76,3.521 2.083,3.74 0.323,0.219 10 false 12 1.792,1.917 2.115,2.135 0.323,0.219 10 false 29 1.781,1.385 2.104,1.604 0.323,0.219 10 false 30 4.135,3.521 4.458,3.74 0.323,0.219 10 false 2 4.104,4.052 4.427,4.271 0.323,0.219 10 false 13 5.115,1.354 5.438,1.573 0.323,0.219 10 false 13 1.302,1.385 1.802,1.615 0.5,0.229 10 false CA3H 1.333,1.917 1.833,2.146 0.5,0.229 10 false CA3L 2.76,1.906 3.083,2.125 0.323,0.219 10 false 12 4.115,1.906 4.438,2.125 0.323,0.219 10 false 14 5.313,3.521 5.813,3.75 0.5,0.229 10 false CANH 5.323,4.052 5.823,4.281 0.5,0.229 10 false CANL 5.063,4.042 5.385,4.26 0.323,0.219 10 false 25 5.104,3.521 5.427,3.74 0.323,0.219 10 false 9 5.156,4.531 5.656,4.76 0.5,0.229 10 false H6 0.615,1.75 1.115,1.979 0.5,0.229 10 false 120 Ω 5.125,1.896 5.448,2.115 0.323,0.219 10 false 14 5.365,1.49 5.865,1.719 0.5,0.229 10 false CANH 5.375,2.031 5.875,2.26 0.5,0.229 10 false CANL 5.083,2.406 5.583,2.635 0.5,0.229 10 false H80 5.083,2.583 6.781,3.042 1.698,0.458 10 false Radio and Display Receiver Assembly 5.146,4.688 7.073,5 1.927,0.313 10 false Combination Meter Assembly 0.24,5.26 2.219,5.542 1.979,0.281 10 false *1: w/ Headup Display

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C425195C15
1.448,0.104 1.958,0.313 0.51,0.208 0.406,1.792 1.115,0.885 true 2.552,1.802 1.208,0.885 true 0.219,1.833 0.833,2.031 0.615,0.198 10 false CA3H 2.417,1.844 3.031,2.042 0.615,0.198 10 false CA3L 1.594,0.146 2.052,0.344 0.458,0.198 10 false H40 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-30 (CA3H) - H40-29 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES

NG

32.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES
a.
C425195C16
1.448,0.104 1.958,0.313 0.51,0.208 0.406,1.792 1.115,0.885 true 2.552,1.802 1.208,0.885 true 0.219,1.833 0.833,2.031 0.615,0.198 10 false CA3H 2.417,1.844 3.031,2.042 0.615,0.198 10 false CA3L 1.594,0.146 2.052,0.344 0.458,0.198 10 false H40 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-30 (CA3H) - H40-29 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Result
OK
NG



OK

3.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

23.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C05
1.917,0.25 2.417,0.5 0.5,0.25 5.281,0.25 5.781,0.5 0.5,0.25 1.042,2.156 1.563,1.292 true 1.677,1.292 2.781,2.177 true 6.292,1.604 6.469,1.958 true 3.938,0.25 4.25,0.448 0.313,0.198 10 false *1 2.031,0.281 2.427,0.479 0.396,0.198 10 false H40 2.854,2.156 3.406,2.354 0.552,0.198 10 false CA3L 6.521,1.854 7.073,2.052 0.552,0.198 10 false BAT 0.677,2.167 1.229,2.365 0.552,0.198 10 false CA3H 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 5.448,0.271 5.844,0.469 0.396,0.198 10 false H3
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H40-30 (CA3H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-29 (CA3L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

14.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
4.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C07
1.917,0.25 2.417,0.5 0.5,0.25 5.281,0.25 5.781,0.5 0.5,0.25 1.042,2.135 1.563,1.302 true 1.667,1.292 2.667,2.188 true 5.385,1.188 4.969,1.979 true 3.938,0.25 4.25,0.448 0.313,0.198 10 false *1 2.031,0.281 2.427,0.479 0.396,0.198 10 false H40 2.729,2.156 3.281,2.354 0.552,0.198 10 false CA3L 4.74,1.969 5.292,2.167 0.552,0.198 10 false CG 0.635,2.104 1.188,2.302 0.552,0.198 10 false CA3H 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 5.448,0.271 5.844,0.469 0.396,0.198 10 false H3
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
H40-30 (CA3H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-29 (CA3L) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-30 (CA3H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-29 (CA3L) - H3-4 (CG)



c.

Reconnect the central gateway ECU (network gateway ECU) connector.


Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-9 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H6-25 (CANL) - H3-4 (CG)



c.

Reconnect the combination meter assembly connector.


Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
7.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Combination meter assembly
H115-13 (CANL) - H3-4 (CG)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A77-6 (CANH) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher No. 4 global CAN junction connector
A77-17 (CANL) - H56-4 (CG)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

9.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

9.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

B

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
10.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-5 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Meter mirror sub-assembly
H115-16 (CANL) - H3-4 (CG)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Radio and display receiver assembly
H115-14 (CANL) - H3-4 (CG)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
12.CHECK FOR SHORT TO GND IN CAN BUS LINE (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H61 meter mirror sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-12 (MPX1) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H61-13 (MPX2) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-13 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H80-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

14.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-30 (CA3H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-29 (CA3L) - H3-16 (BAT)



c.

Reconnect the central gateway ECU (network gateway ECU) connector.


Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

15.CHECK FOR SHORT TO +B IN CAN BUS LINE (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
15.CHECK FOR SHORT TO +B IN CAN BUS LINE (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-9 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H6-25 (CANL) - H3-16 (BAT)



c.

Reconnect the combination meter assembly connector.


Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

16.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
16.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Combination meter assembly
H115-13 (CANL) - H3-16 (BAT)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

17.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

17.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
H115-12 (CANL) - H3-16 (BAT)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

18.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

18.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

19.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

B

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
19.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-5 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Meter mirror sub-assembly
H115-16 (CANL) - H3-16 (BAT)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

21.CHECK FOR SHORT TO +B IN CAN BUS LINE (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Radio and display receiverassembly
H115-14 (CANL) - H3-16 (BAT)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

22.CHECK FOR SHORT TO +B IN CAN BUS LINE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
21.CHECK FOR SHORT TO +B IN CAN BUS LINE (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H61 meter mirror sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-12 (MPX1) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H61-13 (MPX2) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

22.CHECK FOR SHORT TO +B IN CAN BUS LINE (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-13 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H80-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

23.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-30 (CA3H) - H40-29 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Reconnect the central gateway ECU (network gateway ECU) connector.


Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

24.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
24.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-9 (CANH) - H6-25 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Reconnect the combination meter assembly connector.


Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

25.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
25.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-2 (CANH) - H115-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Combination meter assembly



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

26.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

26.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-1 (CANH) - H115-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

27.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

27.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Headup Display A
w/o Headup Display B



A

28.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)

B

29.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
28.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - METER MIRROR SUB-ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-5 (CANH) - H115-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Meter mirror sub-assembly



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

29.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

30.CHECK FOR SHORT IN CAN BUS LINES (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
29.CHECK FOR SHORT IN CAN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-3 (CANH) - H115-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Radio and display receiver assembly



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

31.CHECK FOR SHORT IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
30.CHECK FOR SHORT IN CAN BUS LINES (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H61 meter mirror sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H61-12 (MPX1) - H61-13 (MPX2) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (METER MIRROR SUB-ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

31.CHECK FOR SHORT IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H80-13 (CANH) - H80-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)

32.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H40-30 (CA3H) - H40-29 (CA3L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Reconnect the central gateway ECU (network gateway ECU) connector.


Result:
Result
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

33.CHECK FOR OPEN IN CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
33.CHECK FOR OPEN IN CAN MAIN BUS LINES (COMBINATION METER ASSEMBLY - NO. 4 GLOBAL CAN JUNCTION CONNECTOR)
a.

Disconnect the H6 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-9 (CANH) - H6-25 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Reconnect the combination meter assembly connector.


Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

34.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
34.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-2 (CANH) - H115-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Combination meter assembly



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

35.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK ATEWAY ECU))

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

35.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK ATEWAY ECU))
a.

Disconnect the H115 No. 4 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
H115-1 (CANH) - H115-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)



c.

Reconnect the No. 4 global CAN junction connector.


Result:
Result
OK
NG



OK

REPLACE NO. 4 GLOBAL CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 4 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))