Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for M15A-FKS) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _088019 HEATING / AIR CONDITIONING _0424501 COMPRESSOR(for M15A-FKS) A

HEATING / AIR CONDITIONING  COMPRESSOR(for M15A-FKS)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT COMPRESSOR OIL

a.

Remove the suction seal cap.


b.
I110486C02
1.719,1.406 2.625,1.208 true 1.313,1.927 1.625,1.635 true 2.667,1.125 2.979,1.281 0.313,0.156 10 false *a 1.146,1.854 1.458,2.01 0.313,0.156 10 false *b
*a VST Valve (Valve Inside Suction Port)
*b Protective Tape


Using a screwdriver with its tip wrapped in protective tape, insert the screwdriver through the suction port and set the VST valve (valve inside suction port) to the open position.

NOTICE:

Be sure not to damage the piping contact surfaces with the tip of the screwdriver.



c.
I115590C02
1.281,1.75 1.583,1.604 true 1.104,1.708 1.302,1.865 0.198,0.156 10 false *a
*a Suction Port


Lightly shake the compressor with pulley assembly with the suction port facing down, and drain the oil (*1).

NOTICE:

Do not allow the pulley to come into contact with the compressor oil.



d.
I110439C02
2.125,1.448 2.625,1.167 false 2.688,1.063 3,1.219 0.313,0.156 10 false *1 1.906,1.813 2.219,1.969 0.313,0.156 10 false *a
*1 Pulley
*a Down


With the pulley facing down, rotate the pulley in the direction shown by the arrow 10 times at a rate of approximately once every 2 seconds (*2).

NOTICE:

If the pulley is rotated, refrigerant or oil might splash out. Thus, keep your face away from the compressor port.



e.
I110440C02
0.823,0.5 1.302,0.76 false 0.625,0.396 0.938,0.552 0.313,0.156 10 false *1 1.875,0.229 2.188,0.385 0.313,0.156 10 false *a
*1 Pulley
*a Up


Rotate the pulley once in the direction shown by the arrow while quickly turning the compressor so the pulley is up (*3).


f.

Proceed with the above procedure (*1) and drain the oil (*4).


g.

Drain the oil by repeating the procedures above approximately 5 times (from (*2) to (*4)).

Standard (Amount of Oil to be Removed):
Standard (Amount of Oil to be Removed) Amount of Oil Inside a New Compressor
30 cm3 60 cm3


HINT:

If too much oil has been removed, set the VST valve to the open position through the suction port, and add oil.



Hide 88310 2.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

a.
I115576N02
1.198,0.438 1.281,0.594 0.083,0.156 10 true 1 1.844,0.458 1.927,0.615 0.083,0.156 10 true 4 1.146,1.99 1.25,2.146 0.104,0.156 10 false 3 1.656,2.01 1.76,2.167 0.104,0.156 10 false 2

Temporarily install the compressor assembly with pulley with the 4 bolts.


b.

Tighten the 4 bolts and install the compressor assembly with pulley in the order shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Connect the connector.


Hide 88703 3.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the discharge hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the discharge hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the discharge hose sub-assembly to the compressor assembly with pulley with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 88704 4.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction hose sub-assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor assembly with pulley.

Compressor Oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction hose sub-assembly to the compressor assembly with pulley with the bolt.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 16361A 5.INSTALL FAN AND GENERATOR V BELT

Hide 51451A 6.INSTALL CENTER ENGINE UNDER COVER

Hide 7.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT