Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2020.03–2020.07
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0424523 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-collision system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 56111 1.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B106929

Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean it with a non-residue solvent.





Hide 56116C 2.INSTALL NO. 2 WINDSHIELD GLASS STOPPER

a.

Using a brush or sponge, coat the installation area of the 2 No. 2 windshield glass stoppers with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

B563181C02
1.938,0.625 2.208,0.385 false 4.833,0.646 5.01,0.354 true 6.198,0.448 6.396,0.24 false 0.531,0.521 0.802,0.281 true 1.26,0.625 1.531,0.385 true 5.583,0.583 5.76,0.292 true 2.021,1.927 2.333,2.083 0.313,0.156 10 false *a 2.271,0.313 2.583,0.469 0.313,0.156 10 false *c 0.729,1.396 0.885,1.552 0.156,0.156 10 false b 2.563,0.76 2.719,0.917 0.156,0.156 10 false a 0.854,0.219 1.167,0.375 0.313,0.156 10 false *b 5.229,1.448 5.385,1.604 0.156,0.156 10 false b 5.823,0.208 6.135,0.365 0.313,0.156 10 false *b 6.906,0.438 7.063,0.594 0.156,0.156 10 false a 6.448,0.177 6.76,0.333 0.313,0.156 10 false *c 5.094,0.26 5.406,0.417 0.313,0.156 10 false *b 1.583,0.313 1.896,0.469 0.313,0.156 10 false *b
*a Back Side of Windshield Glass *b Ceramic Notch
*c Windshield Glass Edge Side - -


Standard Dimension:
Area Dimension
a 14.4 to 15.4 mm (0.567 to 0.606 in.)
b 40 mm (1.57 in.)


HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56115A 3.INSTALL NO. 1 WINDSHIELD GLASS STOPPER

a.
B563182

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56117A 4.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the installation area of the window glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B563183C02
0.677,2.906 0.781,2.698 true 2.115,3.094 2.229,2.854 true 0.219,0.073 0.531,0.229 0.313,0.156 10 false *a 0.583,2.938 0.802,3.104 0.219,0.167 10 true *b 2.01,3.125 2.229,3.292 0.219,0.167 10 true *b
*a Back Side of Windshield Glass
*b Ceramic Notch


Install a new window glass adhesive dam to the windshield glass as shown in the illustration.


Hide 75533G 5.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the installation area of the windshield outside moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install a new windshield outside moulding to the windshield glass as shown in the illustration.

B563184C02
1.125,3.021 0.979,3.167 false 3,3 3.177,3.167 false 0.521,0.396 0.833,0.552 0.313,0.156 10 false *a 1.188,2.938 1.5,3.094 0.313,0.156 10 false *b 2.823,2.906 3.135,3.063 0.313,0.156 10 false *b 2.375,0.396 2.521,0.552 0.146,0.156 10 false A 2.385,0.802 2.531,0.958 0.146,0.156 10 true A 4.469,1.083 4.813,1.24 0.344,0.156 10 false A-A 5.771,1.146 5.917,1.302 0.146,0.156 10 false a
*a Back Side of Windshield Glass *b Ceramic Notch


Standard Dimension:
Area Dimension
a 1.15 to 2.65 mm (0.0453 to 0.104 in.)



Hide 56111 6.INSTALL WINDSHIELD GLASS

a.

Clean and shape the contact surface of the vehicle body.

i.
B153152C18
0,0 0,0 false
V100155

Adhesive


Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.



b.

Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the whole contact surface of the windshield glass rim is perfectly even.


iii.
B563185C03
1.271,1.729 1.75,1.594 1.75,1.594 1.406,1.531 true 1.833,1.479 2.042,1.667 0.208,0.188 10 true *a
*a Matchmark


Align the matchmarks on the windshield glass and vehicle body.

NOTICE:

Check that the windshield glass stoppers are engaged to the vehicle body correctly.



iv.

Remove the windshield glass.



c.

Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



d.

Using a brush or sponge, coat the adhesive application area with primer G.

B563186C02
6.063,4.146 6.323,4 false 6.385,3.906 6.698,4.063 0.313,0.156 10 false *1 5.698,0.094 5.854,0.25 0.156,0.156 10 false a 0.667,0.802 0.979,0.958 0.313,0.156 10 false *a 4.594,0.25 4.917,0.417 0.323,0.167 10 false A-A 1.688,1.344 1.844,1.5 0.156,0.156 10 false B 1.656,1.708 1.813,1.865 0.156,0.156 10 true B 0.917,1.635 1.073,1.792 0.156,0.156 10 true A 0.979,1.271 1.135,1.427 0.156,0.156 10 false A 0.625,1.802 0.781,1.958 0.156,0.156 10 false C 0.948,1.865 1.104,2.021 0.156,0.156 10 true C 0.667,2.74 0.781,2.906 0.115,0.167 10 true D 0.542,3.094 0.698,3.25 0.156,0.156 10 false D 4.573,1.26 4.896,1.427 0.323,0.167 10 false B-B 4.583,2.427 4.906,2.594 0.323,0.167 10 false C-C 4.594,3.74 4.917,3.906 0.323,0.167 10 false D-D 5.708,1.104 5.865,1.26 0.156,0.156 10 false b 5.698,2.292 5.854,2.448 0.156,0.156 10 false c 5.708,3.625 5.865,3.781 0.156,0.156 10 false d
*1 Window Glass Adhesive Dam - -
*a Back Side of Windshield Glass - -
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 11 mm (0.433 in.) or more
b 11 mm (0.433 in.) or more
c 11 mm (0.433 in.) or more
d 19 mm (0.748 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply primer G to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




e.

Apply adhesive to the windshield glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Cartridge Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12 to 15 mm (0.472 to 0.591 in.)
b 8.0 to 11 mm (0.315 to 0.433 in.)




f.

Load the sealer gun with the cartridge.


g.

Apply adhesive to the windshield glass as shown in the illustration.

B563187C02
5.865,4.135 6.125,4 false 6.188,3.938 6.5,4.094 0.313,0.156 10 false *1 4.573,0.292 4.99,0.438 0.417,0.146 10 false A-A 0.531,0.875 0.844,1.031 0.313,0.156 10 false *a 0.615,1.792 0.771,1.948 0.156,0.156 10 false C 0.542,3.083 0.698,3.24 0.156,0.156 10 false D 0.646,2.74 0.75,2.896 0.104,0.156 10 true D 0.948,1.865 1.104,2.021 0.156,0.156 10 true C 0.938,1.635 1.073,1.802 0.135,0.167 10 true A 0.979,1.281 1.115,1.448 0.135,0.167 10 false A 1.667,1.698 1.802,1.865 0.135,0.167 10 true B 1.688,1.344 1.823,1.51 0.135,0.167 10 false B 5.583,0.104 5.74,0.281 0.156,0.177 10 false a 5.583,1.125 5.74,1.302 0.156,0.177 10 false b 5.51,2.302 5.667,2.479 0.156,0.177 10 false c 5.583,3.552 5.74,3.729 0.156,0.177 10 false d 4.594,1.302 5.01,1.448 0.417,0.146 10 false B-B 4.573,2.427 4.99,2.573 0.417,0.146 10 false C-C 4.573,3.688 4.99,3.833 0.417,0.146 10 false D-D
*1 Window Glass Adhesive Dam - -
*a Back Side of Windshield Glass - -
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 8.0 to 11 mm (0.315 to 0.433 in.)
b 8.0 to 11 mm (0.315 to 0.433 in.)
c 8.0 to 11 mm (0.315 to 0.433 in.)
d 8.0 mm (0.315 in.)



h.

Install the windshield glass.

i.
B563185C04
1.25,1.75 1.646,1.563 1.646,1.563 1.396,1.531 true 1.708,1.49 1.917,1.667 0.208,0.177 10 true *a
*a Matchmark


Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass.




ii.

Lightly press the outer surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the windshield glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




Hide 7.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63311C 8.INSTALL ROOF HEADLINING

a.

Return the front section of the roof headlining to its original position.


Hide 74612 9.INSTALL ASSIST GRIP COVER

Hide 74610A 10.INSTALL ASSIST GRIP SUB-ASSEMBLY

Hide 74310 12.INSTALL VISOR ASSEMBLY RH

Hide 74320 13.INSTALL VISOR ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 81260A 14.INSTALL MAP LIGHT ASSEMBLY

Hide 62212 16.INSTALL FRONT PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62311B 17.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.

Install the front door opening trim weatherstrip RH.


Hide 62312B 18.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Use the same procedure as for the RH side.


Hide 87810 19.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 86401 20.INSTALL FORWARD RECOGNITION WITH HEATER HOOD SUB-ASSEMBLY

Hide 8646C 21.INSTALL FORWARD RECOGNITION CAMERA

Hide 22.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 8646C 23.ADJUST FORWARD RECOGNITION CAMERA

a.

If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform Forward Recognition Camera Learning.

HINT:

Forward Recognition Camera Learning can be performed by using either Target Adjustment (One Time Recognition) or Target Adjustment (Sequential Recognition) or Driving Adjustment.