Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087837 M15A-FKS ENGINE MECHANICAL _0424630 ENGINE UNIT A

M15A-FKS ENGINE MECHANICAL  ENGINE UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Cam timing control motor with EDU assembly

·

Removal and installation of a cam timing control motor with EDU assembly

·

Camshaft timing gear assembly

·

Removal and installation of a camshaft timing gear assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Port fuel injector assembly

·

Direct fuel injector assembly

·

Fuel pump (for low pressure side)

·

Fuel pump assembly (for high pressure side)

·

Fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side)

·

Fuel pressure sensor (for high pressure side)

·

Air fuel ratio sensor (sensor 1)

·

Air fuel ratio sensor (sensor 2)

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

EGR valve assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 17167 2.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 22030 5.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 22271 6.REMOVE THROTTLE BODY GASKET

Hide 23820 7.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY

a.
A458210

Disconnect the fuel vapor hose assembly to the purge valve.


b.

Disengage the clamp to remove the fuel vapor feed hose assembly from the intake manifold.


Hide 12262 8.REMOVE NO. 2 VENTILATION HOSE

a.
A458211

Slide the hose clip and remove the No. 2 ventilation hose from the cylinder head cover sub-assembly.


Hide 25680 9.REMOVE EGR VALVE WITH EGR CCOLER ASSEMBLY

Hide 25601 10.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 25624 11.REMOVE EGR VALVE ADAPTER

a.
A466630

Using an 8 mm socket wrench, remove the bolt and EGR valve adapter from the camshaft housing sub-assembly.


Hide 17177 13.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 23901 14.REMOVE FUEL TUBE SUB-ASSEMBLY

a.
A458212

Remove the fuel tube sub-assembly from the No. 2 fuel pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23902 15.REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY

a.
A458213

Remove the fuel pipe clamp from the fuel tube connector.


b.
A458214

Remove the fuel tube sub-assembly from the No. 2 fuel pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PARTS LOCATION


Hide 23802B 16.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

a.
A458215

Remove the 2 bolts and No. 2 fuel pipe sub-assembly from the camshaft housing subassembly.


Hide 23100X 17.REMOVE FUEL PUMP ASSEMBLY (for High Pressure)

Hide 18.REMOVE WATER BY-PASS PIPE ASSEMBLY

a.
A458217

Remove the bolt.


b.

Slide the clip and remove the water by-pass hose assembly from the water inlet with thermostat sub-assembly.


Hide 82219C 19.REMOVE SENSOR WIRE

a.
A458218

Disconnect the 4 connectors.


b.

Disengage the 2 clamps.


c.

Remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.


Hide 82126A 20.REMOVE NO. 6 ENGINE WIRE

a.
A458219

Disconnect the 3 connectors.


b.

Disengage the clamp and remove the No. 6 engine wire from the No. 1 ventilation case.


Hide 23250 21.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11452D 23.REMOVE OIL LEVEL GAGE GUIDE

a.

Remove the engine oil level dipstick.


b.
A458220

Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the cylinder head sub-assembly.


c.
A458221

Remove the O-ring from the engine oil level dipstick guide.


Hide 16281 24.REMOVE NO. 4 WATER BY-PASS HOSE

a.
A458222

Disengage the clamp to separate the No. 4 water by-pass hose.


b.

Slide the clip and remove the No. 4 water by-pass hose from the water outlet.


Hide 25.REMOVE WIRE HARNESS CLAMP BRACKET

a.
A458223

Using an 8 mm socket wrench, remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly.


b.
A458224

Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the camshaft housing sub-assembly.


c.
A458225

Remove the 2 bolts and wire harness clamp bracket from the camshaft housing sub-assembly.