The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Perform "Inspection After Repair" after replacing the engine assembly.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
1.INSTALL ENGINE HANGER
2.REMOVE ENGINE FROM ENGINE STAND
Remove the engine assembly from the engine stand.
88310
3.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY
27020
4.INSTALL GENERATOR ASSEMBLY
for 80A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 80A Type)>INSTALLATION
for 100A Type:
Click herePower Source / Network>M15A-FKS (BATTERY / CHARGING)>GENERATOR (for 100A Type)>INSTALLATION
16620D
5.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
Install the V-ribbed belt tensioner assembly with the 2 bolts.
16361A
6.INSTALL FAN AND GENERATOR V BELT
19315
7.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
13405
8.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)
31210
9.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)
32101B
10.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)
11.INSTALL ENGINE ASSEMBLY (for Manual Transaxle)
12.INSTALL ENGINE ASSEMBLY (for CVT)
82121
13.INSTALL ENGINE WIRE
Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.
Install the 6 bolts.
| *A | for CVT |
| *B | for Manual Transaxle |
for CVT:
Install the 3 bolts.
for Manual Transaxle:
Install the 4 bolts.
| *A | for CVT |
| *B | for Manual Transaxle |
Install the 2 bolts.
11363A
14.INSTALL FLYWHEEL HOUSING SIDE COVER
Install the flywheel housing side cover to the cylinder block sub-assembly.
28100
15.INSTALL STARTER ASSEMBLY
16.INSTALL WATER HOSE (for CVT)
Install the water hose to the engine assembly with transaxle and slide the 3 clips to secure it.
Engage the clamp to the engine assembly with transaxle.
17.INSTALL WATER HOSE (for Manual Transaxle)
Install the water hose to the engine assembly with transaxle and slide the 3 clips to secure it.
Engage the clamp to the engine assembly with transaxle.
12305
18.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH
Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.
| *a | Temporarily Tighten |
Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.
Install the 2 bolts and nut in the order shown in the illustration.
Connect the air conditioner tube with the clamp.
12372A
19.INSTALL ENGINE MOUNTING INSULATOR LH
Perform this procedure only when replacement of the engine mounting insulator LH is necessary.
| *a | Temporarily Tighten |
Temporarily install the engine mounting insulator LH to the vehicle.
Install the 5. bolts and nut in the order shown in the illustration.
20.REMOVE ENGINE HANGER
12353
21.INSTALL ENGINE MOUNTING BRACKET CAP
Install the engine mounting bracket cap to the engine mounting bracket RH.
22.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.
Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.
Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.
To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.
Operate the engine lifter and install the engine assembly with transaxle to the vehicle.
Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.
Make sure that the engine assembly with transaxle is clear of all wiring and hoses.
While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.
Connect the front suspension crossmember sub-assembly to the vehicle with the 10 bolts.
for CVT:
Install the engine mounting insulator LH to the engine mounting bracket LH with the 3 bolts and nut in the order shown illustration.
for Manual Transaxle:
Install the engine mounting insulator LH to the engine mounting bracket LH with the 4 bolts and nut in the order shown illustration.
Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut in the order shown illustration.
32101G
23.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for CVT)
11361J
24.INSTALL FLYWHEEL HOUSING UNDER COVER (for CVT)
31481A
25.INSTALL NO. 1 CLUTCH HOSE (for Manual Transaxle)
| *a | 10 mm Union Nut Wrench |
| *b | Torque Wrench Fulcrum Length |
Connect the No. 1 clutch hose to the clutch flexible hose bracket with a new clip.
Using a 10 mm union nut wrench, connect the bleeder clutch release tube to the No. 1 clutch hose.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)
26.INSTALL DRIVE SHAFT ASSEMBLY
17410
27.INSTALL FRONT EXHAUST PIPE ASSEMBLY
45260
28.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
29.INSTALL COLUMN HOLE COVER SILENCER SHEET
88704
30.CONNECT SUCTION HOSE SUB-ASSEMBLY
88703
31.CONNECT DISCHARGE HOSE SUB-ASSEMBLY
23901
32.CONNECT FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the fuel pump assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the No. 1 fuel pipe clamp to the fuel tube sub-assembly.
87245
33.CONNECT INLET HEATER WATER HOSE
16290F
34.CONNECT NO.3 WATER BY-PASS HOSE ASSEMBLY
77261D
35.CONNECT FUEL TANK TO CANISTER TUBE
Engage the clamp to connect the fuel tank to canister tube to the engine wire.
23826
36.CONNECT NO. 1 FUEL VAPOR FEED HOSE
Connect the No. 1 fuel vapor feed hose to the fuel tank to canister tube.
44777
37.CONNECT NO. 1 VACUUM HOSE CONNECTOR
33820B
38.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)
33820B
39.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
| *a | Paint Mark |
Install the transmission control cable assembly to the control cable bracket assembly with 2 new clips (B).
Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.
Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips (A).
16572D
40.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.
16571C
41.CONNECT NO. 1 RADIATOR HOSE
Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.
42.CONNECT ENGINE WIRE
Disconnect the 3 connectors from the engine room relay block.
Disengage the 2 claws to separate the engine wire from the engine room relay block.
Install the No. 1 relay block cover to the engine room relay block.
Engage the 2 clamps to connect the engine wire to the vehicle.
Connect the engine wire to the positive (+) auxiliary battery terminal with the 2 nuts.
Connect the engine wire to the vehicle with the 2 bolts.
74404A
43.INSTALL BATTERY CLAMP SUB-ASSEMBLY
Install the battery clamp sub-assembly to the vehicle with the 3 bolts.
89661
44.INSTALL ECM
17701
45.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly to the vehicle.
Engage the clamp to the air cleaner case sub-assembly.
Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.
46.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
| *1 | Air cleaner cap sub-assembly clamp |
| *2 | Guide |
| *a | Top of Vehicle |
| *b | Front of Vehicle |
| *c | Stopper |
Connect the air cleaner cap with air cleaner hose and tighten the hose clamp.
Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.
Engage the 2 air cleaner cap sub-assembly clamps to install the air cleaner cap sub-assembly.
Engage the clamp to the air cleaner cap sub-assembly.
Connect the mass air flow meter connector.
55701J
47.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
55815E
48.INSTALL NO. 1 FRONT VENTILATOR SEAL
55735A
49.INSTALL WATER GUARD PLATE LH
50.INSTALL WINDSHIELD WIPER MOTOR AND LINK
51.INSTALL AUXILIARY BATTERY
52.ADD ENGINE OIL
53.ADD ENGINE COOLANT
54.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)
55.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)
56.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
57. WARM UP ENGINE
58.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)
59.INSPECT SHIFT LEVER POSITION (for CVT)
60.ADJUST SHIFT LEVER POSITION (for CVT)
61.INSPECT FOR ENGINE OIL LEAK
62.INSPECT FOR COOLANT LEAK
63.INSPECT MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)
64.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK (for CVT)
65.INSPECT FOR REFRIGERANT LEAK
66.INSPECT FOR FUEL LEAK
67.INSPECT FOR EXHAUST GAS LEAK
68.CHECK ENGINE OIL LEVEL
69.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK
51447D
70.INSTALL CENTER NO. 4 ENGINE UNDER COVER
51441C
71.INSTALL ENGINE UNDER COVER RH
51442C
72.INSTALL ENGINE UNDER COVER LH
51451A
73.INSTALL CENTER ENGINE UNDER COVER
74.INSTALL FRONT WHEELS
75. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
76.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
77.PERFORM INITIALIZATION
78.INSPECT IGNITION TIMING
79.INSPECT ENGINE IDLE SPEED
80.INSPECT CO/HC
81.CHECK SPEED SENSOR SIGNAL