The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the parking brake cable assembly removal/installation are shown below.
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
Immediately after installing the brake shoes, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the brake shoes, the brake pedal may feel soft due to clearance between the rear brake shoe and brake drum. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the brake shoes, always perform a road test to check the braking performance and check for vibrations.
When removing or installing the brake shoes or pushing back the wheel brake cylinder piston may cause a large clearance between the brake shoes and brake drum. When the brake pedal is depressed with a large clearance between the brake shoes and the brake drum, DTC C13DC00, C13DE00, C140000 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model)
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model)
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
1. PRECAUTION (for HV Model)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
58911A
2.REMOVE NO. 1 BOX SIDE PANEL
58912C
3.REMOVE NO. 2 BOX SIDE PANEL
58903A
4.REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY
58857A
5.REMOVE UPPER NO. 1 CONSOLE SUPPORT BRACKET
46410
6.LOOSEN NO. 1 PARKING BRAKE CABLE ASSEMBLY
| *1 | No. 1 Wire Adjusting Nut |
Loosen the equalizer and lock nut.
If the lock nut has been removed from the rod, replace the No. 1 wire adjusting nut with a new one.
7.SEPARATE PARKING BRAKE CABLE ASSEMBLY
04495
8.REMOVE REAR BRAKE SHOE KIT
17410
9.REMOVE FRONT EXHAUST PIPE ASSEMBLY
for M15A-FXE:
Click hereEngine / Hybrid System>M15A-FXE (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL
for M15A-FKS:
Click hereEngine / Hybrid System>M15A-FKS (INTAKE / EXHAUST)>EXHAUST MANIFOLD>REMOVAL
58153
10.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR
77606
11.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
46430
12.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Gasoline Model)
Remove the 4 bolts, nut and No. 3 parking brake cable assembly.
46430
13.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for HV Model)
Remove the 4 bolts, nut and No. 3 parking brake cable assembly.
46420
14.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for Gasoline Model)
Remove the 5 bolts, nut and No. 3 parking brake cable assembly.
46420
15.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for HV Model)
Remove the 5 bolts, nut and No. 3 parking brake cable assembly.