Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, Gasoline Model) › 2020.03–2020.07
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424994 ENTRY AND START SYSTEM(for Start Function, Gasoline Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, Gasoline Model)  Engine does not Start  


DESCRIPTION

for Manual Transaxle

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the clutch pedal is depressed, the engine can be started by pressing the engine switch.


for CVT

When the electrical key transmitter sub-assembly is in the cabin and the engine switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the engine can be started by pressing the engine switch.


Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Engine does not start
Power Source Control
·

Stop Light Switch*

·

Shift P Signal*

·

Neutral SW/ Clutch SW

·

Starter Relay Driving Request (Starting Control)

·

Shift P/N (Starting Control)


Entry&Start
·

Immobiliser

·

Start Request

·

L Code Check



*: for CVT


WIRING DIAGRAM

E443678E04
5.042,2.688 5.5,2.885 0.458,0.198 10 false STA 5.021,1.063 5.479,1.26 0.458,0.198 10 false STAR 5.031,1.74 5.49,1.938 0.458,0.198 10 false STP1 5.75,3.635 6.208,3.833 0.458,0.198 10 false P 6,3.438 6.458,3.635 0.458,0.198 10 false 14 4.74,1.635 5.198,1.833 0.458,0.198 10 false 21 4.729,0.948 5.188,1.146 0.458,0.198 10 false 10 4.76,2.615 5.219,2.813 0.458,0.198 10 false 3 5.656,1.063 6.115,1.26 0.458,0.198 10 false IC 5.667,1.958 6.125,2.156 0.458,0.198 10 false IC 5.656,2.906 6.115,3.104 0.458,0.198 10 false IC 5.083,0.74 5.542,0.938 0.458,0.198 10 false +B 0.531,2.802 0.99,3 0.458,0.198 10 false STA 0.479,1.146 0.938,1.344 0.458,0.198 10 false NSW 0.552,1.729 1.01,1.927 0.458,0.198 10 false STP 0.302,3.542 0.896,3.813 0.594,0.271 10 false ECM 6.594,3.646 7.052,3.844 0.458,0.198 10 false P2 4.573,5.24 5.031,5.438 0.458,0.198 10 false STP 5.656,6.635 6.115,6.833 0.458,0.198 10 false STP 2.604,4 3.063,4.198 0.458,0.198 10 false B 3.01,4 3.469,4.198 0.458,0.198 10 false L 2.198,4.26 2.656,4.458 0.458,0.198 10 false P 2.188,4.542 2.646,4.74 0.458,0.198 10 false N 1.76,4.958 3.552,5.302 1.792,0.344 10 false Park/Neutral Position Switch 1.448,6.5 2.615,6.823 1.167,0.323 10 false ST NO. 1 0.344,6.094 0.958,6.271 0.615,0.177 10 false ST NO. 1 1.208,7.896 2.698,8.135 1.49,0.24 10 false Starter Assembly 1.052,7.24 1.51,7.438 0.458,0.198 10 false B 2.219,7.417 2.677,7.615 0.458,0.198 10 false ST 6.031,4.75 7.156,5.177 1.125,0.427 10 false Shift Lock Control Unit Assembly 4.469,4.125 6.021,4.594 1.552,0.469 10 false Certification ECU (Smart Key ECU Assembly) 4.813,9.042 6.938,9.354 2.125,0.313 10 false Stop Light Switch Assembly 5.604,8.344 6.063,8.542 0.458,0.198 10 false IC 5.646,7.646 7.125,7.927 1.479,0.281 10 false from Auxiliary Battery 4.615,7.802 5.302,8.01 0.688,0.208 10 false STOP 5.198,8.167 5.656,8.365 0.458,0.198 10 false B 5.208,8.458 6.01,8.667 0.802,0.208 10 false L 6.115,8.667 6.573,8.865 0.458,0.198 10 false GND 4.688,1.156 5.146,1.354 0.458,0.198 10 false H45 5.969,3.635 6.438,3.833 0.469,0.198 10 false H46 0.948,1.031 1.469,1.354 0.521,0.323 10 false 23 0.938,2.677 1.979,2.958 1.042,0.281 10 false 30 0.948,1.719 1.604,1.917 0.656,0.198 10 false 21 0.281,2.01 0.74,2.208 0.458,0.198 10 false IC 2.729,3.75 3.188,3.948 0.458,0.198 10 false 4 1.76,4.781 2.219,4.979 0.458,0.198 10 false D45 4.823,8.875 5.281,9.073 0.458,0.198 10 false A63 1.354,6.115 1.813,6.313 0.458,0.198 10 false 1 2.031,6.104 2.49,6.302 0.458,0.198 10 false 2 2.021,5.844 2.479,6.042 0.458,0.198 10 false 3 1.354,5.854 1.896,6.073 0.542,0.219 10 false 5 0.76,7.042 1.219,7.24 0.458,0.198 10 false 1 0.677,7.25 1.135,7.448 0.458,0.198 10 false D80 2.51,7.448 2.969,7.646 0.458,0.198 10 false D54 4.99,8.458 5.448,8.656 0.458,0.198 10 false 3 4.99,8.083 5.448,8.281 0.458,0.198 10 false 7 6.552,8.573 7.01,8.771 0.458,0.198 10 false 2 2.615,7.229 3.073,7.427 0.458,0.198 10 false 1 6.406,3.531 6.865,3.729 0.458,0.198 10 false 3 6.031,4.583 6.49,4.781 0.458,0.198 10 false H20 4.323,5.146 4.781,5.344 0.458,0.198 10 false 35 4.281,5.885 7.083,6.156 2.802,0.271 10 false Skid Control ECU (Brake Actuator Assembly) 4.292,5.729 4.75,5.927 0.458,0.198 10 false A36 5.156,7.042 5.656,7.333 0.5,0.292 10 false D71 5.167,7.219 6.906,7.458 1.74,0.24 10 false Transmission Control ECU 5.375,6.521 5.74,6.74 0.365,0.219 10 false 43 3.313,4.427 3.771,4.625 0.458,0.198 10 false 5 4.688,1.844 5.146,2.042 0.458,0.198 10 false H45 4.688,2.792 5.146,2.99 0.458,0.198 10 false H45 0.333,3.375 1.573,3.594 1.24,0.219 10 false A54 0.667,5.438 2.146,5.719 1.479,0.281 10 false from Auxiliary Battery 0.104,0.052 2.208,0.323 2.104,0.271 12 false for CVT:

E443679E02
0.583,1.375 1.042,1.573 0.458,0.198 10 false NSW 0.635,2.188 1.094,2.385 0.458,0.198 10 false STA 0.417,2.75 0.875,2.948 0.458,0.198 10 false A54 0.396,2.917 0.854,3.115 0.458,0.198 10 false ECM 1.042,1.271 1.5,1.469 0.458,0.198 10 false 23 1.031,2.073 1.49,2.271 0.458,0.198 10 false 30 5.865,1.167 6.323,1.365 0.458,0.198 10 false 10 5.823,1.365 6.281,1.563 0.458,0.198 10 false H45 5.833,2.177 6.292,2.375 0.458,0.198 10 false H45 5.896,1.969 6.354,2.167 0.458,0.198 10 false 3 5.823,2.948 6.281,3.146 0.458,0.198 10 false H46 5.865,2.75 6.323,2.948 0.458,0.198 10 false 14 4.99,2.948 5.448,3.146 0.458,0.198 10 false P2 5.26,2.844 5.719,3.042 0.458,0.198 10 false 3 6.208,2.948 6.667,3.146 0.458,0.198 10 false P 6.177,2.083 6.635,2.281 0.458,0.198 10 false STA 6.156,1.271 6.615,1.469 0.458,0.198 10 false STAR 6.219,0.948 6.677,1.146 0.458,0.198 10 false +B 6.792,1.25 7,1.49 0.208,0.24 10 false IC 6.792,2.313 7,2.552 0.208,0.24 10 false IC 2.219,4.115 2.677,4.313 0.458,0.198 10 false A64 2.198,4.271 4.26,4.552 2.063,0.281 10 false Clutch Start Switch Assembly 2.552,3.823 3.01,4.021 0.458,0.198 10 false 2 3.552,3.823 4.01,4.021 0.458,0.198 10 false 1 3.354,3.844 3.813,4.042 0.458,0.198 10 false L 2.75,3.844 3.208,4.042 0.458,0.198 10 false B 4.385,4.094 5.521,4.698 1.135,0.604 10 false Shift Lock Control Unit Assembly 4.385,3.927 4.844,4.125 0.458,0.198 10 false H20 5.604,3.521 7.146,4.031 1.542,0.51 10 false Certification ECU (Smart Key ECU Assembly) 1.5,5.646 2.344,6 0.844,0.354 10 false ST NO. 1 2.094,5.25 2.354,5.427 0.26,0.177 10 false 2 2.094,5 2.354,5.177 0.26,0.177 10 false 3 1.396,5.25 1.656,5.427 0.26,0.177 10 false 1 1.406,4.99 1.667,5.167 0.26,0.177 10 false 5 0.417,5.24 1.135,5.479 0.719,0.24 10 false ST NO. 1 0.74,6.396 1.094,6.594 0.354,0.198 10 false D80 2.583,6.583 2.938,6.781 0.354,0.198 10 false D54 2.281,6.573 2.635,6.771 0.354,0.198 10 false ST 1.115,6.385 1.469,6.583 0.354,0.198 10 false B 0.813,6.188 1.167,6.385 0.354,0.198 10 false 1 2.656,6.385 3.01,6.583 0.354,0.198 10 false 1 1.271,7.031 2.604,7.302 1.333,0.271 10 false Starter Assembly 0.719,4.573 2.229,4.813 1.51,0.24 10 false from Auxiliary Battery 0.115,0.083 2.073,0.354 1.958,0.271 12 false for Manual Transaxle:

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or an electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



PROCEDURE

1.CHECK ENGINE SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.*1


c.

With the brake pedal released, check that pressing the engine switch causes the power source mode to change.*1


d.

With the clutch pedal released, check that pressing the engine switch causes the power source mode to change.*2


*1: for CVT

*2: for Manual Transaxle


Result:
Result Proceed to
Power source mode changes : Off → ACC → ON → off
(for CVT)
A
Power source mode changes : Off → ACC → ON → off
(for Manual Transaxle)
B
Power source mode does not change to ACC or ON C
Power source mode changes to ON but not to ACC D
Power source mode changes to ACC but not to ON E



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

B

4.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT P/N (STARTING CONTROL))

C

D

E

2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch
50003 454 206
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

26.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND GROUND)
3.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Move the shift lever to P.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The engine cannot be started when this item is OFF.


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 454 205
OK:

ON is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT P/N (STARTING CONTROL))

NG

23.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
4.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW, SHIFT P/N (STARTING CONTROL))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch
for Manual Transaxle

State of clutch pedal


for CVT

Shift position (P and N)


OFF or ON
for Manual Transaxle

OFF: Clutch pedal released

ON: Clutch pedal depressed


for CVT

OFF: Shift lever in any position other than P or N

ON: Shift lever in P or N


for Manual Transaxle
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


for CVT
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P/N (Starting Control)
for CVT

Park/Neutral position switch status


OFF or ON OFF: Shift lever not in P or N
ON: Shift lever in P or N
When OFF is displayed, the engine will not crank.
Body Electrical > Power Source Control > Data List
Tester Display
Shift P/N (Starting Control)
50003 454 703
OK:

The GTS display changes correctly in response to the shift lever or clutch pedal operation.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (POWER SUPPLY CONDITION)

NG

16.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
5.READ VALUE USING GTS (POWER SUPPLY CONDITION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state OFF, ACC ON, IGR ON, IGP ON or Starter ON OFF: Ignition switch off
ACC ON: Ignition switch ACC
IGR ON: Ignition switch ON
IGP ON: Ignition switch ON
Starter ON: Sending engine start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 454 405
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the engine switch.


OK:

The GTS display changes correctly in response to the engine switch operation.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (STARTER RELAY DRIVING REQUEST (STARTING CONTROL))

NG

14.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
6.READ VALUE USING GTS (STARTER RELAY DRIVING REQUEST (STARTING CONTROL))
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.*1


c.

According to the display on the GTS, read the Data List while pressing the engine switch with the brake pedal depressed.*1


d.

According to the display on the GTS, read the Data List while pressing the engine switch with the clutch pedal depressed.*2

*1: for CVT

*2: for Manual Transaxle


Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Relay Driving Request (Starting Control) Engine start request signal status OFF or ON
for Manual Transaxle

OFF: The engine switch is not pressed

ON: With the clutch pedal depressed, the engine switch is pressed and held


for CVT

OFF: The engine switch is not pressed

ON: With the shift lever in P and the brake pedal depressed, the engine switch is pressed and held


·

When the engine cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the engine switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the engine switch needs to be pressed and held for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Relay Driving Request (Starting Control)
50003 454 701
OK:

The GTS display changes.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST NO. 1 RELAY)
a.
C378519C11
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 1 Engine Room Relay Block Assembly
(ST NO. 1 Relay Holder)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 - Body ground
for Manual Transaxle

Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)


for CVT

Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)


6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Result Proceed to
OK A
NG (for CVT) B
NG (for Manual Transaxle) C



A

8.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - AUXILIARY BATTERY AND GROUND)

B

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST NO. 1 RELAY)

C

13.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)
8.CHECK HARNESS AND CONNECTOR (ST NO. 1 RELAY - AUXILIARY BATTERY AND GROUND)
a.
C378519C11
0.156,0.125 0.521,0.469 0.365,0.344 10 false *1
*1 No. 1 Engine Room Relay Block Assembly
(ST NO. 1 Relay Holder)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 1 - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 5 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.INSPECT ST NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT ST NO. 1 RELAY

OK

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)

NG

REPLACE ST NO. 1 RELAY

10.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the D54 starter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
No. 1 engine room relay block assembly ST NO. 1 relay terminal 3 - D54-1 Always Below 1 Ω
No. 1 engine room relay block assembly ST NO. 1 relay terminal 3 or D54-1 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (STARTER ASSEMBLY - AUXILIARY BATTERY)
a.

Disconnect the D80 starter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D80-1 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST NO. 1 RELAY)
a.

Disconnect the D45 park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D45-5 (L) - No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 Always Below 1 Ω
D45-5 (L) or No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)
a.

Disconnect the A64 clutch start switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-1 (L) - No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 Always Below 1 Ω
A64-1 (L) or No. 1 engine room relay block assembly ST NO. 1 relay terminal 2 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

14.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.*1


c.

Press the engine switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC. *1


d.

Press the engine switch with the clutch pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC. *2

*1: for CVT

*2: for Manual Transaxle


OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.



Result:
Proceed to
OK
NG



OK

15.CHECK STEERING LOCK FUNCTION

NG

15.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the ignition switch is turned to ACC.

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

16.READ VALUE USING GTS (NEUTRAL SW/ CLUTCH SW)
a.

Disconnect the A54 ECM connector.


b.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch / Clutch Switch
for Manual Transaxle

State of clutch pedal


for CVT

Shift position (P and N)


OFF or ON
for Manual Transaxle

OFF: Clutch pedal released

ON: Clutch pedal depressed


for CVT

OFF: Shift lever in any position other than P or N

ON: Shift lever in P or N


for Manual Transaxle
·

Use this item to help determine if the clutch position switch is malfunctioning.

·

The engine cannot be started when this item is "OFF".


for CVT
·

Use this item to determine if the park/neutral position switch assembly is malfunctioning.

·

When the engine cannot be started due to a park/neutral position switch assembly malfunction, OFF is displayed.


Body Electrical > Power Source Control > Data List
Tester Display
Neutral Switch / Clutch Switch
50003 454 207
OK:

The GTS display changes correctly in response to the shift lever or clutch pedal operation.



Result:
Result Proceed to
OK A
NG (for CVT) B
NG (for Manual Transaxle) C



A

REPLACE ECM

B

17.INSPECT PARK/NEUTRAL POSITION SWITCH

C

21.INSPECT CLUTCH START SWITCH ASSEMBLY
17.INSPECT PARK/NEUTRAL POSITION SWITCH

OK

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the D45 park/neutral position switch connector.


c.

Remove the ST NO. 1 relay.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-3 (STA) - D45-5 (L) Always Below 1 Ω
H45-10 (STAR) - A54-23 (NSW) Always Below 1 Ω
H45-10 (STAR) - D45-4 (B) Always Below 1 Ω
H45-3 (STA) or D45-5 (L) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or A54-23 (NSW) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or D45-4 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the H45 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H45-10 (STAR) - Body ground
for Manual Transaxle

Engine switch pressed and held with clutch pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)


for CVT

Engine switch pressed and held with brake pedal depressed (starter on) → Approximately 1 second after engine switch released (starter off)


6 V or higher* → 1.0 V or less


HINT:

*: While the engine is cranking, the auxiliary battery voltage may drop to approximately 6 V.



Result:
Proceed to
OK
NG



OK

20.INSPECT ST NO. 1 RELAY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

20.INSPECT ST NO. 1 RELAY

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE ST NO. 1 RELAY

21.INSPECT CLUTCH START SWITCH ASSEMBLY

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY)

22.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A64 clutch start switch assembly connector.


c.

Remove the ST NO. 1 relay.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-3 (STA) - A64-1 (L) Always Below 1 Ω
H45-10 (STAR) - A54-23 (NSW) Always Below 1 Ω
H45-10 (STAR) - A64-2 (B) Always Below 1 Ω
H45-3 (STA) or A64-1 (L) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or A54-23 (NSW) - Other terminals and body ground Always 10 kΩ or higher
H45-10 (STAR) or A64-2 (B) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-14 (P) - Body ground Shift position P → Shift position not P 9V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
24.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H20 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-14 (P) - H20-3 (P2) Always Below 1 Ω
H46-14 (P) or H20-3 (P2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

25.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.

Reconnect the H46 certification ECU (smart key ECU assembly) connector.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-14 (P) - Body ground Shift position P 9 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE SHIFT CONTROL UNIT ASSEMBLY

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

26.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - AUXILIARY BATTERY AND GROUND)
a.

Disconnect the A63 stop light switch assembly connector.


b.
E409581C46
1.458,0.094 1.958,0.344 0.5,0.25 2.625,1.917 2.458,1.917 2.458,1.917 2.313,1.344 true 0.979,1.896 1.146,1.896 1.146,1.896 1.313,1.365 true 0.115,0.125 0.427,0.281 0.313,0.156 10 false *a 1.594,0.146 1.906,0.302 0.313,0.156 10 false A63 2.698,1.833 3.01,1.99 0.313,0.156 10 false B 0.698,1.823 1.01,1.979 0.313,0.156 10 false GND
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A63-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

27.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.INSPECT STOP LIGHT SWITCH ASSEMBLY

OK

28.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

28.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A63 stop light switch assembly connector.


c.

Disconnect the A54 ECM connector.


d.

Disconnect the A36 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the D71 transmission control ECU connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-21 (STP1) - A63-3 (L) Always Below 1 Ω
H45-21 (STP1) or A63-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR