The skid control ECU (brake booster with master cylinder assembly) controls braking force according to the hybrid control system regenerative braking force and provides the hydraulic pressure necessary for operating the master cylinder and each wheel cylinder according to the servo pressure sensor.
DTCs may be stored if one of the following occurs:
Brake fluid leaks.
Wheel cylinder vibrates due to uneven wear of a brake disc.
Foreign matter enters a solenoid valve.
Line pressure drops during air bleeding.
Brake pads are replaced.
Rotors are replaced.
When replacing the brake pads, retracting the brake caliper pistons and installing new brake pads will greatly increase the clearance between the brake pads and brake discs. This will result in a significant possibility of this DTC being stored the next time the brake pedal is depressed. As this is not a malfunction, clear the DTC if it is stored for this reason.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C139A00 | Brake Pressure Control solenoid Circuit Malfunction | Malfunction in one of the two circuits (leakage, etc.). | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Brake actuator (brake booster with master cylinder assembly) |
Brake |
| C139B7E | Brake Pressure Control solenoid "A" Actuator Stuck On | SLA valve malfunction (stuck, etc.). | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Brake actuator (brake booster with master cylinder assembly) |
Brake |
| C13CD00 | Brake Pressure Too Low | Fluid pressure control performance degraded (high pressure). | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Brake actuator (brake booster with master cylinder assembly) |
Brake |
| C13CE00 | Brake Pressure Too High | Fluid pressure control performance degraded (low pressure). | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Brake actuator (brake booster with master cylinder assembly) |
Brake |
| C140000 | Brake Pressure Leak Malfunction | Malfunction (leakage, etc.) detected in the ABS decrease pressure valve in the brake actuator assembly. | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Brake actuator (brake booster with master cylinder assembly) |
Brake |
| C14EC7E | Brake Pressure Control solenoid "C" Actuator Stuck On | SSA valve malfunction (stuck, etc.). | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Brake actuator (brake booster with master cylinder assembly) |
Brake |
| C14F47E | Brake Pressure Control solenoid "D" Actuator Stuck On | SGH valve malfunction (stuck, etc.). | ·
Brake fluid leaks ·
Uneven brake disc rotor wear ·
Brake actuator (brake booster with master cylinder assembly) |
Brake |
Refer to DTC C12A512.
After replacing the brake booster with master cylinder assembly or brake actuator assembly, perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".
Interview the customer to check the vehicle conditions when the brake system warning light (yellow indicator) illuminated.
Using the GTS, check for Freeze Frame Data that is recorded when a DTC is stored.
Freeze Frame Data is only stored once when a DTC is stored.
If other DTCs are output, repair any malfunctions related to those DTCs first, and then reproduce the conditions that caused any of the DTCs to be stored based on the interview with the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Check that there are no fluid leaks in the brake lines between the brake booster with master cylinder assembly and the wheel cylinders.
Check that there is no brake fluid leaks from the brake booster with master cylinder assembly or brake actuator assembly body.
Check that the brakes are not dragging.
There are no fluid leaks or dragging.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Perform the air bleeding procedure in Bleed Brake System.
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID (for HV Model)>BLEEDING
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector 3 minutes after the ignition switch is turned off.
Disconnect the A40 brake actuator assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (skid control ECU (brake booster with master cylinder assembly)) | B |
| NG (brake actuator assembly) | C |
A
B
C
Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Reconnect the A40 brake actuator assembly connector.
Measure the voltage and resistance on the wire harness side.
Voltage and resistance readings are all normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A40 brake actuator assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-14 (+BS) - A40-38 (+BS) | Always | Below 1 Ω |
| A38-14 (+BS) or A40-38 (+BS) - Body ground | Always | 10 kΩ or higher |
| A38-48 (SFRH) - A40-37 (SFRH) | Always | Below 1 Ω |
| A38-48 (SFRH) or A40-37 (SFRH) - Body ground | Always | 10 kΩ or higher |
| A38-49 (SFLH) - A40-8 (SFLH) | Always | Below 1 Ω |
| A38-49 (SFLH) or A40-8 (SFLH) - Body ground | Always | 10 kΩ or higher |
| A38-50 (SRRH) - A40-34 (SRRH) | Always | Below 1 Ω |
| A38-50 (SRRH) or A40-34 (SRRH) - Body ground | Always | 10 kΩ or higher |
| A38-51 (SRLH) - A40-11 (SRLH) | Always | Below 1 Ω |
| A38-51 (SRLH) or A40-11 (SRLH) - Body ground | Always | 10 kΩ or higher |
| A38-44 (SFRR) - A40-31 (SFRR) | Always | Below 1 Ω |
| A38-44 (SFRR) or A40-31 (SFRR) - Body ground | Always | 10 kΩ or higher |
| A38-45 (SFLR) - A40-2 (SFLR) | Always | Below 1 Ω |
| A38-45 (SFLR) or A40-2 (SFLR) - Body ground | Always | 10 kΩ or higher |
| A38-46 (SRRR) - A40-28 (SRRR) | Always | Below 1 Ω |
| A38-46 (SRRR) or A40-28 (SRRR) - Body ground | Always | 10 kΩ or higher |
| A38-47 (SRLR) - A40-5 (SRLR) | Always | Below 1 Ω |
| A38-47 (SRLR) or A40-5 (SRLR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the DTCs that are output.
| Result | Proceed to |
|---|---|
| C139B7E, C13CD00 or C13CE00 is output | A |
| Only C139A00 is output | B |
| C14EC7E or C14F47E is output | C |
| Only C140000 is output | D |
A
B
C
D
Connect an LSPV gauge set.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa, Max.: 24.48 MPa | Brake pedal released: 0.00 to 2.10 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Tester Display |
|---|
| Servo Pressure |
Depress the brake pedal slowly and check the servo pressure output values with respect to the wheel cylinder pressure values for each wheel.
| Hydraulic Pressure
[MPa (kgf/cm2, psi)] |
Servo Pressure
[MPa] |
|---|---|
| 2.0 (20.4, 290) | 0.3 to 4.3 |
| 5.0 (51.0, 725) | 3.3 to 7.3 |
| 7.0 (71.4, 1015) | 5.3 to 9.3 |
| Hydraulic Pressure
[MPa (kgf/cm2, psi)] |
Servo Pressure
[MPa] |
|---|---|
| 2.0 (20.4, 290) | 0.3 to 4.3 |
| 5.0 (51.0, 725) | 3.3 to 7.3 |
| 7.0 (71.4, 1015) | 5.3 to 9.3 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the A27 brake pedal stroke sensor assembly connector.
Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.
Brake pedal does not vibrate during braking.
An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.
The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.
If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.
The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.
Uneven disc wear can be checked by measuring the disc thickness variation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Reconnect the A27 brake pedal stroke sensor assembly connector.
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Turn the ignition switch off and wait for 3 minutes or more.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C139B7E, C13CD00 and C13CE00 are not output | A |
| C139B7E, C13CD00 or C13CE00 is output | B |
If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Connect an LSPV gauge set.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Servo Pressure | Pressure value of servo | Min.: 0.00 MPa, Max.: 24.48 MPa | Brake pedal released: 0.00 to 2.10 MPa | Brake pedal is being depressed: Changes in proportion to the depression force of the brake pedal |
| Tester Display |
|---|
| Servo Pressure |
Depress the brake pedal slowly and check the servo pressure output values with respect to the wheel cylinder pressure values for each wheel.
| Hydraulic Pressure
[MPa (kgf/cm2, psi)] |
Servo Pressure
[MPa] |
|---|---|
| 2.0 (20.4, 290) | 0.3 to 4.3 |
| 5.0 (51.0, 725) | 3.3 to 7.3 |
| 7.0 (71.4, 1015) | 5.3 to 9.3 |
| Hydraulic Pressure
[MPa (kgf/cm2, psi)] |
Servo Pressure
[MPa] |
|---|---|
| 2.0 (20.4, 290) | 0.3 to 4.3 |
| 5.0 (51.0, 725) | 3.3 to 7.3 |
| 7.0 (71.4, 1015) | 5.3 to 9.3 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the A27 brake pedal stroke sensor assembly connector.
Perform a road test according to Freeze Frame Data or customer problem analysis. While driving, check for abnormal brake pedal vibration caused by brake discs that are worn or have excess runout.
Brake pedal does not vibrate during braking.
An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.
The brake pedal does not kick back due to caliper piston vibration during electronically controlled brake system control.
If the brake pedal stroke sensor assembly connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.
The Active Test does not prohibit electronically controlled brake system control when the vehicle is being driven, so disconnect the brake pedal stroke sensor assembly connector before continuing with inspection.
Uneven disc wear can be checked by measuring the disc thickness variation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Reconnect the A27 brake pedal stroke sensor assembly connector.
Clear the DTCs.
Turn the ignition switch off.
Mount a pedal effort gauge.
Turn the ignition switch to ON (READY) and depress the brake pedal once.
Depress the brake pedal after turning the ignition switch ON (READY) to set the vehicle to linear mode (switching solenoid (SSA) on).
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor assembly | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.65 to 1.35 V | Reading increases when brake pedal is depressed |
| Stroke Sensor2 | Brake pedal stroke sensor assembly 2 | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 3.65 to 4.35 V | Reading decreases when brake pedal is depressed |
| Tester Display |
|---|
| Stroke Sensor |
| Stroke Sensor2 |
Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.
Perform this procedure in linear mode (switching solenoid (SSA) on).
| Brake Effort
[N (kgf, lbf)] |
Stroke Sensor
[V] |
Stroke Sensor2
[V] |
|---|---|---|
| 50 (5, 11.2) | 1.13 to 1.83 | 3.17 to 3.87 |
| 100 (10, 22.5) | 1.26 to 1.96 | 3.04 to 3.74 |
| 200 (20, 45.0) | 1.41 to 2.11 | 2.89 to 3.59 |
| 500 (51.0, 112.4) | 1.42 to 2.12 | 2.88 to 3.58 |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Turn the ignition switch off and wait for 3 minutes or more.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C139A00 is not output | A |
| C139A00 is output | B |
If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Turn the ignition switch off and wait for 3 minutes or more.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C14EC7E and C14F47E are not output | A |
| C14EC7E or C14F47E is output | B |
If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Mount a pedal effort gauge.
Disconnect the A30 brake booster pump assembly connector.
Depress the brake pedal 10 times or more until it becomes hard.
Depressing the brake pedal with the connector of the brake booster pump assembly disconnected drops the accumulator pressure to approximately 0 MPa.
Connect an LSPV gauge set.
Select the Data List on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.65 to 1.35 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Stroke Sensor |
Slowly depress the brake pedal and check the brake pedal stroke sensor assembly output voltages and the wheel cylinder pressure with respect to brake pedal depression force.
Check the wheel cylinder pressure with the switching solenoid (SSA, SGH) off and an accumulator pressure of 0 MPa.
| Brake Effort
[N (kgf, lbf)] |
Stroke Sensor
[V] |
Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi)) |
|---|---|---|
| 200 (20, 45.0) | 1.24 to 1.94 | 0.06 to 2.06 (0.6 to 21.0, 9 to 299) |
| 500 (51, 112.4) | 1.41 to 2.11 | 2.09 to 4.09 (21.3 to 41.7, 303 to 593) |
| Brake Effort
[N (kgf, lbf)] |
Stroke Sensor
[V] |
Wheel Hydraulic Pressure
(MPa (kgf/cm2, psi)) |
|---|---|---|
| 200 (20, 45.0) | 1.24 to 1.94 | 0.06 to 2.06 (0.6 to 21.0, 9 to 299) |
| 500 (51, 112.4) | 1.41 to 2.11 | 2.09 to 4.09 (21.3 to 41.7, 303 to 593) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Reconnect the A30 brake booster pump assembly connector.
Clear the DTCs.
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
Turn the ignition switch off and wait for 3 minutes or more.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C140000 is not output | A |
| C140000 is output | B |
If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B