Home › Drivetrain › EC6E (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2020.03–2020.07
RM36W0E _52 Drivetrain _089427 EC6E MANUAL TRANSMISSION / TRANSAXLE _0424701 TRANSMISSION CONTROL CABLE A

EC6E MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 5.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 51447D 7.REMOVE CENTER NO. 4 ENGINE UNDER COVER

Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58153 10.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
C429238

Remove 4 nuts and front No. 2 floor heat insulator from the vehicle body.


Hide 58151 11.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
C434360

Remove nut and front No. 1 floor heat insulator from the vehicle body.


Hide 33820B 12.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C435416C01
2.76,1.271 2.417,1.271 true 1.865,1.177 1.865,1.531 true 1.802,1.563 2,1.74 0.198,0.177 10 true *a 2.792,1.188 2.99,1.354 0.198,0.167 10 true *b
*a Transmission Control Select Cable
*b Transmission Control Shift Cable


Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.


b.

Disconnect the transmission control shift cable from the floor shift shift lever assembly.


c.
C435418

Using a screwdriver, pull out the stopper of the transmission control select cable.

NOTICE:

Do not remove the stopper. If it is removed, reinstall it to its original position.



d.
C435410

Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control select cable from the shift lever assembly.

NOTICE:
·

Do not rotate the nut excessively as the internal spring may jump out and the transmission control cable assembly will not be reusable.

·

Do not forcibly pull the transmission control cable assembly into the cabin.




e.

Disconnect the transmission control shift cable from the floor shift lever assembly in the same manner as the transmission control select cable.


f.
C435411N01
0.885,1.115 1.042,1.302 0.156,0.188 10 true A 2.542,1.448 2.698,1.635 0.156,0.188 10 true A 0.833,0.385 0.99,0.573 0.156,0.188 10 true B 2.406,0.542 2.563,0.729 0.156,0.188 10 true B

Remove the 2 clips (A) to disconnect the transmission control cable assembly from the manual transaxle assembly.


g.

Remove the 2 clips (B) to disconnect the transmission control cable assembly from the control cable bracket assembly.


h.
C435412

Remove the nut.


i.

Disengage the guide and disconnect the transmission control cable assembly from the vehicle body.


j.
C435413

Remove the 2 nuts and transmission control cable assembly from the vehicle body.