Home › Drivetrain › EC6E (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2020.03–2020.07
RM36W0E _52 Drivetrain _089427 EC6E MANUAL TRANSMISSION / TRANSAXLE _0424701 TRANSMISSION CONTROL CABLE A

EC6E MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33820B 1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Engage the guide and connect the transmission control cable assembly to the vehicle body.


c.

Install the nut.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


d.
C435411C01
1.594,0.594 2.219,0.323 2.219,0.323 1.99,0.802 true 2.25,0.208 2.427,0.396 0.177,0.188 10 true *a 0.865,0.552 1.01,0.729 0.146,0.177 10 true B 2.365,0.698 2.51,0.875 0.146,0.177 10 true B 2.5,1.677 2.646,1.854 0.146,0.177 10 true A 0.979,1.365 1.125,1.542 0.146,0.177 10 true A
*a Paint Mark


Install the transmission control cable assembly to the control cable bracket assembly with 2 new clips (B).

NOTICE:

Make sure that the paint marks on the transmission control cable assembly are aligned with the slits in the control cable bracket assembly before installing the clips.



e.

Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips (A).


f.
C435414C01
2.156,2.302 2.719,1.531 2.719,1.531 2.042,0.844 true 1.917,1.302 2.198,1.438 true 2.063,0.24 2.375,0.438 0.313,0.198 10 false *d 2.76,1.438 3.073,1.635 0.313,0.198 10 false *b 1.365,0.448 1.594,0.656 0.229,0.208 10 false *c 2.198,1.344 2.427,1.552 0.229,0.208 10 false *a
*a Nut
*b Stopper
*c Turn
*d Push


Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, press in the stopper.


g.
C435415C01
1.104,0.677 1.677,0.323 1.677,0.323 2.615,0.542 true 1.573,0.115 1.885,0.313 0.313,0.198 10 false *a
*a Stopper


Install the transmission control shift cable to the floor shift lever assembly, check that the position of the stopper is the same as shown in the illustration.

NOTICE:

Do not forcibly pull the transmission control cable assembly into the cabin.



h.

Install the transmission control select cable to the floor shift lever assembly, check tthat the position of the stopper is the same as shown in the illustration.

NOTICE:

Do not forcibly pull the transmission control cable assembly into the cabin.



i.
C435423C01
1.917,1.583 1.917,1.167 true 2.75,1.25 2.417,1.25 true 2.75,1.167 3.01,1.375 0.26,0.208 10 true *2 1.833,1.583 2.094,1.792 0.26,0.208 10 true *1
*1 Transmission Control Select Cable
*2 Transmission Control Shift Cable


Connect the transmission control shift cable assembly to the shift lever assembly.


j.

Connect the transmission control select cable to the floor shift lever assembly with the clip.


Hide 33820B 2.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 58910C 3.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 58151 4.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle body with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 58153 5.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR

a.

Install the front No. 2 floor heat insulator to the vehicle body with the 4 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 6.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 74404A 7.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 17701 9.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 10.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 13. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART