Home › Drivetrain › EC6E (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2020.03–2020.07
RM36W0E _52 Drivetrain _089427 EC6E MANUAL TRANSMISSION / TRANSAXLE _0424701 TRANSMISSION CONTROL CABLE N

EC6E MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  ADJUSTMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Parking support brake system (Click here)
·

Air intake system parts

·

Exhaust system parts


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC P063051 is output (Click here)
ECU security key Vehicle control history (RoB) are stored (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 5.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 7.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 58910C 8.REMOVE CONSOLE BOX ASSEMBLY REAR

Hide 33820B 9.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

HINT:
·

After the floor shift shift lever assembly or the transmission control cable assembly is replaced, be sure to adjust the transmission control cable assembly.

·

If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the transmission control cable assembly must be adjusted.



a.
C432076

Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.


b.
C405382C03
1.792,1.76 1.865,1.583 1.865,1.583 2.094,1.583 false 0.885,2.427 1.083,2.427 1.083,2.427 1.177,2.583 false 2.125,1.479 2.438,1.635 0.313,0.156 10 false *a 0.729,2.333 1.042,2.49 0.313,0.156 10 false *b 1.458,1.406 1.771,1.563 0.313,0.156 10 false *c 0.854,0.844 1.167,1 0.313,0.156 10 false *d 1.698,0.979 2.01,1.135 0.313,0.156 10 false *c 1.365,2.375 1.677,2.531 0.313,0.156 10 false *d
*a Slider
*b Lock Piece
*c Slide
*d Pull


Slide the slider of the transmission control select cable in the direction indicated by the arrow in the illustration and pull the lock piece outward.


c.
C401634C02
1.302,1.24 1.521,1.052 true 1.156,1.219 1.333,1.375 0.177,0.156 10 true *a
*a Lock Piece


Connect the transmission control select cable to the floor shift lever assembly and install the clip.

NOTICE:
·

Check that the lock piece is pulled out.

·

Push the end of the transmission control select cable all the way to the base of the floor shift shift lever assembly pin.

·

Connect the transmission control select cable so that the lock piece faces the driver side.




d.
C432096C02
1.677,1.417 2.01,1.958 true 1.781,0.698 2.042,0.427 true 0.938,2.875 1.385,3.375 true 2.052,1.917 2.25,2.094 0.198,0.177 10 true *1 2.073,0.323 2.281,0.51 0.208,0.188 10 true *2 0.719,2.781 1.031,2.938 0.313,0.156 10 true *a
*1 Outer Select Lever
*2 Reverse Restrict Pin Assembly
*a Secured


Hook the outer select lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.


e.
C432097C02
0.698,2.073 0.833,2.219 true 0.5,2.302 0.656,2.427 true 0.5,1.948 0.667,2.125 0.167,0.177 10 true *a 0.323,2.219 0.51,2.396 0.188,0.177 10 true *b
*a Slider Shaft
*b Cam Wall


Push the slider shaft against the cam wall.

NOTICE:
·

Do not pull up the slider shaft.

·

When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.




f.
C329174C02
0.99,0.479 1.125,0.479 1.125,0.479 1.26,0.99 false 1.99,0.302 1.854,0.302 1.854,0.302 1.76,0.76 false 2.052,0.208 2.313,0.417 0.26,0.208 10 false *a 0.813,0.396 1.104,0.594 0.292,0.198 10 false *b 1.698,2.979 2.01,3.135 0.313,0.156 10 false *c
*a Lock Piece
*b Adjuster Case
*c Push in


Push the lock piece into the adjuster case.

NOTICE:
·

Securely push in the lock piece until the 2 claws are engaged.

·

When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.




g.
C432098C02
1.135,1.417 1.469,1.344 true 1.698,0.396 1.708,0.906 true 0.927,1.313 1.125,1.479 0.198,0.167 10 true *1 1.542,0.313 1.854,0.469 0.313,0.156 10 false *2 0.927,3.438 1.104,3.625 0.177,0.188 10 true *a
*1 Outer Select Lever
*2 Reverse Restrict Pin Assembly
*a Released


Move the shift lever to the reverse position, so that the outer select lever can be released.


Hide 58910C 10.INSTALL CONSOLE BOX ASSEMBLY REAR

Hide 74404A 11.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 17701 13.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 14.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 16. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART