Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1.REMOVE REAR WHEEL
42431D
2.REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)
3.DISCONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for Rear Disc Brake)
Disconnect the No. 2 parking brake wire assembly connector from the parking brake actuator assembly.
Remove any dirt or foreign matter on and around the No. 2 parking brake wire assembly connector before performing this step.
Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.
4.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for Rear Disc Brake)
Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle beam assembly.
Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.
5.REMOVE REAR DISC (for Rear Disc Brake)
42312E
6.REMOVE REAR AXLE HUB BOLT (for Rear Drum Brake)
| *a | Service Nut |
| *b | Hold |
| *c | Turn |
Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Install the service nuts to prevent damage to the rear axle hub bolts.
Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly remove the rear axle hub bolt.
Do not damage the threads of the rear axle hub bolts.
42312E
7.REMOVE REAR AXLE HUB BOLT (for Rear Disc Brake)
| *a | Service Nut |
| *b | Hold |
| *c | Turn |
Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Install the service nuts to prevent damage to the rear axle hub bolts.
Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly remove the rear axle hub bolt.
Do not damage the threads of the rear axle hub bolts.
42312E
8.INSTALL REAR AXLE HUB BOLT (for Rear Drum Brake)
Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
| *a | Service Nut |
| *b | Washer |
| *c | Hold |
| *d | Turn |
Install a washer and service nut to the rear axle hub bolt as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Recommended washer thickness is 5 mm (0.197 in.) or more.
Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
Install the service nuts to prevent damage to the rear axle hub bolts.
Do not damage the threads of the rear axle hub bolts.
Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
42312E
9.INSTALL REAR AXLE HUB BOLT (for Rear Disc Brake)
Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.
| *a | Service Nut |
| *b | Washer |
| *c | Hold |
| *d | Turn |
Install a washer and service nut to the rear axle hub bolt as shown in the illustration.
Thread diameter: 12.0 mm (0.472 in.)
Thread pitch: 1.5 mm (0.0591 in.)
Recommended washer thickness is 5 mm (0.197 in.) or more.
Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.
Install the service nuts to prevent damage to the rear axle hub bolts.
Do not damage the threads of the rear axle hub bolts.
Remove the 3 service nuts and washer from the 3 rear axle hub bolts.
42431D
10.INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)
11.INSTALL REAR DISC (for Rear Disc Brake)
12.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for Rear Disc Brake)
Install the rear disc brake caliper assembly to the rear axle beam assembly with the 2 bolts.
13.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY (for Rear Disc Brake)
Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.
14.INSTALL REAR WHEEL