Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2020.07–2020.09
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0420300 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies*1. The power window regulator motor assemblies have motor, regulator and ECU functions.

This DTC is stored when the ECU built into a power window regulator motor assembly and multiplex network master switch assembly determine that the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly*1 is stuck.

*1: w/ Rear Power Window


Master Switch
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2312 Power Window Switch Malfunction
·

Multiplex network master switch assembly stuck

·

Multiplex network master switch assembly held in same position for more than 20 seconds

·

Multiplex network master switch assembly operated for 20 seconds or more


Multiplex network master switch assembly Master Switch

D-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2312 Power Window Switch Malfunction
·

Multiplex network master switch assembly stuck

·

Multiplex network master switch assembly held in same position for more than 20 seconds


·

Multiplex network master switch assembly

·

Power window regulator motor assembly (for driver door)

·

Wire harness or connector


D-Door Motor

P-Door Motor
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2312 Power Window Switch Malfunction
·

Power window regulator switch assembly stuck

·

Power window regulator switch assembly held in same position for more than 20 seconds


·

Power window regulator switch assembly

·

Power window regulator motor assembly (for front passenger door)

·

Wire harness or connector


P-Door Motor

RL-Door Motor (w/ Rear Power Window)
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2312 Power Window Switch Malfunction
·

Rear power window regulator switch assembly (for LH door) stuck

·

Rear power window regulator switch assembly (for LH door) held in same position for more than 20 seconds


·

Rear power window regulator switch assembly (for LH door)

·

Power window regulator motor assembly (for rear LH door)

·

Wire harness or connector


RL-Door Motor

RR-Door Motor (w/ Rear Power Window)
DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2312 Power Window Switch Malfunction
·

Rear power window regulator switch assembly (for RH door) stuck

·

Rear power window regulator switch assembly (for RH door) held in same position for more than 20 seconds


·

Rear power window regulator switch assembly (for RH door)

·

Power window regulator motor assembly (for rear RH door)

·

Wire harness or connector


RR-Door Motor

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 is stored in the multiplex network master switch assembly and in each power window regulator motor assembly.

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



HINT:

If DTC B2312 is not output again after the DTC has been cleared, the DTC was stored due to the switch being held in the same position continuously.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle specifications.


Result:
Result Proceed to
for LHD without Rear Power Window A
for RHD without Rear Power Window B
for LHD with Rear Power Window C
for RHD with Rear Power Window D



A

2.CHECK FOR DTC

B

3.CHECK FOR DTC

C

4.CHECK FOR DTC

D

11.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144

Result:
Result Proceed to
Any Master Switch DTCs in the table below are output A
Any D-Door Motor DTCs in the table below are output B
Any P-Door Motor DTCs in the table below are output C
No DTCs in the table below are output D


Malfunction Status System Related DTCs
Power Window Switch Malfunction Master Switch B2312 ON Switch Failure
D-Door Motor B2312 Master Switch of Driver side door Malfunction
P-Door Motor B2312 Power Window Switch of Passenger side door Malfunction


A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

5.READ VALUE USING GTS (D-DOOR MOTOR)

C

8.READ VALUE USING GTS (P-DOOR MOTOR)

D

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

3.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144

Result:
Result Proceed to
Any Master Switch DTCs in the table below are output A
Any D-Door Motor DTCs in the table below are output B
Any P-Door Motor DTCs in the table below are output C
No DTCs in the table below are output D


Malfunction Status System Related DTCs
Power Window Switch Malfunction Master Switch B2312 ON Switch Failure
D-Door Motor B2312 Master Switch of Driver side door Malfunction
P-Door Motor B2312 Power Window Switch of Passenger side door Malfunction


A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

12.READ VALUE USING GTS (D-DOOR MOTOR)

C

15.READ VALUE USING GTS (P-DOOR MOTOR)

D

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

4.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
Body Electrical > RL-Door Motor > Trouble Codes
50001 146
Body Electrical > RR-Door Motor > Trouble Codes
50001 145

Result:
Result Proceed to
Any Master Switch DTCs in the table below are output A
Any D-Door Motor DTCs in the table below are output B
Any P-Door Motor DTCs in the table below are output C
Any RL-Door Motor DTCs in the table below are output D
Any RR-Door Motor DTCs in the table below are output E
No DTCs in the table below are output F


Malfunction Status System Related DTCs
Power Window Switch Malfunction Master Switch B2312 ON Switch Failure
D-Door Motor B2312 Master Switch of Driver side door Malfunction
P-Door Motor B2312 Power Window Switch of Passenger side door Malfunction
RL-Door Motor B2312 Power Window Switch of Rear Left side door Malfunction
RR-Door Motor B2312 Power Window Switch of Rear Right side door Malfunction


A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

5.READ VALUE USING GTS (D-DOOR MOTOR)

C

8.READ VALUE USING GTS (P-DOOR MOTOR)

E

21.READ VALUE USING GTS (RR-DOOR MOTOR)

F

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

5.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated
-
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

6.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
6.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the L7 power window regulator motor assembly (for driver door) connector.


procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L7-10 (UP) - Body ground Ignition switch ON 11 to 14 V
L7-7 (DOWN) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
7.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

Pre-procedure1

a.

Disconnect the L13 multiplex network master switch assembly connector.


procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L13-20 (UP) or L7-10 (UP) - Body ground Always 10 kΩ or higher
L13-15 (DOWN) or L7-7 (DOWN) - Body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON OFF: Front passenger door power window auto up or auto down switch not being operated
ON: Front passenger door power window auto up or auto down switch being operated
-
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated
-
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated
-
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
P Door P/W Up SW
P Door P/W Down SW
50003 144 1,2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

9.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
9.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK

10.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

Pre-procedure1

a.

Disconnect the K7 power window regulator motor assembly (for Front Passenger Door) connector.


procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K13-5 (UP) or K7-10 (UP) - Body ground Always 10 kΩ or higher
K13-8 (AUTO) or K7-4 (AUTO) - Body ground Always 10 kΩ or higher
K13-4 (DOWN) or K7-7 (DOWN) - Body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Master Switch > Trouble Codes
50001 148
Body Electrical > D-Door Motor > Trouble Codes
50001 124
Body Electrical > P-Door Motor > Trouble Codes
50001 144
Body Electrical > RL-Door Motor > Trouble Codes
50001 146
Body Electrical > RR-Door Motor > Trouble Codes
50001 145

Result:
Result Proceed to
Any Master Switch DTCs in the table below are output A
Any D-Door Motor DTCs in the table below are output B
Any P-Door Motor DTCs in the table below are output C
Any RL-Door Motor DTCs in the table below are output D
Any RR-Door Motor DTCs in the table below are output E
No DTCs in the table below are output F


Malfunction Status System Related DTCs
Power Window Switch Malfunction Master Switch B2312 ON Switch Failure
D-Door Motor B2312 Master Switch of Driver side door Malfunction
P-Door Motor B2312 Power Window Switch of Passenger side door Malfunction
RL-Door Motor B2312 Power Window Switch of Rear Left side door Malfunction
RR-Door Motor B2312 Power Window Switch of Rear Right side door Malfunction


A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

12.READ VALUE USING GTS (D-DOOR MOTOR)

C

15.READ VALUE USING GTS (P-DOOR MOTOR)

D

18.READ VALUE USING GTS (RL-DOOR MOTOR)

E

21.READ VALUE USING GTS (RR-DOOR MOTOR)

F

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

12.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > D-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated
-
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-
Body Electrical > D-Door Motor > Data List
Tester Display
D Door P/W Up SW
D Door P/W Down SW
50003 124 2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

13.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
13.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Pre-procedure1

a.

Disconnect the K7 power window regulator motor assembly (for driver door) connector.


procedure1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K7-10 (UP) - Body ground Ignition switch ON 11 to 14 V
K7-7 (DOWN) - Body ground Ignition switch ON 11 to 14 V



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door)

NG

14.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))
14.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Door))

Pre-procedure1

a.

Disconnect the K5 multiplex network master switch assembly connector.


procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K5-20 (UP) or K7-10 (UP) - Body ground Always 10 kΩ or higher
K5-15 (DOWN) or K7-7 (DOWN) - Body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > P-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal OFF or ON OFF: Front passenger door power window auto up or auto down switch not being operated
ON: Front passenger door power window auto up or auto down switch being operated
-
P Door P/W Up SW Front passenger door power window manual up switch signal OFF or ON OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated
-
P Door P/W Down SW Front passenger door power window manual down switch signal OFF or ON OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated
-
Body Electrical > P-Door Motor > Data List
Tester Display
P Door P/W Auto SW
P Door P/W Up SW
P Door P/W Down SW
50003 144 1,2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

16.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
16.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY

OK

17.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door))

Pre-procedure1

a.

Disconnect the L7 power window regulator motor assembly (for Front Passenger Door) connector.


procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-5 (UP) or L7-10 (UP) - Body ground Always 10 kΩ or higher
L6-8 (AUTO) or L7-4 (AUTO) - Body ground Always 10 kΩ or higher
L6-4 (DOWN) or L7-7 (DOWN) - Body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RL-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH door power window auto switch signal OFF or ON OFF: Rear LH door power window auto up or auto down switch not being operated
ON: Rear LH door power window auto up or auto down switch being operated
-
RL Door P/W Up SW Rear LH door power window manual up switch signal OFF or ON OFF: Rear LH door power window manual up switch not being operated
ON: Rear LH door power window manual up switch being operated
-
RL Door P/W Down SW Rear LH door power window manual down switch signal OFF or ON OFF: Rear LH door power window manual down switch not being operated
ON: Rear LH door power window manual down switch being operated
-
Body Electrical > RL-Door Motor > Data List
Tester Display
RL Door P/W Auto SW
RL Door P/W Up SW
RL Door P/W Down SW
50003 146 1,2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

19.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)
19.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

OK

20.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door)

20.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for LH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

Pre-procedure1

a.

Disconnect the N4 power window regulator motor assembly (for Rear LH Door) connector.


procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-5 (UP) or N4-10 (UP) - Body ground Always 10 kΩ or higher
N3-4 (DOWN) or N4-7 (DOWN) - Body ground Always 10 kΩ or higher
N3-8 (AUTO) or N4-4 (AUTO) - Body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS.

Body Electrical > RR-Door Motor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH door power window auto switch signal OFF or ON OFF: Rear RH door power window auto up or auto down switch not being operated
ON: Rear RH door power window auto up or auto down switch being operated
-
RR Door P/W Up SW Rear RH door power window manual up switch signal OFF or ON OFF: Rear RH door power window manual up switch not being operated
ON: Rear RH door power window manual up switch being operated
-
RR Door P/W Down SW Rear RH door power window manual down switch signal OFF or ON OFF: Rear RH door power window manual down switch not being operated
ON: Rear RH door power window manual down switch being operated
-
Body Electrical > RR-Door Motor > Data List
Tester Display
RR Door P/W Auto SW
RR Door P/W Up SW
RR Door P/W Down SW
50003 145 1,2,3
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

22.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)
22.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

OK

23.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)

23.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

Pre-procedure1

a.

Disconnect the M4 power window regulator motor assembly (for rear RH door) connector.


procedure1

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M3-5 (UP) or M4-10 (UP) - Body ground Always 10 kΩ or higher
M3-4 (DOWN) or M4-7 (DOWN) - Body ground Always 10 kΩ or higher
M3-8 (AUTO) or M4-4 (AUTO) - Body ground Always 10 kΩ or higher



Post-procedure1

c.

None


Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR