When the speed limiter is turned on using the speed limiter switch, the ECM illuminates the speed limiter indicator and activates the speed limiter system. Each function of the speed limiter system can be activated by operating the cruise control main switch. When the cruise control system is operating, the speed limiter system will not operate.
for M15A-FKS
for 1KR-FE
Before replacing the ECM, refer to Service Bulletin.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Turn the ignition switch to ON.
Turn the dynamic radar cruise control on using the cruise control main switch.
Check the operation of each function by operating the cruise control main switch.
Each function of the dynamic radar cruise control system operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for M15A-FKS | A |
| for 1KR-FE | B |
A
B
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ASL SW | Speed limiter switch signal | OFF or ON | OFF: Speed limiter switch off
ON: Speed limiter switch on |
- |
| Tester Display |
|---|
| ASL SW |
The Data List item ASL SW changes according to the operation of the switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A54 ECM connector.
Disconnect the H60 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A54-29 (ASLM) - H60-3 (ASL) | Always | Below 1 Ω |
| H60-2 (ECC) - A54-28 (ECCS) | Always | Below 1 Ω |
| A54-29 (ASLM) or H60-3 (ASL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ASL SW | Speed limiter switch signal | OFF or ON | OFF: Speed limiter switch off
ON: Speed limiter switch on |
- |
| Tester Display |
|---|
| ASL SW |
The Data List item ASL SW changes according to the operation of the switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A55 ECM connector.
Disconnect the H60 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A55-27 (ASLM) - H60-3 (ASL) | Always | Below 1 Ω |
| H60-2 (ECC) - A55-30 (ECCS) | Always | Below 1 Ω |
| A55-27 (ASLM) or H60-3 (ASL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG