The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel tank assembly removal/installation are shown below.
Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
1. PRECAUTION
| *a | Cord |
When removing and storing the fuel tank assembly, arrange the inlet hose as shown in the illustration, and secure the fuel tank assembly using a cord or similar.
Depending on the arrangement of the inlet hose during storage, the inlet hose and rear suspension may interfere and cause fuel leakage.
2.DRAIN FUEL
3.REMOVE WHEEL ASSEMBLY
52592
4.REMOVE REAR BUMPER SIDE SEAL LH (for TMMF Made)
65638
5.REMOVE REAR WHEEL HOUSE LINER LH (for TMMF Made)
Remove the 2 screws.
Remove the 10 clips.
Remove the grommet and rear fender liner.
65638
6.SEPARATE REAR WHEEL HOUSE LINER LH (for TMC Made)
Remove the 2 screws.
Remove the 5 clips.
Remove the grommet and separate the rear fender liner.
77020A
7.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
77310A
8.REMOVE FUEL TANK CAP ASSEMBLY
51447D
9.REMOVE NO. 4 CENTER ENGINE UNDER COVER (for TMMF Made)
51447D
10.REMOVE NO. 4 CENTER ENGINE UNDER COVER (for TMC Made)
17410
11.REMOVE FRONT EXHAUST PIPE ASSEMBLY
77606
12.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
Remove the 3 clips and No. 1 fuel tank protector sub-assembly from the fuel tank assembly.
77027B
13.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
Disconnect the No. 1 fuel emission tube sub-assembly from the fuel tank filler pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
77209F
14.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disconnect the fuel tank main tube sub-assembly from the fuel tank filler pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
58415Q
15.REMOVE NO. 1 REAR FLOOR BOARD (for TMMF Made)
77730C
16.DISCONNECT NO. 2 CHARCOAL CANISTER ASSEMBLY (for TMMF Made)
Disconnect the canister air tube from the No. 2 canister.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
Disengage the clamp to separate the No. 1 canister outlet hose sub-assembly from the fuel tank assembly.
17.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY (for TMMF Made)
Remove the bolt.
Disengage the 2 clamps.
Disengage the locations shown in the illustration, and disengage the fuel tank filler pipe sub-assembly from the vehicle body.
18.DISCONNECT FUEL TANK FILLER PIPE SUB-ASSEMBLY (for TMC Made)
Remove the bolt.
Disengage the locations shown in the illustration, and disengage the fuel tank filler pipe sub-assembly from the vehicle body.
77100U
19.REMOVE FUEL TANK ASSEMBLY
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
Support the fuel tank assembly using an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Remove the 4 bolts.
Lower the engine lifter to remove the fuel tank assembly.
Be careful not to drop the fuel tank assembly.
When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
77209F
20.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.
77027B
21.REMOVE NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
Disengage the 4 clamps to remove the No. 1 fuel emission tube sub-assembly from the fuel tank assembly.
77217A
22.REMOVE NO. 2 FUEL TANK FILLER PIPE SUPPORT
Disengage the 2 claws to remove the No. 2 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.
77216A
23.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT (for TMMF Made)
Disengage the 2 clamps to remove the No. 1 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.
77216A
24.REMOVE NO. 1 FUEL TANK FILLER PIPE SUPPORT (for TMC Made)
Disengage the 3 clamps to remove the No. 1 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.
77218A
25.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT (for TMMF Made)
Disengage the 2 clamps to remove the No. 3 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.
77218A
26.REMOVE NO. 3 FUEL TANK FILLER PIPE SUPPORT (for TMC Made)
Disengage the 3 clamps to remove the No. 3 fuel tank filler pipe support from the fuel tank filler pipe sub-assembly.
77277R
27.REMOVE FUEL TANK FILLER PIPE PROTECTOR (for TMMF Made)
Disengage the 3 claws.
Disengage the 3 clamps to remove the fuel tank filler pipe protector from the fuel tank filler pipe sub-assembly.
77277R
28.REMOVE FUEL TANK FILLER PIPE PROTECTOR (for TMC Made)
Disengage the 4 claws.
Disengage the 4 clamps to remove the fuel tank filler pipe protector from the fuel tank filler pipe sub-assembly.