Home › Engine / Hybrid System › CRUISE CONTROL › SPEED LIMITER SYSTEM (for HV Model) › from 2020.07
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0431302 SPEED LIMITER SYSTEM(for HV Model) J

CRUISE CONTROL  SPEED LIMITER SYSTEM(for HV Model)  Speed Limiter System does not Operate  


DESCRIPTION

When the speed limiter is turned on using the speed limiter switch, the hybrid vehicle control ECU illuminates the speed limiter indicator and activates the speed limiter system. Each function of the speed limiter system can be activated by operating the cruise control main switch. When the cruise control system is operating, the speed limiter system will not operate.

WIRING DIAGRAM

C410619E04
0.958,0.792 2.354,1.229 1.396,0.438 10 false Speed Limiter Switch 2.49,0.604 2.802,0.802 0.313,0.198 10 false z2 2.479,1.458 2.792,1.656 0.313,0.198 10 false z2 2.479,0.417 2.792,0.615 0.313,0.198 10 false 11 2.469,1.26 2.781,1.458 0.313,0.198 10 false 12 3.656,0.521 4.042,0.708 0.385,0.188 10 false ASL 3.625,1.375 4.073,1.573 0.448,0.198 10 false ECC 4.063,0.625 4.448,0.813 0.385,0.188 10 false H60 4.063,1.458 4.448,1.646 0.385,0.188 10 false H60 4.146,0.417 4.531,0.604 0.385,0.188 10 false 3 4.167,1.26 4.552,1.448 0.385,0.188 10 false 2 5.552,0.531 5.938,0.719 0.385,0.188 10 false 30 5.833,0.625 6.333,0.823 0.5,0.198 10 false ASLM 5.302,1.969 5.802,2.167 0.5,0.198 10 false H44 5.302,2.125 7.156,2.365 1.854,0.24 10 false Hybrid Vehicle Control ECU 2.833,2.031 3.938,2.417 1.104,0.385 10 false Spiral Cable Sub-assembly 0.531,2.01 2.563,2.375 2.031,0.365 10 false Steering Pad Switch Assembly 1.99,1.354 2.438,1.552 0.448,0.198 10 false ECC 2,0.521 2.385,0.708 0.385,0.188 10 false ASL

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.


NOTICE:
·

Before replacing the hybrid vehicle control ECU, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.CHECK DYNAMIC RADAR CRUISE CONTROL SYSTEM
a.

Turn the ignition switch to ON.


b.

Turn the dynamic radar cruise control on using the cruise control main switch.


c.

Check the operation of each function by operating the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM (for HV Model)>ROAD TEST


OK:

Each function of the dynamic radar cruise control system operates normally.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (ASL SWITCH)

NG

2.READ VALUE USING GTS (ASL SWITCH)
a.

According to the display on the GTS, read the Data List.

Powertrain > Hybrid Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ASL Switch Speed limiter switch signal OFF or ON OFF: Speed limiter switch off
ON: Speed limiter switch on
-
Powertrain > Hybrid Control > Data List
Tester Display
ASL Switch
50003 397 33
OK:

The Data List item ASL Switch changes according to the operation of the switch.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H44 hybrid vehicle control ECU connector.


b.

Disconnect the H60 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H44-30 (ASLM) - H60-3 (ASL) Always Below 1 Ω
H44-30 (ASLM) or H60-3 (ASL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H60-2 (ECC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

6.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

6.INSPECT STEERING PAD SWITCH ASSEMBLY

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH