Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P042000  Catalyst System Efficiency Below Threshold (Bank 1)  


DESCRIPTION

This vehicle has two heated oxygen sensors. One is located in front of the Three-Way Catalytic Converter (TWC), and the other is mounted behind the TWC. The output signals of the sensors are converted into waveforms inside the ECM. The heated oxygen sensors are used by the ECM to monitor the air fuel ratio, and its signal prompts the ECM to perform air fuel ratio feedback control. As a result, the air fuel ratio is balanced, and the waveform of the heated oxygen sensors regularly oscillates between rich and lean. To determine whether or not the TWC performance has deteriorated, the ECM compares the waveforms of the heated oxygen sensor (sensor 1) and heated oxygen sensor (sensor 2). While the TWC is functioning normally, the waveform of the heated oxygen sensor (sensor 2) fluctuates between rich and lean more slowly than the heated oxygen sensor (sensor 1) waveform. When the heated oxygen sensor (sensor 2) waveform frequently fluctuates, it indicates that the TWC performance has deteriorated.

A318955E03
0.396,0.417 2.167,0.927 1.771,0.51 10 false Waveform of Heated Oxygen Sensor (in front of TWC) 3.135,0.406 4.24,1 1.104,0.594 10 false Normal TWC 4.948,0.417 6.698,0.896 1.75,0.479 10 false Waveform of Heated Oxygen Sensor (behind TWC) 0.313,2.906 2.083,3.417 1.771,0.51 10 false Waveform of Heated Oxygen Sensor (in front of TWC) 3.073,2.906 4.844,3.417 1.771,0.51 10 false Deteriorated TWC 5,2.917 6.76,3.417 1.76,0.5 10 false Waveform of Heated Oxygen Sensor (behind TWC)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P042000 Catalyst System Efficiency Below Threshold (Bank 1) After engine and TWC are warmed up, and while vehicle is driven within predetermined engine speed (3 trip detection logic).
·

Gas leak from exhaust system

·

Heated oxygen sensor (sensor 1)

·

Heated oxygen sensor (sensor 2)

·

Exhaust manifold (TWC: Front Catalyst)


Come on DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine B

CATALYST LOCATION

A468108C01
0.76,1.479 0.917,0.917 0.917,0.917 1.115,0.917 true 0.948,1.615 1.208,1.344 1.208,1.344 1.396,1.344 true 3.615,1.906 3.917,2.24 3.917,2.24 4.146,2.24 true 6.042,0.5 6.25,1.094 6.25,1.094 6.448,1.094 true 1.052,2.479 1.365,2 1.365,2 1.563,2 true 1.156,0.833 1.469,1.031 0.313,0.198 10 false *1 1.427,1.281 1.74,1.479 0.313,0.198 10 false *2 1.615,1.938 1.927,2.135 0.313,0.198 10 false *3 4.198,2.156 4.51,2.354 0.313,0.198 10 false *4 6.479,1.021 6.792,1.219 0.313,0.198 10 false *5 0.333,0.323 0.708,0.563 0.375,0.24 12 false *A
*A w/ Gasoline Particulate Filter - -
*1 Heated Oxygen Sensor (Sensor 1) *2 Exhaust Manifold (TWC: Front Catalyst)
*3 Heated Oxygen Sensor (Sensor 2) *4 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*5 Tail Exhaust Pipe Assembly - -


A468109C01
6.01,0.5 6.281,1.271 6.281,1.271 6.469,1.271 true 3.74,1.823 4.104,2.365 4.104,2.365 4.344,2.365 true 1.146,2.5 1.427,2.052 1.427,2.052 1.594,2.052 true 0.688,1.281 1,0.729 1,0.729 1.188,0.729 true 0.917,1.615 1.219,1.333 1.219,1.333 1.427,1.333 true 0.208,0.135 0.583,0.375 0.375,0.24 12 false *A 1.24,0.635 1.552,0.833 0.313,0.198 10 false *1 1.458,1.271 1.771,1.469 0.313,0.198 10 false *2 1.646,1.979 1.958,2.177 0.313,0.198 10 false *3 4.417,2.271 4.729,2.469 0.313,0.198 10 false *4 6.531,1.177 6.844,1.375 0.313,0.198 10 false *5
*A w/o Gasoline Particulate Filter - -
*1 Heated Oxygen Sensor (Sensor 1) *2 Exhaust Manifold (TWC: Front Catalyst)
*3 Heated Oxygen Sensor (Sensor 2) *4 Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*5 Tail Exhaust Pipe Assembly - -


CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


DTC P042000 is detected when the vehicle is driven at an average vehicle speed of approximately 50 km/h (31 mph) with a city driving pattern for approximately 30 minutes, and then driven for approximately 15 minutes at a constant vehicle speed of between 70 and 90 km/h (43 and 56 mph).

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P042000)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P042000 is output A
P042000 and other DTCs are output B


HINT:

If any DTCs other than P042000 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

Pre-procedure1

a.

Warm up the engine at an engine speed of 2500 rpm for approximately 3 minutes.


Procedure1

b.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Injection Volume
O2 Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 277,1305,218

c.

Monitor the voltage output of the heated oxygen sensor (sensor 1) and heated oxygen sensor (sensor 2) (O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:
The heated oxygen sensors reacts in accordance with increases and decreases of the fuel injection volume:
+12.5% = Rich output:

Higher than 0.55 V

-12.5% = Lean output:

Below 0.4 V


A342237E01
0.135,0.688 0.75,0.885 0.615,0.198 10 false Case 0.229,2.167 0.844,2.365 0.615,0.198 10 false 1 0.25,4.271 0.865,4.469 0.615,0.198 10 false 2 0.24,6.292 0.854,6.49 0.615,0.198 10 false 3 0.26,8.354 0.875,8.552 0.615,0.198 10 false 4 0.771,0.5 2.885,0.906 2.115,0.406 10 false Heated Oxygen Sensor (Sensor 1) Output Voltage 3.469,0.49 5.583,0.896 2.115,0.406 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.948,0.51 6.979,0.906 1.031,0.396 10 false Main Suspected Trouble Area 0.74,1.344 2.031,1.583 1.292,0.24 10 false Injection Volume 1.479,1.594 2.771,1.833 1.292,0.24 9 false 12.5% 1.427,1.854 2.719,2.094 1.292,0.24 9 false -12.5% 0.698,2.302 1.99,2.542 1.292,0.24 10 false Output Voltage 0.792,2.583 2.083,2.823 1.292,0.24 9 false Higher than 0.55 V 1.167,2.844 2.458,3.083 1.292,0.24 9 false Below 0.4 V 2.615,2.688 3.906,2.927 1.292,0.24 9 false OK 4.115,1.594 5.406,1.833 1.292,0.24 9 false 12.5% 4.073,1.823 5.365,2.063 1.292,0.24 9 false -12.5% 3.302,2.292 4.594,2.531 1.292,0.24 10 false Output Voltage 3.375,2.573 4.667,2.813 1.292,0.24 9 false Higher than 0.55 V 3.74,2.844 5.031,3.083 1.292,0.24 9 false Below 0.4 V 5.146,2.677 6.438,2.917 1.292,0.24 9 false OK 6.354,2.177 6.969,2.375 0.615,0.198 10 false - 0.76,3.417 2.052,3.656 1.292,0.24 10 false Injection Volume 1.448,3.698 2.74,3.938 1.292,0.24 9 false 12.5% 1.427,3.917 2.719,4.156 1.292,0.24 9 false -12.5% 0.719,4.385 2.01,4.625 1.292,0.24 10 false Output Voltage 2.615,4.74 3.906,4.979 1.292,0.24 9 false NG 0.729,4.813 2.021,5.052 1.292,0.24 9 false Almost no reaction 3.365,1.333 4.656,1.573 1.292,0.24 10 false Injection Volume 3.396,3.417 4.688,3.656 1.292,0.24 10 false Injection Volume 4.083,3.667 5.375,3.906 1.292,0.24 9 false 12.5% 4.052,3.896 5.344,4.135 1.292,0.24 9 false -12.5% 3.281,4.354 4.573,4.594 1.292,0.24 10 false Output Voltage 3.396,4.677 4.688,4.917 1.292,0.24 9 false Higher than 0.55 V 3.802,4.938 5.094,5.177 1.292,0.24 9 false Below 0.4 V 5.188,4.823 6.479,5.063 1.292,0.24 9 false OK 5.865,3.469 6.969,4.115 1.104,0.646 10 false - Heated oxygen sensor (sensor 1) 5.844,4.25 6.948,4.896 1.104,0.646 10 false - Heated oxygen sensor (sensor 1) circuit 0.719,5.448 2.01,5.688 1.292,0.24 10 false Injection Volume 1.458,5.75 2.75,5.99 1.292,0.24 9 false 12.5% 1.448,5.948 2.74,6.188 1.292,0.24 9 false -12.5% 0.792,6.417 2.083,6.656 1.292,0.24 10 false Output Voltage 0.708,6.729 2,6.969 1.292,0.24 9 false Higher than 0.55 V 1.063,7 2.354,7.24 1.292,0.24 9 false Below 0.4 V 2.563,6.875 3.854,7.115 1.292,0.24 9 false OK 3.365,5.458 4.656,5.698 1.292,0.24 10 false Injection Volume 4.073,5.729 5.365,5.969 1.292,0.24 9 false 12.5% 4.052,5.938 5.344,6.177 1.292,0.24 9 false -12.5% 3.396,6.406 4.688,6.646 1.292,0.24 10 false Output Voltage 3.365,6.885 4.656,7.125 1.292,0.24 9 false Almost no reaction 5.177,6.75 6.469,6.99 1.292,0.24 9 false NG 5.885,5.563 6.99,6.208 1.104,0.646 10 false - Heated oxygen sensor (sensor 2) 5.885,6.333 6.99,6.979 1.104,0.646 10 false - Heated oxygen sensor (sensor 2) circuit 0.75,7.521 2.042,7.76 1.292,0.24 10 false Injection Volume 1.479,7.802 2.771,8.042 1.292,0.24 9 false 12.5% 1.438,8.01 2.729,8.25 1.292,0.24 9 false -12.5% 0.76,8.438 2.052,8.677 1.292,0.24 10 false Output Voltage 0.74,8.917 2.031,9.156 1.292,0.24 9 false Almost no reaction 2.563,8.823 3.854,9.063 1.292,0.24 9 false NG 3.302,7.531 4.594,7.771 1.292,0.24 10 false Injection Volume 4.104,7.802 5.396,8.042 1.292,0.24 9 false 12.5% 4.063,8.042 5.354,8.281 1.292,0.24 9 false -12.5% 3.344,8.396 4.635,8.635 1.292,0.24 10 false Output Voltage 3.385,8.927 4.677,9.167 1.292,0.24 9 false Almost no reaction 5.177,8.802 6.469,9.042 1.292,0.24 9 false NG 5.833,7.802 6.938,8.448 1.104,0.646 10 false - Fuel system 5.833,8.365 6.938,9.01 1.104,0.646 10 false - Gas leak from exhaust system

The following procedure enables the technician to check and graph the voltage output of both the heated oxygen sensors.

To display the graph, enter the following menus:

Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2; then press the view button.


Result:
Result Proceed to
Case 1 A
Case 2 B
Case 3 C
Case 4 D


Post-procedure1

d.

None.



A

3.CHECK FOR EXHAUST GAS LEAK

B

C

4.CHECK FOR EXHAUST GAS LEAK

D

CHECK EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO, AND GO TO STEP 3

3.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leak.



Result:
Proceed to
OK
NG



OK

REPLACE EXHAUST MANIFOLD (TWC: FRONT CATALYST)

NG

REPAIR FOR EXHAUST GAS LEAK POINT

4.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leak.

OK:

No gas leak.



Result:
Proceed to
OK
NG



OK

NG

REPAIR FOR EXHAUST GAS LEAK POINT