Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P010511  Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Ground  P010515  Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P01052A.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P01052A

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P010511 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Ground The output voltage from the vacuum sensor remains 0.43 V or less for 2 seconds or more (3 trip detection logic).
·

Open or short in manifold absolute pressure sensor (intake manifold) circuit

·

Intake manifold

·

ECM


Comes on DTC stored Engine A
P010515 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Short to Battery or Open The output voltage from the vacuum sensor remains 4.84 V or more for 2 seconds or more (3 trip detection logic).
·

Open or short in manifold absolute pressure sensor (intake manifold) circuit

·

Intake manifold

·

ECM


Comes on DTC stored Engine A

HINT:

When any of these DTCs is output, check the manifold absolute pressure using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Manifold Absolute Pressure.

Manifold Absolute Pressure Malfunction
Approximately 0 kPa (0 mmHg)
·

PIM circuit short


130 kPa (975 mmHg) or more
·

VC circuit open or short

·

PIM circuit open

·

E2 circuit open




WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

DTC P010511 and P010515 are detected when the engine idles for approximately 15 seconds.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

If any DTCs related to the manifold absolute pressure sensor, accelerator pedal sensor assembly and camshaft position sensor are output simultaneously, inspect the VC circuit of each component.



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Read the Intake Manifold Absolute Pressure value.

Powertrain > Engine > Data List
Tester Display
Intake Manifold Absolute Pressure
50003 372 385
OK:

Same value as the actual atmospheric pressure


Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 80 and 110 kPa A
None of the above conditions are met B


HINT:

Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)]. For every 100 m (328 ft.) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).

80 to 110 kPa = 600 to 825 mmHg




A

B

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D21-3 (VC) - D21-2 (E2) Ignition switch ON 4.5 to 5.5 V
D21-1 (PIM) - D21-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.REPLACE INTAKE MANIFOLD

NG

6.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
3.REPLACE INTAKE MANIFOLD

NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P010511 OR P010515)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P010511 OR P010515)

Pre-procedure1

a.

Start the engine.


b.

Allow the engine to idle for 15 seconds or more.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTCs are not output A
P010511 or P010515 is output B



Post-procedure1

d.

None.



A

END

B

6.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D21-3 (VC) - D50-95 (VC2) Always Below 1 Ω
D21-1 (PIM) - D50-129 (PIM) Always Below 1 Ω
D21-2 (E2) - D50-127 (E21) Always Below 1 Ω
D21-3 (VC) or D50-95 (VC2) - Body ground Always 10 kΩ or higher
D21-1 (PIM) or D50-129 (PIM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR