Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P001011  "A" Camshaft Position Actuator "A" Control Circuit/Open Bank 1 Circuit Short to Ground  P001012  "A" Camshaft Position Actuator "A" Control Circuit/Open Bank 1 Circuit Short to Battery  P001013  A Camshaft Position Actuator Bank 1 Circuit Open  


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, camshaft timing oil control valve assembly and VVT controller. The ECM sends a target "duty-cycle" control signal to the camshaft timing oil control valve assembly. This control signal, applied to the camshaft timing oil control valve assembly, regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed based on engine operating conditions such as intake air volume, throttle position and engine coolant temperature.

The ECM controls the camshaft timing oil control valve assembly based on the signals from several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, engine torque and fuel economy improve, and the exhaust emissions drop. The ECM detects actual valve timing using signals from the camshaft and crankshaft position sensors. The ECM performs feedback control and verifies target valve timing.

A209140E23
4.394,0.815 6.856,1.027 2.462,0.211 10 Camshaft Position Sensor 4.375,1.325 6.839,1.486 2.464,0.161 10 Crankshaft Position Sensor 0.072,0.015 0.944,0.215 0.872,0.199 10 VVT System: 2.337,1.96 3.613,2.135 1.277,0.174 10 Target Valve Timing 2.337,1.288 3.613,1.462 1.277,0.174 10 Actual Valve Timing 2.687,2.696 3.401,2.870 0.714,0.174 10 Correction 2.826,3.204 3.227,3.379 0.402,0.174 10 ECM 1.602,3.75 4.408,3.896 2.806,0.147 10 Camshaft Timing Oil Control Valve Assembly 0.17,2.69 0.864,2.865 0.695,0.174 10 Duty-cycle 4.394,1.849 6.900,2.071 2.506,0.222 10 Manifold Absolute Pressure Sensor 4.384,2.856 6.895,3.055 2.510,0.199 10 Engine Coolant Temperature Sensor 4.403,2.344 6.863,2.512 2.459,0.167 10 Throttle Position Sensor 4.403,3.361 6.839,3.540 2.436,0.179 10 Vehicle Speed Sensor 0.317,4.27 1.686,4.474 1.369,0.205 10 Engine Oil Pressure 3.663,4.217 7.051,4.397 3.388,0.180 10 VVT Controller (Camshaft Timing Sprocket Assembly) 3.887,4.918 4.988,5.101 1.100,0.184 10 Intake Camshaft 2.566,4.571 2.846,4.275 2.846,4.275 3.611,4.275 false 3.181,4.782 3.323,5.009 3.323,5.009 3.856,5.009 false

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P001011 "A" Camshaft Position Actuator "A" Control Circuit/Open Bank 1 Circuit Short to Ground Short to ground in camshaft timing oil control valve (for Intake Camshaft) circuit (VVT-OCV low side drive circuit) (3 trip detection logic)
·

Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

ECM


Comes on DTC stored Engine A
P001012 "A" Camshaft Position Actuator "A" Control Circuit/Open Bank 1 Circuit Short to Battery Short to power source line in camshaft timing oil control valve (for Intake Camshaft) circuit (VVT-OCV low side drive circuit) (3 trip detection logic)
·

Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

ECM


Comes on DTC stored Engine A
P001013 A Camshaft Position Actuator Bank 1 Circuit Open Open in camshaft timing oil control valve (for Intake Camshaft) circuit (VVT-OCV low side drive circuit) (3 trip detection logic)
·

Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

ECM


Comes on DTC stored Engine A

HINT:

The IC, built into the ECM, detects opens or shorts in the camshaft timing oil control valve assembly (for intake camshaft) circuit.


WIRING DIAGRAM

A322486E05
5.854,2.354 6.354,2.552 0.5,0.198 10 false ECM 0.208,2.073 2.938,2.458 2.729,0.385 10 false Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) 5.208,0.875 5.604,1.042 0.396,0.167 10 false OCV+ 5.208,1.542 5.604,1.708 0.396,0.167 10 false OCV- 1.854,1.531 1.99,1.708 0.135,0.177 10 false 1 1.854,0.865 1.99,1.042 0.135,0.177 10 false 2 0.219,1.885 0.552,2.063 0.333,0.177 10 false D77 5.469,2.354 5.802,2.563 0.333,0.208 10 false D50 4.948,0.875 5.146,1.021 0.198,0.146 10 false 75 4.938,1.531 5.135,1.698 0.198,0.167 10 false 74 1.656,0.865 1.813,1.063 0.156,0.198 10 false + 1.667,1.531 1.823,1.729 0.156,0.198 10 false -

CONFIRMATION DRIVING PATTERN

DTC P0010 is detected when the engine idles for approximately 15 seconds.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Check the engine speed when operating the camshaft timing oil control valve assembly (for intake camshaft) using the GTS.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
Intake VVT OCV Control Duty Ratio Bank 1
50004 372 4 397,296

Result:
Result Proceed to
Engine changes from steady idling to rough idling or engine stalling A
No change in engine speed B


Post-procedure1

d.

None.



A

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)

Pre-procedure1

a.

Disconnect the camshaft timing oil control valve assembly (for intake camshaft) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D77-2 (+) - D50-75 (OCV+) Always Below 1 Ω
D77-1 (-) - D50-74 (OCV-) Always Below 1 Ω
D77-2 (+) or D50-75 (OCV+) - Body ground Always 10 kΩ or higher
D77-1 (-) or D50-74 (OCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR