Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P013011  O2 (A/F) Sensor Circuit Bank 1 Sensor 1 Circuit Short to Ground  


DESCRIPTION

Refer to DTC P013013.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P013013

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P013011 O2 (A/F) Sensor Circuit Bank 1 Sensor 1 Circuit Short to Ground

All of the following conditions are met (3 trip detection logic):

(a)

Fuel-cut operation is not being performed.

(b)

Purge control* of the catalyst is not being performed.

(c)

Heated oxygen sensor (sensor 1) output voltage is less than 0.06 V.

(d)

Conditions (a), (b) and (c) are met for 5 seconds or more.

(e)

Active air-fuel ratio control is performed as follows after condition (d) is met:

(1)

Pulse signal is applied to heated oxygen sensor (sensor 1) signal line.

(2)

Heated oxygen sensor (sensor 1) voltage difference before and after applying pulse signal is calculated.

(3)

Steps (1) and (2) are repeated 2 more times.


(f)

Average difference in heated oxygen sensor (sensor 1) voltage when active air-fuel ratio control is performed 3 times is less than 0.015 V.



·

Heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

ECM


Comes on DTC stored Engine B

HINT:

*: In order to purge oxygen adsorbed to the TWC, the stoichiometric ratio is controlled to rich side.


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P013011)
a.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P013011 is output A
P013011 and other DTCs are output B


HINT:

If may DTCs other than P013011 are output, troubleshoot shoes DTCs first.




A

2.INSPECT HEATED OXYGEN SENSOR (SENSOR 1)

B

GO TO DTC CHART

2.INSPECT HEATED OXYGEN SENSOR (SENSOR 1)

OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D38-4 (OX1A) - D85-126 (OX1A) Always Below 1 Ω
D38-2 (HT1A) - D85-25 (HT1A) Always Below 1 Ω
D38-3 (E1) - D85-125 (E11) Always Below 1 Ω
D38-4 (OX1A) or D85-126 (OX1A) - Body ground Always 10 kΩ or higher
D38-2 (HT1A) or D85-25 (HT1A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013011)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P013011)

Pre-procedure1

a.

Start the engine and warm it up.


Procedure1

b.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
P013011 is output A
DTCs are not output B


Post-procedure1

c.

None.



A

B

END