Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P032511  Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground  P032515  Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open  


DESCRIPTION

The flat type knock control sensor (non-resonant type) has a structure that can detect vibration in a wider band of frequencies, from approximately 5 to 15 kHz, and has the following features:

·

The knock control sensor is fitted on the cylinder block to detect engine knocking.

·

The sensor contains a piezoelectric element which generates a voltage when it becomes deformed.


This occurs when the cylinder block vibrates due to knocking. If engine knocking occurs, the ignition timing is retarded to suppress it.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P032511 Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground

Short to ground in knock sensor circuit:

At least 0.5 second after engine was started, at engine speed higher than 680 rpm, knock control sensor output voltage is lower than standard (2 trip detection logic).


Open in knock sensor circuit:

At engine speed higher than 1800 rpm, knock control sensor output voltage is below standard for 2.5 seconds (2 trip detection logic).



·

Open or short in knock control sensor circuit

·

Knock control sensor

·

Knock control sensor looseness

·

ECM


Comes on DTC stored Engine A
P032515 Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open At least 15 seconds after engine was started, at engine speed higher than 680 rpm, knock control sensor output voltage is higher than standard (2 trip detection logic).
·

Open or short in knock control sensor circuit

·

Knock control sensor

·

Knock control sensor looseness

·

ECM


Comes on DTC stored Engine A

HINT:

If the ECM detects DTC P032511 and P032515, it enters fail-safe mode in knock feedback control operation condition (engine load is 40% or higher and engine coolant temperature is 40°C (104°F)).


WIRING DIAGRAM

A322491E06
0.875,2.229 1.333,2.427 0.458,0.198 10 false D33 0.875,2.365 2.24,2.573 1.365,0.208 10 false Knock Control Sensor 4.021,0.927 4.479,1.125 0.458,0.198 10 false 97 2.031,1.792 2.49,1.99 0.458,0.198 10 false 2 2.802,2.188 3.26,2.385 0.458,0.198 10 false * 1.917,3.271 3,3.5 1.083,0.229 10 false *: Shielded 4.021,1.792 4.479,1.99 0.458,0.198 10 false 96 3.958,2.406 4.417,2.604 0.458,0.198 10 false 122 2.031,0.927 2.49,1.125 0.458,0.198 10 false 1 4.271,0.927 4.729,1.125 0.458,0.198 10 false KNK1 4.271,1.792 4.729,1.99 0.458,0.198 10 false EKNK 4.271,2.51 4.729,2.708 0.458,0.198 10 false DE12 5.021,3.125 5.479,3.323 0.458,0.198 10 false D50 5.406,3.125 5.844,3.365 0.438,0.24 10 false ECM 1.552,0.938 2.167,1.135 0.615,0.198 10 false KNK1 1.542,1.802 2.156,2 0.615,0.198 10 false EKNK

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


DTC P032511 and P032515 are detected when the vehicle is driven at approximately 100 km/h (62 mph) for 1 minute or more (at an engine speed of 1800 rpm or more, with an engine load of 40% or more after warm-up).

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - KNOCK CONTROL SENSOR)

Pre-procedure1

a.

Disconnect the ECM connector.


b.

Disconnect the knock control sensor connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D50-97 (KNK1) - D33-1 (KNK1) Always Below 1 Ω
D50-96 (EKNK) - D33-2 (EKNK) Always Below 1 Ω
D50-97 (KNK1) or D33-1 (KNK1) - Body ground Always 10 kΩ or higher
D50-96 (EKNK) or D33-2 (EKNK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

2.CHECK KNOCK CONTROL SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK KNOCK CONTROL SENSOR INSTALLATION
a.

Check the knock control sensor installation condition.

OK:

Knock control sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

3.REPLACE KNOCK CONTROL SENSOR

NG

SECURELY REINSTALL KNOCK CONTROL SENSOR

3.REPLACE KNOCK CONTROL SENSOR

NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P032511 OR P032515)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P032511 OR P032515)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTC P032511 or P032515 is output A
DTCs are not output B


Post-procedure1

d.

None.



A

B

END